Search Documents

By W. A. Haley

This is the second of a series of publications that describes the progress of mechanical longwall coal mining in the United States in which a German coal planer was employed.3/ Details of the equipment, a description of its operation, and the results obtained in mining the experimental panel were published in the preceding report. Experimental mining with the planer in the first panel showed an improvement in performance over conventional mining methods at the coal company's Stotesbury 11 mine. The work, which was begun on an experimental basis, soon proved successful, and the coal company purchased the equipment for continued use. Two panels, adjacent to the first, were developed and mined with the planer. Each of these panels was shorter than the preceding one because water seepage from a surface creek limited development. On completion of mining in the third panel, the planer equipment was moved by the cooperating company to a nearby mine operated in the same coal bed where a large area of coal suitable for planer mining is available.

Jan 1, 1954

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By Louis A. Panek

The practice of roof bolting, now recognized as an effective method of support, is based largely on rule of thumb. Among the various applications of bolting, the support of stratified mine roof is by far the most common. The general principles relating to this type of reinforcement are presented in two companion reports; the first describes the function of the bolts, the bolting pattern, and the behavior of bolted roof (1), 2/ and the second describes the design of the models and the theory of the experimental method (2). This report presents a rational method for designing systems of vertical bolts to reinforce horizontally bedded mine roof, developed from model tests. The structure treated herein may be described as follows: The immediate roof, consisting of beds of like material and equal thickness with no bond between them, is reinforced by vertical bolts installed in straight lines across the opening; the case of suspension is excluded because the bolts are assumed not to extend above the immediate roof. The assumption is made that the behavior of the lowest bed approximates that of a rectangular plate clamped along two opposite sides (the ribs). These specifications represent approximately the roof conditions encountered in mining bedded deposits of all kinds - coal, potash, iron ore, etc. Thus, for the design of a roof-bolting system a quantitative solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, how does the support depend upon the length, spacing, and tightness of the bolts?

Jan 1, 1956

To separate complex mineral mixtures according to their dielectric properties. Approach Develop a laboratory-scale continuous dielectric separator to separate mineral mixtures by exploiting their difference in dielectric properties. How it Works Dielectric separation is de-fined as the separation of particles based on their dielectric properties. The uniqueness of the Bureau's continuous separator, called the ?Rotating Drum Dielectric Separator,? is that it contains a high-voltage electrode con-figuration. The drum electrode consists of a series of coaxial parallel wires mounted on the outside surface of an Insulated cylinder. The screen electrode Is a wire mesh, quarter cylinder positioned outside and coaxially with the drum electrode. The drum electrode is placed in a liquid of dielectric constant K with the liquid level just above the drum's axis. The screen electrode is completely Immersed

Jan 1, 1981

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By Brinton C. Brown

This paper describes the methods and equipment developed at the Bureau's Experimental Oil-Shale mine near Rifle, Colo., for placing men in position to scale loose rock from the walls, pillars, and roofs of high stopes or rooms. The equipment developed at Rifle has application not only in oil-shale mining but in most of the country's underground limestone mines and in the exploitation of other mineral deposits mined in high stopes by room-and-pillar methods. Equipment in use at Rifle includes: 1. A boom-type scaling rig with a self-leveling platform constructed on a small "cat"-mounted crane. Men working from the platform on this machine can efficiently scale mine walls and roofs 27 feet above the floor. 2. A conventional fork-lift truck modified to provide a remotely controlled working platform from which men can scale to heights 27 feet above the mine floor. The platform on this unit is larger than on the boom-type rig and allows the men to inspect larger areas of the mine wall from a single setting of the machine. 3. A third rig, consisting essentially of a platform mounted on a tele-scoping tower, designed and built to elevate men 65 feet above the mine floor. Versatility of this machine permits men to work from the platform at heights of 5 to 65 feet. In the operating position, the unit requires a minimum clearance of 25 feet. In the nonoperating position the tower of the machine folds to an over-all height of 15 feet 10 inches to permit travel through haulageways. 4. An industrial gun, lightweight scaling bars, and mechanical scalers, which have been tried for removing loose rock from the mine walls with varying degrees of success.

