Search Documents

By W. D. Ludemann, E. A. Loria, E. A. Rowe

The isothermal recrystallization of electrorefined vanadium has been studied as a function of annealing time , temperature , and prior deformation . Specimens were cold- rolled from 30- to 75 - percent reduction in thickness , then annealed from 700 ° to 1,200 ° C at time periods ranging from 1 minute to 96 hours . The course of recrystallization was followed by means of hardness , metallographic , and X- ray techniques , and a recrystallization diagram was constructed . Interpretation of the data indicated that there was around 50- percent softening due to recovery ( first stage of softening) before recrystallization began . The defining of recrystallization limits with respect to the amount of deformation was precisely established for electrorefined vanadium . More than 30- percent reduction was necessary for recrystallization to occur at 850 ° C. With 60- percent reduction , it was initiated at 750 ° C and completed at 950° C. The activation energy for recrystallization , as derived from the data , was 95,300 cal per mole for 60 - percent reduction and annealing at 750 ° to 900 ° C. Recrystallization by the mechanism of nucleation and growth was the principal process during the second stage of softening . minor part of the second stage of softening took place as strain- induced boundary migration , which was observed in specimens reduced 30 percent , bent in L- shape , and annealed at 950 ° C. Grain size decreased significantly only with the largest reductions and annealing between 750 ° and 950 ° C. Grain growth was expressed by the empirical relation D = KKtt"" ,, the exponent being the same at 60- percent reduction and annealing from 750 ° to 900 ° C. Accordingly , the activation energy for grain growth was 75,000 cal per mole .

Jan 1, 1964

By Charles Vaught, Michael J. Brnich, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.2 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Underground coal miners Length: 9 questions (30 minutes for administration and 30 minutes for discussion) Skills: Mine fire escape strategies/procedures Use of emergency breathing apparatus Knowledge of sensations experienced when wearing breathing apparatus Communication Location: Underground coal mine section, average 60 inch seam height Problem: You are the section foreman on the 17 Left longwall development section at the Paula Ann No. 3 mine. The section has been driven about 4,000 feet from 4 West Mains. One of the shuttle car operators took a call from the fireboss saying that there was smoke from an unknown source coming into your section. You attempt to contact someone to find out where the smoke is coming from but get no response. You assemble the crew and start riding out of the section on the mantrip when you encounter heavy smoke. At this point, you decide to take your crew and travel on foot in the belt entry that is on a neutral split of air. After traveling about 6 crosscuts in the belt entry, you encounter heavy smoke at which time you and your crew don your person-wearable SCSRs (PWSCSR). After donning the apparatus, you and your crew continue traveling outby in the belt entry. Near the mouth of the section, one miner in the group starts to have trouble breathing from his SCSR. Because breathing resistance is increasing with the length of time the apparatus is worn, the miner is "outbreathing" the device since his oxygen requirements are greater that what the PWSCSR can supply. Although you slow

Jan 10, 1999

By H. R. O'Brien

"During the past year, the Pittsburgh experiment station of the Bureau of Mines has been investigating methods for the quantitative estimation of carbon monoxide in blood. This work was necessary because reliable methods of analysis are of the greatest importance in the bureau's research work on prevention and treatment of carbon monoxide poisoning among workers in mines and metallurgical plants. Two of the methods considered involve color comparisons. In one of these methods, differences in tint can be noted fairly readily, while in the other, they are much more difficult to detect. The latter, however, is otherwise considerably simpler. It was decided, therefore, in studying the possibilities of this second method, to use the most sensitive eyes in the laboratory force.Preliminary trials.The method under investigation was the Haldane carmine determination of carbon monoxide in blood. The plain oxyhamoglobin of the blood in dilute solution is a pale straw color, when exposed to carbon monoxide it becomes a cherry pink. In the analysis dilute indigo carmine is added to oxyhsmoglobin until the solution matches in tint the carbon monoxide hemoglobin. The eye wanted, then, was the one most sensitive to faint pinks. But just how to select the analyst was not clear At first the Williams test scale, used in the Navy, was considered, but on con¬sultation with Dr. L. L. Thurston, bead of the Department of Psychology at Carnegie Institute of Technology, the following procedure was adopted.Instead of standard tests made up of all colors, only those occurring in the analysis were used. Solutions were prepared of the two hemoglobins, from which twenty-four different pairs were made up and placed in test tubes like those expected to be used in the analysis. One of each pair differed from the other in percentage of carbon monoxide hemoglobin by amounts varying from 2-1/2 per cent to 20 per cent. Each pair was compared in a box built in our own shop. This was 20 inches long and 5 inches square in cross section. One end was covered with ground glass. Just inside this glass cover were provided two slots, each the width of the test tubes used. The tubes to be compared were dropped into these slots through two holes in the top of the box. The device was placed before a window away from the sun, and so arranged that the light conditions were the same on each slit or opening. The person to be tested was seated before the box, and as the two tubes were placed before him side by side, he marked whether A (left) or B (right) contained the more cherry pink. This procedure was continued till he had compared all the pairs."

