Search Documents

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By John A. Haggman

Philippines is a country that is richly endowed in mineral wealth. In 1988, Climax Arimco Mining Corp. (CAMC) geologists found the Dinkidi porphyry gold-copper deposit in Nueva Vizcaya province. It is the most significant mineral discovery in that country in recent times. To date, the company has defined indicated resources of 124 Mt (136 million st) of 1-g/t (0.029-oz/st) gold and 0.4% copper. This includes a high-grade core of 7.9 Mt (8.7 million st) of 6-g/t (0.175-oz/st) gold equivalent. Total contained metal is 124.4 t (4 million oz) of gold and 499 kt (1.1 billion lb) of copper. Dinkidi's discovery resulted from initial geologic reconnaissance and recognition of the intrusive complex that is exposed at surface and anomalous in its topographic expression. This was followed by systematic exploration. This includes extensive gradient array induced polarization (IP), ground magnetics, geochemical sampling and diamond drilling. This later defined a further 16 satellite porphyry targets in the Didipio region. Climax was been granted a Financial and Technical Assistance Agreement contract with the Philippine government. It allows 100% foreign ownership of mining projects. After four years of negotiations, Climax was the first company to have such an application granted. Some 120 applications from numerous international mining companies are waiting for approval following implementation of new Philippine Mining Act of 1995. Exploration history Didipio is located 200 km (125 miles) north of Manila at an elevation of about 700 m (2,300 ft) in the remote Sierra Madre mountains. This region remains mostly unexplored. The property is accessed by 25 km (15 miles) of logging track from the town of Cabarroguis, Quirino. The area experiences an average rainfall of about 3,000 mm (118 in.) a year. Most of it falls during the July-to-November typhoon season. Didipio was first recognized as a gold province in the 1970s when native Ifugao and Ilongot hunters discovered alluvial gold in the region. The region had been prospected over the years by local companies. They were mostly prospecting for alluvial gold. However, in 1988, Climax Mining geologists identified the potential of an obscure razorback ridge protruding from the alluvial valley floor. This ridge, later named Dinkidi by Climax, was the site of several small- scale tunnels. Locals had mined narrow quartz stockwork veining and sluiced soft argillic alteration zones, using irrigation canals and sluice boxes to catch free gold.

Jan 1, 1997

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By William Petruk

Lithium bearing lepidolites from three deposits in the province of Goias in Brazil were investigated to determine whether there is a correlation between the lithium content of the mineral and the colour of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high grade ore zones. It was found that mauve-pink lepidolite associated with pink tourmaline, and brownish lepidolite associated with black tourmaline have high lithium contents, but the colour of lepidolite is not due to lithium. The pink colour of lepidolite and tourmaline is likely to Mn3+, and the brownish tint of lepidolite and black colour of tourmaline to Fe3+. Lepido lites appear to be lithium-rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or-Fe3+.

Jan 1, 1985

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By F. B. Henderson, D. Bird, P. L. Hauff, E. C. Prosh

A National Aeronautics and Space Administration (NASA)-funded project (NASA Grant #NAG13-02026) is underway to determine the ability of hyperspectral remote sensing to map mineralogy that affects water quality within a watershed and to identify the relative contributions of natural and anthropogenic sources to that drainage. Natural sources, particularly areas of pyritic hydrothermal alteration, have been found by the Colorado Geological Survey to be a significant source, sometimes the only source, for acidity and/or metals in a number of areas of Colorado (Neubert, 2000). This situation undoubtedly occurs in many places in the Western United States and elsewhere where metallic mineralization occurs. Anthropogenic sources arise from mining and other human activities that increase the exposure of acid-generating materials to weathering processes, thereby increasing acidity and metal loading to drainages where that activity is occurring or has occurred. This project is attempting to determine if these sources can be differentiated through mineralogical analysis, in conjunction with surface water chemistry that controls the precipitated minerals, of the impacted drainages by remote sensing techniques.

Jan 1, 2003

By K. Takahashi

The methyl stretching vibrations for a series of normal and iso xanthates were determined using an infrared spectrophotometer, and the results were compared with the published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, and solubility appear to be related to the induced polarity of the alkyl groups.

Jan 1, 1968

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By G. Ferrara

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense medium separation systems, the following studies were made: (1) study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV); (2) study of the behaviour of suspensions of magnetite and ferrosilicon in water in both separators. It was found that: (a) the tangential velocity profiles differ in conical and cylindrical vessels: in a conical cyclone free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e. that of a centrifuge; (b) the conical vessel manifests higher centrifugal acceleration and very strong densifying; the density differential, and hence the density gradient inside the vessel is large; (c) the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e. low density differentials, and hence, the density gradient inside the vessel is small; (c) due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while in cylindrical vessels the density cut-point is closer to the medium density. The results provide an interesting description of the differing behaviour of conical and cylindrical vessels and help explain the differences in performance between the two types of separators.

