Search Documents

By Elizabeth A. Johnson

The effect of slag composition on lead losses to slags and on the behavior of associated accessory elements in lead blast furnace smelting has been studied by the Bureau of Mines. Equilibrations of 30 g of lead and synthetic slag doped with Cu, In, TI, and Sb at 1,200° C in CO-C02 atmospheres revealed the importance of the FeO:Si02 ratio and the basicity ratio, (CaO+MgO):SiO2, of the slag. Lead losses to slags increased with an increasing FeO:Si02 ratio and decreased with an in-creasing basicity ratio. Copper and indium distribution coefficients, [Lx =] increased from 15 at the lower basicity ratios to near 60 at higher basicity ratios. LTI values increased from 20 to 150 as slag basicity increased. Lcu, Lin, and LTI were relatively in-dependent of the FeO:Si02 ratio, but increased with greater amounts of accessory elements in the system. Antimony distribution alone was shown to be strongly affected by FeO:Si02 ratio, although data were scattered. LSb values ranged from 20 to 800 and decreased sharply with increasing FeO:Si02 ratios. The basicity ratio and the level of accessory element load did not have any noticeable effect on LSb.

Jan 1, 1983

By Thomas C. Miller, Rudolph Sporcic

A relatively simple and inexpensive encapsulated hydraulic device has been developed by the Bureau of Mines to facilitate study of coal bumps , and to measure pressure changes in a coalbed as it is subjected to roof loading during mining . Construction of the device and application techniques are described . Preliminary feasibility tests in the laboratory and field indicate that the device responds satisfactorily to pressure changes in coal created by roof loading .

Jan 1, 1964

By T. H. Ueng, S. D. Thompson, Y. J. Wang

"INTRODUCTION There is considerable interest among mining companies and government agencies in finding new ways to better control the generation and dispersion of respirable coal dust. Mine face ventilation generally has been considered the most effective tool for lowering the concentrations of respirable dust. Unfortunately, only a limited amount of research has been undertaken to determine the relationships between the various face ventilation parameters and the dust dispersion patterns. If these relationships are better understood, more efficient ways of controlling dust generation and dispersion may be evident. A practical and economical way to gain more in-depth understanding of these relationships is through scale model studies. Past research (1, 2, 3) has substantiated that scale models can be successfully used in studying ventilation parameters provided that geometric, kinematic, and dynamic similitues are maintained.To better understand face ventilation and dust dispersion, a 1/5 scale model of a room and pillar mine face was constructed. This model was then used to conduct experimental investigation on two ventilation parameters. The parameters which were examined included the line brattice distance from the face and the air quantity. The values of these parameters were varied in numerous experiments so that their effects on dust dispersion could be measured.The experiments of this study were unique in two ways. First, two different substances were used to simulate the respirable coal dust. Experiments were conducted with a tracer gas (methane) serving as the dust simulation substance. They were then repeated with an actual dust (Arizona Road Dust) replacing methane as the dust simulating substance. In previous scale model studies, the dust simulation substance has been limited to a tracer gas such as methane. The validity of using a tracer gas to simulate dust is not clearly known yet. The other unique thing about these experiments was the number of points measured for methane (or dust) concentration. Twenty five points in a grid arrangement were measured during each experiment of this study. The number of points measured for concentration in other studies has generally been very small (often 2 to 4). It is difficult to obtain an accurate assessment of how the ventilation parameters are effecting dust dispersion when only 2 to 4 points are measured."

Mar 1, 1989

By Kenneth B. Higbie

Expenditures to advance scientific technology in general reached an all time high in 1965 with some $22.2 billion estimated to have been allocated by government and industry. Federal Government expenditures were estimated at $15.4 billion, with almost 90 percent of the funds devoted to programs involving defense, atomic energy, and outer space efforts. With this massive effort in the United States and a very impressive effort elsewhere in the world, there is little wonder that many new metallurgical developments were announced in the technical press during the year. No effort has been made to cover all aspects of the industry, but a few of the developments are described in this chapter.

