Search Documents

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By D. E. Piggott, B. E. Hartmann

The thought of constructing an intake shaft five miles from the shore and 142 feet below the surface of Lake Huron from the bottom up sounds like a questionable venture. Why would one want to raise a shaft from the bottom at the end of a 16 foot diameter, six mile long tunnel to within six feet of the bottom of Lake Huron? The answer lies in the fact that Lake Huron is seldom a tranquil lake. The construction period and workable days from the surface are limited. Two previous attempts to construct this intake shaft by conventional means had been thwarted by lake storms. These approaches were circular sheet-piling cofferdams with the intention of sinking a 30 foot OD, five foot wall thickness concrete casing in the center. However lake storms, particularly in the months of November and December, proved disasterous. The last attempt was halted in December 1970 when three of the seven circular cofferdams on the north side were destroyed by pounding waves. Then, due to the nature of the technical difficulties and limited construction schedule time, it seemed desirable to devise a way in which construction could proceed without being too lake-sensitive. Obviously, if men could work from the tunnel and proceed upward toward the bottom of the lake, not having to worry about the soil collapsing and bringing the lake in on their heads, the construction would be unimpeded by adverse weather. The answer to this, however, required techniques beyond the ordinary. Approximately two years previous to the start of this shaft, nine shafts had been efficiently constructed on the same project site

Jan 1, 1974

By Bruce E. Nesbitt, Paul G. Lhotka

At Lupin mine gold is spatially and genetically linked to zones of hydrothermal alteration in iron-formation which are symmetrically developed adjacent to late Archean quartz veins. Immediately adjacent to the veins, coarse grained, typically gold- and sulfide-poor, calc-silicate rocks are often present. These rocks comprise hedenbergite + quartz ± grossular garnet ± epidote ± scheelite ± calcite. Sulfides (pyrrhotite, arsenopyrite and loellingite) and gold are concentrated in the next zone and occur with hornblende-rich rocks comprised of hornblende, quartz, hedenbergite and grunerite. Furthest from the veins are gold- and sulfide-poor, grunerite-rich iron formation comprising grunerite, quartz, hornblende and sometimes magnetite. Although the alteration assemblages have similarities with skarns, they develop in iron formation, and are at best indirectly related to intrusive igneous rocks. Geological and geochemical data clearly indicate the calc-silicate rocks are metasomatic in origin.

Jan 1, 1990

The day after I reached New York, on January 30th, John Ryan of Anaconda told me where they wanted me to go. Late in 1916 the Russian Czar, desperate for money and supplies with which to carry on his unhappy share In the first World War, sent emissaries to the United States to see if our great mining companies might be interested in trying to find mines and to bring them to production in the millions of acres of the Imperial Estates in Russia and Siberia. It looked like a long chance as no one knew whether or where there might be important ore bodies. Even if they found them it might be a hopeless task to equip them under wartime conditions But the American copper companies had plenty of money and they were used to taking risks. They made a supersecret agreement with the Czar's deputies to send an exploring expedition to Russia at once I never learned the names of the other companies but Anaconda was to man- age the venture. Horace Winchell, then the leading mine geologist In the United States, was to be in charge of operations. Charles Janin, an eminent placer and dredge expert, was to study chances for producing gold and platinum. Though at 33 years of age I was much younger than the others, I was chosen to hunt for copper and other valuable metals. Charles Boynton, a business man who had lived in Russia and had married an attractive Russian woman, was to join the party and carry on any necessary financial or diplomatic affairs. He had gone on ahead to arrange for our reception Finally a graduate student from Ann Arbor named Steinberg was to go along as Interpreter. We soon found out that if his Russian was no better than his English his interpretlng couldn't be trusted too much I knew nothing about the millions of square miles In Russia and Siberia, and even less about what mineral deposits might be found, but I was delighted at the prospect. I was treading on air for the few

Jan 1, 1976

By V. K. Kollipara

Dust dispersion characteristics in mine airways are important for developing engineering controls for dust and explosions. Authors here have used CFD modeling approach to analyze the dust dispersion characteristics in mine airways. The technique was initially validated with the published field experimental data. The results obtained were in a reasonable agreement. CFD validation results show that in a single entry the dust concentration decreases exponentially as a function of distance. Finer particles can travel up to a distance of 350-400 m away from the source. Parametric studies indicate that air velocity and input dust concentration has significant influence on dust concentration distribution. CFD modeling was then applied to study the dust dispersion characteristics in a room-and-pillar mine layout. Preliminary results show that dust concentration distribution is highly dependent on the airflow patterns and air velocity distribution. The distribution is not exponential until the velocity in the travel way becomes uniform. Data developed in this study may be used to design mine layouts and engineering controls for dust control and explosions.

Jan 1, 2011

By Scott G. Britton

In this chapter, I shall discuss railroad con¬struction for modern underground coal mines. Because men, materials, and supplies are being moved more often and farther by rail, the ef¬ficient and safe construction of the system takes on new importance. Most large coal mines are opting to use track haulage over other support transportation systems because of cost, ease of installation, reliability, and other factors. En¬gineers tackling the problem of designing such a transportation network must be aware of all the steps required for an effective transportation system design. This chapter discusses all aspects of efficient trackwork construction. The areas covered in¬clude design factors, laying the track, installing turnouts and switches, and installing trolley wire. Each area includes a description of the steps needed to complete the work.

