Search Documents

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By A. A. Cochran

Bureau of MinesThe Bureau of Mines studied the development of practical methods for recovering manganese from the extensive domestic resources of low-grade ores and open hearth slags. A one-step operation was developed on a laboratory scale in which manganese and iron compounds are treated with chlorine, volatilized, and separated by selective condensation. Manganese recoveries of 90 to nearly 100 percent were obtained from 9 of the most important domestic ores. Analyses of the manganese chloride product indicated that it was suit-able for aqueous electrolysis with little additional purification. A complete, integrated process that provides for the recovery and recycling of chlorine is proposed. This process appears to have distinct advantages over previously proposed manganese recovery processes, and, in sharp contrast to leaching procedures, it is applicable to practically any manganese-bearing material.

Jan 1, 1967

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By John W. Finch

The present epoch in human history has been variously described as the age of coal, of oil, of iron and steel, and of power. All agree, however, that it is a great industrial period. Power is of course the vital force in the industrial organism; but power is derived chiefly from mineral fuels or from harnessed and controlled water - also a mineral substance although usually not so classified by industry. However, the latent energy of fuels cannot work for men until it is changed to active energy by combustion and until this active energy is converted into motion. This motion is just as indispensible as the energy itself. Likewise, the latent energy of water cannot be utilized until it, too, is converted into motion; out the mechanisms and devices for converting latent energy into motion, as well as the structures in which they are operated, would not be possible without metals and other minerals. Consequently, minerals are fundamental in industrial civilization.

Jan 1, 1938

By Keith A. Heasley, John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U. S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of are corded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with bump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip, etc.) of the failure of the strata surrounding the active and multi-panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

By Clinton C. Knox

Attention of mine operators and engineers in the Picher zinc-lead field has been drawn increasingly in recent years to marginal ore deposits lying at greater than normal depth below surface in the marked structural depressions known as the Miami and Bendelari troughs. Not only mining but prospect and development drilling is relatively costly in the bottoms of the structural depressions known as the. Miami and Bendelari troughs which cross the center of the Picher field. Nevertheless, operations by various mining companies in recent years have shown that no insuperable problems exist, and with the gradual lowering of grade cut-offs throughout the field, certain potential deep-ore areas, previously only partly explored seemed worthy of further investigation. Some such areas were called to the attention of Bureau of Mines engineers by lease holders and operators, while others were noted in the course of Bureau's systematic investigation of Tri-State ore reserves. The writer was assigned to make a study of. those possible "trough extensions," in the course of which all available nine maps, drill logs, and prior reports were assembled. Subsequently 41 churn drill holes were bored by the Bureau in the periods October 1944 to May 1945 and October 1946 to April 1947. The general area under investigation this project is indicated on figure 1, which likewise shows its relation to nearby towns, roads, and railroads. The location of individual deposits included in the report is indicated more clearly on figure 3. Minable ore was found in only two holes, and the structural information procured by drilling was less encouraging than anticipated. This report, however, presents all factual data obtained, in the belief that they may be useful in subsequent prospecting and development projects in the areas investigated. There are also set forth some of the stratigraphic data relative to the Picher field ns a whole and the Miami and Bendelari troughs which were assembled in the preliminary investigation of this project.

Jan 1, 1949

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By Henry P. Wheeler

Natural gas was first stored underground in Welland, County, Ontario Province, Canada, in 1915.3/ The following year natural gas in the United States was first stored underground successfully in the Zoar field near Buffalo, N, Y. Only three additional storage fields were in use in the United States in 1930, but by 1940 the number had increased to over 30, and since that time growth has been more rapid. At least 80 fields, with a combined storage capacity of 440,828 MM c. f ., were being utilized by 1949.4 / In May 1952, 142 storage projects having a capacity of 915,000 MM c.f. were in operation .5/ These fields are distributed from New York to California--from Michigan to Texas. In the Appalachian region alone, there are 101 storage fields with a combined capacity exceeding 526,000 MM cu. ft. Why Natural Gas is Stored Natural gas is stored in order to be readily available to meet the needs of consumers.

Jan 1, 1952

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By ALICE V. Petar

Among the rarest of the rare metals are four that are linked together by a common historical background as well as by chemical relationship. With the excep- tion of indium, these metals are likewise characterized by the patriotic nature of the names given them by their discoverers. The existence of gallium, germanium, and scandium, was predicted by the Russian cherist, D. I. Mendeleeff some time prior to their discovery; and these elements might well have been overlooked, had not the search been stimulated by the urge to confirm the scientific hypothesis of their existence. Nowhare found in sufficient quantities to attract attention, these little known elemente are nevertheless widely distributed in the earth's crust. So far they are found commercially mostly in the sulphide ores of zinc and must be considered as being largely curiosities of the zinc smelter. Recent progress in electrolytic zinc refining, however, now gives promise that the way may be open for the recovery of these very rare metals in larger quantities-- possibly in quantities sufficient to permit of their finding commercial utilization.

Nov 1, 1930

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By W. J. Huff, G. W. Jones, I. Spolan, R. E. Kennedy

"INTRODUCTION Information on the exploeibility and ease of ignition of acetylene is important in connection with investigations by the Bureau of Mines and others seeking the causes of explosions in medium-pressure acetylene generators.A previous report 6/ gave preliminary results of an investigation made by this Bureau to determine the causes of these explosions. This report indicated the need of amending Federal specifications for ""1/4 by 1/12"" carbide to reduce the amount of fine sizes permitted under the specifications then in force. Tests described in the above report showed that certain sizes of carbide may, under certain conditions, attain excessively high temperatures when acetylene-water vapor mixtures are passed through carbides for extended periods.Federal specifications P-0-101, Amendment 5, June 28, 1944, are now in effect. These latest specifications permit a maximum of 7 percent of ""1/4 by 1/12"" carbide by weight to pass through a 0.0661-inch sieve and a maximum of 2 percent to pass through a 0.0555-inch sieve. Experience has shown that these specifications have insured a safer size range of carbide for medium-pressure acetylene generators.Although the improvement in the size range of the carbides has aided in the prevention of explosions, there have been explosions in which the carbide used at the time of the explosion met the latest Federal specifications."

Sep 1, 1945

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

By Michael G. Zabetakis, Aldo L. Furno, Henry E. Perlee

The Bureau of Mines conducted an experimental study with liquid and gaseous hydrogen to determine the hazards associated with the use of liquid hydrogen as an ionizing particle detector in bubble chambers . The glass window , the vacuum chamber , and the vent system were investigated . In addition , a study was made of the detection and ignition of escaping hydrogen and of the available electrical equipment for use in hydrogen atmospheres . Materials such as tempered glass , aluminum , and stainless steel are not penetrated readily by the small fragments formed when fully tempered glass is shattered and propelled by hydrogen at initial pressures up to 100 psig ; long , slender fragments from untempered glass may penetrate thin walls of relatively soft materials such as rubber gaskets and lead . Hydrogen can be vented satisfactorily from a vacuum chamber with a well - designed vent system . However , the rapid leakage of hydrogen into the surrounding air is a serious problem because the available detectors are satisfactory only when the accumulation of hydrogen is slow . Much of the electrical equipment currently available was designed for use in hydrogen- air atmospheres .

Jan 1, 1963