Jan 1, 1966

By Robert L. Thorne

As an integral part of the investigation of critical and essential minerals in Alaska , the Bureau of Mines examined the lead deposits in the Slana area . Four examinations were made during June , July, and August 1945 in the 200 - square -mile area immediately northwest of Slana . The settlement of Slana lies near the conflux of the small Slana River with the mighty Copper River less than 60 miles southwest of Tek Junction on the Alaska Highway . Travel through the area and the examination of the properties were conducted by a three-man crew consisting of the author , a caterpillar operator , and a laborer . An RD6 caterpillar , equipped with blade and winch , was used in breaking trail and freighting through the country . Supplies and equipment were loaded on a 7- by 14 -foot , double - end , go -devil , which was hauled by the tractor .

Nov 1, 1946

By Stephen Utter

This report summarizes the procedure and results of an investigation to determine the stresses in the rock around an underground opening in the Climax molybdenum mine, Climax, Colo. This study is part of an overall investigation conducted by the Bureau of Mines to determine the stresses induced by block-caving mining. The purpose of this study is to obtain estimates of the magnitudes and directions of the principal stresses, the location of the maximum stress concentrations, and the effect of topography on the stresses.

Jan 1, 1962

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By R. B. Schluter

The Bureau of Mines investigated the flotation responses of two copper-nickel ore samples from the Duluth Complex with the objective of recovering bulk sulfide concentrates. One of the ores studied was taken from a test pit; the other was taken from a test shaft. The samples were quite similar except that the pit sample analyzed 0.35 pct Cu and 0.11 pct Ni and the shaft sample analyzed 0.69 pct Cu and 0.14 pct Ni. Flotation responses were studied in both laboratory and pilot plant tests. Pilot plant flotation responses were similar for both samples resulting in grades of 12.2 pct Cu and 2.5 pct Ni for the pit sample and 12.2 pct Cu and 2.1 pct Ni for the shaft sample. Weight recoveries were 2.5 pct for the pit sample and 5.2 pct for the shaft sample. Copper and nickel recoveries for the pit sample were 87 and 62 pct, respectively, and 92 and 73 pct for the shaft sample. Both concentrates contained small but significant values of cobalt and precious metals. Cobalt recoveries were low--less than 40 pct for both concentrates. Precious metals contents of the concentrates were 1.59 oz/ton for the pit sample and 0.99 oz/ton for the shaft sample. Silver was the predominant precious metal by weight, but platinum and palladium represented the highest values.

Jan 1, 1980

By M. E. Tyrrell

The purpose of the work leading to this report was two-fold: (1) To determine the properties of cemented tungsten carbide modified by the addition of one, two, and five percent of titanium diboride, and (2) to compare the properties of these mixtures when sintered, hot-pressed, and flash-welded (resistance-sintered). Minor additions of titanium diboride to mixtures of 94 percent WC and 6 percent Co decrease mechanical strength but increase oxidation resistance in proportion to the amount of the addition. One percent of titanium diboride increased the hardness by 2 Rockwell A units. Hot-pressing produced compacts with the highest density and the best mechanical strength, but losses of cobalt were high and grain growth was pronounced.

Jan 1, 1962

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By W. A. Cole

The sulfur shortage that existed during the Korean conflict stimulated interest in coal measures as possible sources of sulfur. One of the areas brought to the attention of the Bureau of Mines was in Marion County, Iowa, where comparatively high-sulfur coals and other marcasite-bearing strata were known to occur. A Bureau of Mines engineer inspected the marcasite occurrence on December 4, 1954; this prompted further work on the Iowa coals and associated formations as a source of iron sulfides. An investigation of the Iowa high-sulfur coals was undertaken including core drilling, field reconnaissance, and compilation of data pertinent to consideration of the following: 1. Upgrading Iowa coal by mechanical cleaning and the feasibility of recovering sulfur from coal brasses. 2. Possibility of processing the high-sulfur coals by adaptation of methods employed in processing industrial gases to produce sulfur and sulfur products. 3. Possibility of finding concentrations of iron sulfides in associated rock formations in sufficient quantity for economical recovery.

Jan 1, 1957

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By W. E. Robinson

Sixty samples, selected from a 2,300-foot core of the Green River Formation in Colorado, were studied to ascertain differences in the structure of the organic material present in the oil shale samples. Emphasis was placed upon relating differences in the aromatic content of the insoluble kerogen and the alkane content of the extractable material obtained from the selected samples. The methods used in determining these differences consisted of fractionation of the soluble material, carbon and hydrogen analysis, volatile material determination, carbon residue determination, oxidation rate determination, and infrared analysis. In general, it was concluded that the organic material in this core does vary in chemical structure and that same of these variations resulted from factors related to depth of burial. Other observed changes in structure of the organic material were not depth-dependent and resulted from other factors such as source material variations, biological alterations, or ecological differences.