Jan 1, 1998

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

By L. M. Nuelle

Rare earth element (REE)-and gold-bearing breccia pipes are a potentially significant economic target in the Pea Ridge iron ore mine, Washington County, Missouri. The Pea Ridge deposit is one of eight known volcanic-hosted iron ore deposits in the Middle Proterozoic St. Francois terrane, which are similar to the Olympic Dam-type deposits of Australia. The iron orebody is steeply dipping, tabular-shaped, and cuts across the host rhyolite. The footwall of the deposit is zoned from the massive apatite-bearing magnetite core outward to heterolithic breccia, pseudobreccia, specular hematite zone, to an extensive silicified zone. The hanging wall is zoned from the massive magnetite core outward to a heterolithic breccia, pseudobreccia, and an amphibole skarn zone. The REE-rich breccia pipes cut through the various lithologies along the footwall at or near contacts. They are typically 60 m long, 15 m wide, and extend at least 120 m vertically. The pipes are comprised of fragments of rhyolite host rock, massive magnetite zone, specular hematite zone, and silicified zone rocks supported in a matrix of rock flour, barite, feldspar, monazite, apatite, chlorite, xenotime, and, locally, gold. Total REE oxide content of samples of the ground mass material, which are not diluted with lithic fragments, average about 20 weight percent. Grades from working faces in the mine are lower and average about 12 weight percent. Gold distribution is erratic, but concentrations are as high as 371 parts per million.

Jan 1, 1991

By Frank E. Dalton, Forrest C. Neil

INTRODUCTION The Tunnel and Reservoir Plan (TARP) (Figure 1) was adopted in 1972 as the most cost-effective way to bring Chicago area waterways up to Federal and State water quality standards. TARP will significantly reduce pollution of these waterways and provide flood relief for Chicago and 53 adjacent suburban communities. These communities, covering an area of 971 sq km (375 sq miles), are at present served by combined sewers, which carry both raw sewage and stormwater. Because porous ground surfaces have been covered over in recent years by buildings, streets, and parking lots, stormwater runoff into sewers frequently exceeds the capacity of the sewers. When this happens, sewers back-up into hundreds of thousands of basements, and the overflows on the combined sewers discharge rainwater mixed with raw sewage directly into the area's waterways at 645 overflow points. The result is severe pollution of the waterways and flooding in 53 communities. During particularly heavy rains, overloaded rivers have to be relieved by opening the locks and allowing the polluted waterways to flow into Lake Michigan, the region's water source. Goals of TARP 1. PREVENT BACKFLOWS INTO LAKE MICHIGAN. 2. ELIMINATE WATERWAY POLLUTION CAUSED BY COMBINED SEWER OVERFLOWS. 3. PROVIDE AN OUTLET FOR FLOOD WATERS.

Jan 1, 1981

By T. F. Tomb

on' January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure 'limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

By Norman D. Harte, George W. Holl

The development of the most important tool used in Site Testing is reviewed briefly and the application of the information gained is described. The operation of Site Testing and pregrouting of underground excavations is dealt with in detail. Practical experiences (and pitfalls into which the inexperienced might fall) are recorded. But for the application of Site Testing and grouting of shafts, tunnels and other excavations, vast areas of the present goldfields in South Africa would remain unexploitable.

Jan 1, 1981

By Paul E. Richardson, Edwin E. Maust

Cyclic voltammetry and surface potential (photovoltage) measurements have been carried out on galena electrodes in sodium tetraborate solutions with added HC1 and NaOH to adjust the pH over the range 2 to 13. The first technique shows that the surface species formed on moderate anodic polarization and reduced on subsequent cathodic polarization are the same over the entire pH range. At anodic potentials, a soluble metal species and excess sulfur are formed; at cathodic potentials, sulfur is reduced to a soluble species. More importantly, excess surface sulfur is formed spontaneously under zero current conditions in alkaline solutions. This has been shown to occur on both polished surfaces and on virgin surfaces produced by in situ cleavage under the electrolyte. The photovoltage gives some insight into the charge and potential distribution at the galena surface. This is found to depend on past electrochemical history and the n- or p-type semiconducting character of the electrode and is interpreted in terms of changes in the surface stoichiometry that occur during reduction or oxidation. The effect of surface stoichiometry on subsequent xanthate interactions is discussed.

Jan 1, 1976

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010