Search Documents

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By Charles L. Harness, A. T. Coons

Sodium carbonate, Na2CO3, more commonly known as soda ash, is the most important of the alkalies. Sulfuric acid is the only heavy chemical, Soda ash enters the market either as the natural product or as a manufactured derivative of common salt. Notwithstanding their common occurrence in closed basins of the Western States, natural sodas are produced at present by only four firms, all in the same California area, and satisfy only 4 percent of domestic demand for soda ash; soda ash made from salt supplies 96 percent of the requirements. The impossibility in wartime of routing all westbound American shipping through the Panama Cami.l has curtailed Pacific Coast receipts of soda ash and-increased the importance of local resources of natural carbonates. One of the most promising of ·these is the recently discovered trona (sodium sesquicarbonate)· deposit 2o·mnes· west of Green River, Wyo. Reserves are likely to run into hundreds ·of million·s of tons, and the deposit probably could be worked by the room-and~pillar· system of mining, like common salt or coal. • • Raw materials ·ne·cessary for manufacturing synthetic soda ash occur closely associated in m·afiy parts· bf the United 8tates. Almost unlimited resources of salt in brines and in rock-salt depbsits are located near limestone quarries in many areas. The· limesto'ne furnishes the carbon dioxide for the manufacture of soda ash arid the lime f o'r the recovery of ammonia. used in one step of the process. Expansion of the industry to meet wartime needs depends chiefly on availability of trained labor, materials, and equipment necessary for the erection of additional units.

Jun 1, 1942

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are established it can be ascertained with a,of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town, whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well under drained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive."

Jun 1, 1921

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By K. C. Dean

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Stabilization has been attained by physical, chemical, vegetative, and combination procedures. Vegetative reclamation is preferred to physical and chemical stabilization but is diffi¬cult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Methods now have been developed for attain¬ing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $120 to $650 per acre. The cost for stabilizing tail¬ings requiring more intensive treatment techniques may range upward to $1,750 per acre. This report summarizes procedures developed by the Bureau of Mines and industry for vegetating amenable tailings, lists costs for the various processes, and suggests procedures that may be applicable for stabilizing saline and pyrite-containing tailings. Ridged planting beds, drip irrigation, and deep-furrow planting techniques are suggested for stabilizing saline wastes. A combination of mill tailings and sewage sludge can be used for pro¬ducing synthetic soils, and layers of sewage sludge buried under a layer of tailings offer promise of inhibiting acid formation from oxidation of sulfides in mineral wastes.

Jan 1, 1974

By A. C. Fieldner

Much activity is called for in the present period of hightened national effort, and wise direction of such a program must always be conditioned by positive knowledge gained in years of slow and painstaking study and development. Research and technologic investigations on coal by the Bureau of Mines have been described in a series of annual

Jan 1, 1941

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed 'emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and an extensive literature has resulted. Usually each individual paper has placed emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Michael Rieber

Rail cars are referred to as "yellow-balled" when they are sufficiently old or damaged to preclude their efficient operation on long-haul or main line routes. For most coal carrying railroads, their alternative value is salvage. This, however, does not necessarily preclude their effective use, on a limited basis, by small mines located near existing trackage. Because of age, the sizes of these hopper and gondola cars ace currently 50 and 70 tons rather than the 100 tons commonly built at the present time. As a gathering system, yellow-ball rail could provide an alternative, particularly in Kentucky, western Pennsylvania and west Virginia, to coal trucks, conveyor belts and pneumatic pipelines [4, p.17], belts and pneumatic pipelines. Rail service of this type provides a limited alternative to track abondonment, a possible financial return to a railbank [3], a direct contribution to service demand on main lines, and a means by which many small eastern coal mines could retain or regain competitive viability [4]. In terms of energy efficiency, compared to trucking coal, the total direct energy impact (fuel) of yellow-ball rail can be expected to range from 280-990 Btu/ton-mile while that for trucks ranges from 1850-3120 Btu/ton-mile [2].

Jan 1, 1977

By R. W. Watson

At the request of the Mine Safety and Health Administration (MSHA) the Bureau of Mines evaluated the potential hazards of three compressed oxygen self-contained self-rescuers (SCSR's) designed for use in under-ground coal mines. The evaluation followed the lines used in a similar investigation of chemical self-rescuers and involved laboratory experiments as well as field trials designed to simulate a mining environment. They included bullet impact, bonfire, feeder-breaker impact and feed-through, and mining machine runover tests. The work showed that the units were not inherently unsafe but that under certain conditions of extreme abuse they can present a potential ignition or explosion hazard. This, coupled with a survey of reported damage on SCSR's currently deployed in underground mines, which indicated a relatively high frequency of incidents leading to the destruc-tion of the units, led to new recommendations on the deployment of SCSR's. The recommendations formulated by MSHA state that the units should be either properly worn by the miner, stored in heavy containers, or otherwise protected from situations in which they might be accidentally ruptured or destroyed, such as runover by mobile mining equipment.

Jan 1, 1984

By W. D. Walker

The trend toward encouragement of worker participation in accident prevention in the coal mines of the United States is not new; however, it has been given added impetus in recent years and is now definitely progressing. It has been found by experience that, although there are many approaches to a mine-safety program that will include the workers themselves as well as their supervisors, no one way is suitable under all circumstances. It requires the concerted efforts of many agencies working along parallel lines toward a common goal. The following seven principal agencies, using somewhat different methods, are listed to illustrate how this problem is approached throughout the coal-mining industry 1. Federal Bureau of Mines. 2. State mining departments (in individual States where coal is produced). 3. Programs conducted by individual mine operators. 4. Programs conducted by mine workers' organizations (unions). 5. Institutes, societies, and other educational organizations. 6. Coal operators' associations (regional and national). 7. Universities, college, and high schools. Each of the seven approaches to safety are discussed briefly, and their methods end contributions, such as publications and other activities, are listed.

Jan 1, 1953

By James N. Bayne

An examination and analysis of Landsat digital data in the monitoring of surface mines in selected counties of South Carolina.

Jan 1, 1979

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938