Jan 1, 1971

By L. W. Brandt

Studies of liquid-vapor equilibria of gas mixtures at the Bureau of Mines Amarillo Helium Plant Laboratory require that the equilibrium cell be maintained uniformly at any desired temperature from approximately room temperature to -320° F. The temperature-control system must also tolerate a substantial heat input, in the form of warm gas flowing into the cell, without loss of control. Temperatures between the sublimation temperature of carbon dioxide (-109° F.) and the boiling point of liquid nitrogen (320° F.) are usually obtained by methods utilizing a hydrocarbon liquid bath cooled by liquid nitrogen.4/5/6/7/ Owing to the fire hazard attending such baths, a safer method of temperature control was desirable.

Jan 1, 1955

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By Kevin Connor

The Government's ban on all commercial mining operations, except for small-scale artisan exploitation of alluvial gold deposits, continued throughout 1985. Minerals produced were kaolin and lime for agricultural uses, and experimental peat harvesting for energy applications. The total value of the minerals produced during the year was estimated at $1.1 million .2 In early 1985, an agreement between the Government and Amoco International Oil Co. was ratified for a petroleum exploration concession covering 248,000 hectares of Lake Tanganyika. Onshore exploration in the Ruzizi Plain was already under way the last half of 1985. By yearend, enough seismic information was available that Amoco hoped to complete data analyses, determine onshore drilling sites, and begin drilling operations before the end of 1986. Also to begin in the latter part of 1986 were seismic studies of Lake Tanganyika. Throughout 1985, Amoco officials were negotiating with the Government of Zaire for expanding the exploration acreage into that country's portion of northern Lake Tanganyika and the Ruzizi Plain. An agreement between Amoco and Zaire could have important beneficial economic implications for both Zaire and Burundi, and onshore seismic work in Zaire logistically supported from Bujumburi could begin almost immediately.

Jan 1, 1987

By Lisa Steiner, Robin Burgess-Limerick

In 2004, there were 646 underground coal mines in the USA employing 37,445 miners. These mines reported 3556 injuries to MSHA that year - 17% were associated with bolting machines (593 injuries), 8% with continuous miners (283 injuries), and 4% each with Scoop/LHD (1 51 injuries), shuttle cars (134 injuries), and personnel transport (145 injuries). The use of the frequency of reported injuries for the prioritization of risk control strategies has limitations because of the tendency to underestimate the importance of relatively rare but high-consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggest the following hazards as the highest priority for elimination or control: • rock falling from supported roof • inadvertent or incorrect operation of bolting controls • handling continuous miner cable • collisions while driving LHD/Scoop, shuttle cars and personnel transport • rough road while driving or traveling in LHD/Scoop, SC & PT

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals4/ and. investigations of their chemical and physical properties.5/ The coal represented by the sample from weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By J. J. Demeter

Anthracite from the four producing regions in Pennsylvania was both ashed in the laboratory and burned on a chain-grate stoker to determine the sulfur-retention properties of its ash. The retention of sulfur in laboratory-prepared anthracite ash was shown to be related to ashing temperature and to the amounts of sulfur and calcium present in the coal. At the usual laboratory ashing temperature of 750° C sulfur retention ranged from 0.8 to 13.2 percent of the total coal sulfur. Sulfur retention in the ash was negligible, o to 0.3 percent, at 1,200° C, which is the thermal decomposition temperature of calcium sulfate; thus calcium sulfate does not form and cannot serve as a sulfur-retaining agent. In several tests the anthracite was mixed with 6 or 10 percent dolomite prior to firing in the chain-grate stoker. The dolomite did not improve sulfur retention owing to the high temperature in the fuel bed. Sulfur retention was, however, related to the unburned carbon in the ash. The relationship of the percentage of original coal sulfur retained in the ash (Y) to the percentage of the original carbon in the coal remaining in the ash (X) is expressed by Y = -0.579 + 0.914X. The percentage of sulfur retained is almost directly proportionate to the percentage of original coal carbon in the ash.

Jan 1, 1968