Jul 1, 1921

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By Eldon Keith Stanek

This annual report deals with a multi-faceted research effort to increase mine electrical system safety. The project can be broken down into six task areas. Task one deals with the development of tests and instrumentation to perform these test- that are designed to detect incipient faults on mine power systems. This program also encompasses evaluation of the tests and automation of data collection and recording using a microprocessor. Task two concerns the prediction and suppression of mine electrical transients. This program involves digital simulation and suppression hardware evaluation. Task three deals with the reliability and fail safe assessment of various components of the mine electrical system including both the protective system and bulk power system components. Task three deals with theoretical analysis, laboratory testing and in-situ testing in coal mines of power system devices. Task four is an effort to design an optimal mine electrical distribution system. The initial effort is along the lines of refining analytical tools such as the load flow model. Task five is an attempt to optimize the selection of molded case circuit breakers makes or models on the basis of total annual cost. Task six assesses the availability of equipment to satisfy existing federal regulations.

Jan 1, 1977

By James Westfield

A brief resume follows of some recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors during their inspections of bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, following further consultations with representatives of management and mine workers, and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. The inspectors were active in making prompt investigations of hazardous mines that had been closed by order of the Coal Mines Administrator to determine if enough improvements had been made to allow the mines to reopen. Federal coal-mine inspectors also had temporary authority to close mines they found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1957

By James R. Boyle

The value of mineral production increased 6.2% in 1976. With the exception of coal, practically all commodities registered an increase in production and value; most had an increase in unit value. Total value exceeded $1 billion for the first time. The increase in nearly all nonmetallic mineral production was a complete reversal of the 1975 experience. Alabama led the Nation in the production of crushed marble and was second in bauxite and scrap mica, third in oystershell, third in kaolin, and fifth in dimension limes-tone and dimension marble. International Trade.-The international trade passing through the Mobile customs district was valued at $2,524 minion in fiscal year 1976, up 20% from that of the previous year. Of the total value of trade passing through the district, 52% of the value of experts and 89% of the value of imports were handled through the port at Mobile. The major export Commodity was coal through McDuffie Coal Terminal which amounted to nearly 2.9 million tons, up from 2.4 million tons in 1975. Coal exports were to Japan, Italy, Turkey, the United Kingdom, and Brazil. Other exports were cement (114,000 tons) and [ ]

Jan 1, 1979

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By L. C. IlsLey

The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Weatstone-bridge and catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detractors of the latter type have been approved since 1930. A brief description of each follows: U. C. C. Detector Approval No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was extended. January 27, 1930, to cover important changes in design that permit checking the calibration of the detector at any time whether in gas or fresh air. Essential features of the detector are shown in figure 1.

Jan 1, 1937

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Development of downstream petrochemical and fertilizer industries continues as a major investment area. In 1993, the 15 countries that constituted the region accounted for 29 % of world crude petroleum output, 19 % of world natural gas plant liquid production, and 6 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Regional output was up for most major mineral commodities. A major exception was phosphate rock, which declined sharply owing to reduced worldwide demand. Total crude petroleum output declined by over 100 Mbbls, again owing to slack demand in the major industrial countries.

Jan 1, 1995

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

While coal occurs beneath about 18 percent of Utah, only 4 percent of the state has minable reserves. Utah's coal fields are mostly bituminous. Current coal production in Utah is largely by underground mining, making Utah unique among the coal-producing states. Most coal seams are more than 8 feet thick. Utah's coal resources are about 6.3 billion tons, 1.3 percent of the national reserve. Most of Utah's coal resources are held by the Federal Government and Indian tribes and are mined under lease. The climate of the Utah coal region is characterized by hot, dry summers and cold, relatively moist winters. Normal precipition varies from 6 inches in the lower valleys to more than 40 inches on some high plateaus. The growing season ranges from 5 months in some valleys to less than 3 months in mountainous regions. These extreme climatic conditions make reclamation difficult. Utah gained primacy when its regulatory program was conditionally approved January 21, 1981. Full program approval was obtained March 7, 1983. The Abandoned Mine Land Program was approved June 3,1983. A Federal Lands Cooperative Agreement was signed in March 1987; Utah performs all enforcement activities and some permitting activities on federal lands.

Jan 1, 1992

In 2005, a total of 7,111 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). ? Sand and gravel mines were the largest mining sector, comprising 48.5% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By O. Terichow

A pendulum sclerometer designed by the Bureau of Mines is described. Its method of operation is given, along with the results of tests made on representative mineral samples of Mohs' hardness scale to determine the applicability of the device for research on rock testing. The sclerometer hardness values obtained from the tests indicated that reproducibility and accuracy were good. A quantitative comparison of the pendulum hardness values with microhardness and surface energy values published by other investigators showed good agreement on minerals with Mohs' hardness numbers of 2 to 9.

Jan 1, 1967

By D. E. Emerson, C. G. Kirkland, E. M. Frost

An apparatus has been developed for determining the helium content of gases containing 40 percent or more helium . It utilizes activated coconut charcoal at liquid nitrogen temperatures to adsorb constituents other than helium in the mixture . Series of analyses have been run where the mean deviation was less than 0.05 percent helium . Twenty or more analyses can be made in an 8- hour day .

Jan 1, 1964