Jan 1, 1950

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

By M. J. Reasor, J. M. Antonini, L. Wu, K. Van Dyke, Z. Ye

The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and· laboratory animals. Currently, no effective treatment exists for workers who may have been exposed to the inhalation of silica. The objective of this study was to develop an animal model in which we could evaluate the effect that anti-inflammatory steroids have on the acute silica-induced pulmonary inflammatory response. Male Fischer 344 rats were pretreated with either dexamethasone (2 mg/kg) or saline vehicle (i.p.) on days 1, 3, and 5. On day 6, the animals from the two groups were then intratracheally instilled with either silica (20 mg/0.5 ml saline vehicle) or saline vehicle (0.5 ml). Twenty-four hours after the instillations in the non-steroid group, significant increases occurred in total protein, total number of cells, neutrophils, and lymphocytes recovered from the lungs of animals treated with silica compared to saline controls. Silica also caused dramatic increases in the luminol-dependent chemiluminescence (LDCL) of lung tissue and bronchoalveolar lavage (BAL) cells. The LDCL reaction was markedly decreased by either superoxide dismutase (SOD) or N-nitro-L-arginine methyl ester hydrochloride (L-NAME). SOD is involved in the enzymatic breakdown of superoxide anion, while L-NAME, a nitric oxide (NO) synthase inhibitor, prevents the formation of NO. When the superoxide anion and NO react, they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent which may be involved in the silica-induced oxidant lung injury. When the animals were pretreated with the steroid dexamethasone, there was a complete protection against the biochemical, cellular, and chemiluminescent indices of damage caused by silica. The mechanism in which the steroid protects the lung from damage may be due to the ability of dexamethasone to block the induction of NO synthase. With further study in animals, the anti-inflammatory steroids may be useful in the treatment of silicainduced lung injury.

Dec 1, 1995

By W. L. Dare

This information circular is one of a series, published by the Federal Bureau of Mines, on methods and costs of mining uranium ore on the Colorado Plateau. This report describes the relatively small-scale operations of the Salt Wash miner: The mining method followed, the equipment used, and the production costs. It describes 10 lease-operated mines of Union Carbide: Nuclear Co. that are typical of Salt Wash operations on the plateau. These mines lie within the Uravan mineral belt3/ and arc in the Gateway, Bull Canyon, and Uravan mining districts. (See fig. 1.) Generally the ore bodies occur as irregular, discontinuous layers of ore minerals within sandstone beds in the Salt Wash member of the Jurassic Morrison formation. The ore bodies sometimes occur as rolls, pod associat with carbonaceous trash, or tabular masses. Their size and erratic distribution preclude the use of a prearranged and uniform stoping system. The mining method is simply to follow the ore and leave open scopes behind.

Jan 1, 1959

By N. N. Moebs

The atmosphere in part of an air-sealed coal mine was monitored continuously through a drill hole for oxygen content to determine the effectiveness of sealing a mine against the entrance of air and the major force that caused the phenomenon of mine breathing through the overburden. The differential pressure across the seal and the barometric pressure on the outside also were recorded. A general correlation, obtained between the oxygen level, differential pressure, and barometric pressure, indicates that changes in air pressure are the cause for periodic replenishment of the oxygen in the mine. Mine effluent quality was determined by conditions in many sections of the mine and could not be related to the oxygen level at the drill hole.

Jan 1, 1972

By Robert J. Timko, R. Lincoln Derick

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just in by the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized program, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 1995

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor shaft displacement. Results of a recalibrated two-dimensional model (UTAH2)confirmed the premining stability evaluation. However, after mining began, concern developed because of cracks and other signs of ground motion that appeared at considerable distances from the area of active pillar mining. An intense three-dimensional modeling effort using the computer modeling program UTAH3 was initiated. The results again showed the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternate pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought on the basis of two-dimensional analyses. This report focuses on startup and implementation of the three-dimensional model, calibration of the three-dimensional model, and application of the model to shaft pillar mining.

