Search Documents

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By B. L. Eggers

This study investigates the application of computed order tracking with subsequent rotation domain averaging and statistical analysis, to the drag gearbox of a dragline used in a mining environment. Computed order tracking is a fault detection method developed to deal with the varying speed conditions often found in industry and has been proven effective in laboratory conditions. Its application to real situations, however, requires some adjustment to deal with issues such as inadequate speed data and the fact that the drag gear rotates in two directions. This provides a unique opportunity to observe the performance of the order tracking method in a bi-directional rotating environment, allowing an investigation of the relationships between the results obtained from each operating direction. A monitoring station was set up aboard the dragline and data was captured twice daily for a period spanning approximately one year. The data captured consisted of accelerometer and proximity sensor data. The key on the shaft triggers the proximity sensors, allowing speed and direction to be measured. The measured speed is interpolated by using various speed interpolation techniques. Then the interpolated speed is used to complete the order tracking procedure that resamples the vibration data with reference to the speed. The results indicate that computed order tracking can be successfully employed in real environments. Furthermore it is shown that the rotation direction that opens the gear-tooth crack gives a better indication of incipient failure. It is therefore important not to disregard either direction when monitoring rotating machinery of this kind.

Jan 1, 2007

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By W. P. Roux

Owing to decreasing high-grade ore reserves, there is a need for better understanding of the jigging process to improve the recovery efficiency of finer, lower grade material. The use of positron emission particle tracking (PEPT) was examined as a technique to study the motion of iron ore particles inside a laboratory batch jig. PEPT is a non-invasive method that can provide three-dimensional kinetic data on a particle in laboratory-scale processing units and has been successfully used to study mills, hydrocyclones, and flotation. Experiments were conducted to determine whether PEPT would be a viable technique to study iron ore jigging and what valuable information could be obtained. The results indicated that detailed information on the stratification rate of a particle could be obtained, with adequate resolution to track the particle?s movement through an individual jig pulse.

Jan 1, 2014

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills AQ or BQ holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

By G. van Aswegen

Seismic monitoring became commonplace in the deep South African gold mines in the early 1990’s. The discipline has, to a large extent, developed beyond the ‘research’ stage, and a ‘Guide to Seismic Monitoring in Mines’ has been accepted by the Department of Minerals and Energy1. Although ongoing research is a requirement for the achievement of all the objectives of seismic monitoring in mines, sufficient knowledge exists to apply seismic monitoring for routine seismic hazard assessment as an aid to risk management. The design and management of seismic monitoring systems can be tested against requirements spelled out in the ‘Guide’. Assuming the seismic monitoring system performs as per requirement, the best practice for routine seismic hazard assessment in mines includes • Long term seismic hazard assessment: through back analysis of seismic data and correlation with numerical modelling output, reasonable tests for planned mine designs are possible. • Medium term seismic hazard assessment: o Spatial analysis through contouring of seismic strain related parameters, with superimposed contours or event plots of stress related parameters allow the delineation of potential instabilities in space. o Quantitative and statistical analyses of seismicity in smaller spatial units (usually encompassing production sites) allow the comparative seismic hazard rating of different areas/sites so that rock engineering input and risk management can be optimised • Short term seismic hazard assessment relies mainly on time history analyses of particular seismicity parameters. The temporal patterns are controlled by a combination of temporal and parameter filters, the optimisation of which determines the success rate.

Jan 1, 2003

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011