Jan 1, 1996

By Thomas C. Mowatt

Preliminary Bureau of Mines studies of mafic igneous rocks collected from the Rabbit Creek area, northwestern Alaska, indicated concentrations of platinum (412 to 1,406 ppb) and palladium (343 to 892 ppb) in five of eight samples analyzed. The samples represent boulders and cobbles of mafic/ultramafic rocks from this locality. They are not from outcrop. Petrologically, (on the hand specimen scale) the samples are crudely to well-layered and are troctolitic ± gabbroie in character, with primary igneous mafic minerals strongly altered. Small patches of interstitial sulfide minerals, including chalcopyrite, bornite, pyrrhotite, pyrite, and covellite are associated with these altered zones and elsewhere through the specimens. Copper values ranged from 0.1 to 0.3 pct in samples analyzed semiquantitatively; nickel, cobalt, and chromium contents are low. Chemical, mine alogic, and petrographic relationships suggest that the rocks of similar character outcropping in northwestern Alaska could also be considered as prospective for- concentrations or platinum, palladium, and copper.

Jan 1, 2011

By Sol Weller

The Fischer-Tropsch synthesis consists of the formation of long-chain hydrocarbons by passage of carbon monoxide-hydrogen mixtures over metal catalysts, usually based on iron, cobalt, nickel, or ruthenium, at temperatures in the range 180°-300° C., and at pressures of 1-15 atmospheres. Although the reaction has been known and studied for more than 20 years, the mechanism by which it occurs is still poorly understood. One approach to understanding is to consider the effect upon the course of the synthesis of variations in each of the important operating variables. Consideration of the experimental data pertaining to these variables may suggest an over-all picture describing the synthesis - a picture which, in turn, would have to be consistent with all the known facts. The first part of this paper will be concerned with such a consideration of operating variables; the second portion will discuss recent work pertaining to the role of metal carbides as intermediates in the synthesis.

Jan 1, 1949

By R. B. Schluter

The objective of this Bureau of Mines investigation was to determine the effects of adding manganese compounds and ores to iron ore pellets. Manganese dioxide, carbonate, sulfate and chloride, plus six manganiferous ores from the Minnesota Cuyuna Range were tested as additives to increase the manganese content of iron ore pellets. One to 5 percent manganese, as a compound or ore, was added to five magnetite concentrates and one hematite concentrate. These concentrates were ballad, indurated (1,300° C), and tested for reducibility. Manganese sulfate and chloride were unsatisfactory additives causing cracking and degradation of the pellets during reduction. Manganese dioxide, carbonate, and the ores were satisfactory additives. The additives increased pellet compression strengths with a corresponding loss of reducibility, as compared to the pellets without manganese additions. The changes in compression strengths and reducibility were caused by the formation of Jacobite spinel and slag within the pellets. However, when the induration temperature was lowered from 1,300° to 1,200° C the reducibility and compression strengths were comparable to the pellets without manganese additions indurated at 1,300° C.

Jan 1, 1974

By M. I. Copeland

The investigation of the zirconium-gadolinium equilibrium diagram was part of a program to investigate rare:earth alloys for use as nuclear reactor control materials. Investigation of the zirconium-gadolinium equilibrium diagram revealed a eutectic system with limited terminal solubilities and one peritectoid reaction. The eutectic composition occurs at about 82 percent gadolinium, and the eutectic isotherm, which occurs at 1,220 ±5° C., extends from about 12 to 99+ percent gadolinium. A peritectoid isotherm occurs at 890 ±5° C. and extends from about 2 to 99+ percent gadolinium. The solubility of gadolinium in beta zirconium decreases from about 12 percent at 1,220 ±5° C. to about 2 percent at 890 ±5° C. The solubility of gadolinium in alpha zirconium decreases from approximately 5 percent at 890 ±5° C. to between 2 and 3 percent at 600° C. Vary little solubility of zirconium in gadolinium was indicated. An allotropic transformation of gadolinium was observed at 1,260 ±5° C. A change of the gadolinium transformation temperature on alloying with zirconium was not observed.

Jan 1, 1961

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938