Jan 1, 1983

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By Carl E. Nelson

Shallow epithermal stockworks hosted by maar eruption craters contain over ninety percent of the bulk mineable gold identified to date in the Circum-Caribbean region. Pueblo Viejo (Dominican Republic) and Santa Rosa (Panama) contain combined gold reserves of over 600 tonnes. Bulk mineable gold deposits are also being discovered in and around veins that were formerly mined underground. Bellavista, El Recio and San Martin (Costa Rica) contain combined announced gold reserves of over 50 tonnes. Representative rock suites collected at 8 bulk mineable gold deposits include 291 samples of veins and vein stockworks, hydrothermal eruption breccias, sinter, variably altered host, unaltered host, nearby intrusive rocks and basement. Analyses completed to date show that Circum-Caribbean epithermal ores are enriched in arsenic, mercury and antimony as well as gold and silver. Exploration efforts in the region naturally focus on districts with past production. However, an order of magnitude more bulk mineable gold has been discovered in shallow epithermal stockworks outside of the old bonanza vein camps. Exploration guides include basal island arc volcanic sequences, hydrothermal and hydrovolcanic (maar) eruption breccias, thinly-bedded carbonaceous maar sediments, and hot spring-related silicification and argillic alteration.

Jan 1, 1990

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979

By Harry R. Asche, Manfred K. Lechner

The Cross City Tunnel comprises 2km of a new underground traffic route in Sydney, Australia. The route is very complex, involving some six separate tunnels and three underground Y-junctions. For almost 200m the six tunnels run parallel at different level sunder William Street, Sydney. Almost all of the route runs adjacent to the City Business District of Sydney and adjacent to or below many major buildings and services. The planning and design of this project is described. The geometric arrangement is achieved with a strong dependence on 3D road design packages. Road alignment constraints include land acquisition and proximity to existing tunnels and basements as well as maintaining separation from the other tunnels in the scheme. Geotechnical and hydrogeological studies are described. Findings discussed include the high horizontal stress field in the Sydney area and investigation of incised palaeochannels on the route. Methods of design for the tunnels and Y-junctions are described, as well as methods of settlement prediction for the buildings and services. The latter includes the settlement assessment for more than 200 buildings, many in excess of 20 storeys, as well as services including all of the city railway lines in Sydney.

Jan 1, 2003

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992

By C. Patrick, D. Puckett

The feasibility of monitoring the locations and vital statistics of equipment and personnel in surface and underground mining operations has increased with advancements in radio frequency identification (RFID) technology. This paper addresses the use of RFID technology, which is relatively new to the mining industry, to track surface equipment in mine pits, loading points and processing facilities. Specific applications are discussed, including both simplified and complex truck tracking systems and an automatic pit ticket system. This paper concludes with a discussion of the future possibilities of using RFID technology in mining, including monitoring heart and respiration rates, body temperatures and exertion levels; monitoring repetitious movements for the study of work habits; and logging air quality via personnel sensors.

Jan 1, 1999

By J. R. Walls

Mining is one of world's oldest industries. Its rich history continues into modern times. The Waste Isolation Pilot Plant (WIPP) located in southeastern New Mexico is writing the next chapter in mining history. In fact, WIPP technology is the key to closure of the nuclear cycle with the disposal of nuclear waste in a deep geological repository. It might seem odd that the age-old institution of mining would be linked to the problem of nuclear waste disposal. In fact, the nuclear industry would not exist without mining. Uranium ore is mined from either underground or surface mines as the initial step in harnessing the magnificent resource of nuclear energy.

Jan 1, 1996

By T. M. Barton

This paper presents several case studies in which a mechanics-based boundary-element program is used to back-calculate the surface subsidence associated with various panels at several northern Appalachian coal mines. The program used in this case study is called LAMODEL, which incorporates a frictionless, laminated overburden into a general-purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin-seam or vein-type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from this work show that the LAMODEL program is not as accurate as available empirical subsidence-predictive methods; the expected correlation between the geology and the optimum input parameters is not evident. However, for a mechanics-based program, LAMODEL does provide moderately accurate subsidence calculations, and it is one of a few programs that can even attempt to practically calculate both underground stress and convergence and the resulting surface subsidence.

Jan 1, 2000

By John G. Whellock

Over the last decade new constraints have emerged in the metallurgical industry which challenge the very basis of design and construction of smelters and refineries. The hackneyed designs of the past will not now serve the revised objectives of: - minimal cost of ownership - improved productivity - reduced energy consumption - greater flexibility in feed or product - minimized recycle loops and by-products - more stringent environmental control The impact of these constraints has been channeled constructively into process intensification - exemplified at the large scale by the introduction of flash smelting technology and at the smaller scale by the application of rotary process vessels and converters for augmented heat and mass transfer. The design of successful process plants depends on the understanding of the unit operations and their interactions which is the discipline of systems engineering. With the advent of increased process intensification the importance of a systems approach to process design and implementation becomes paramount. This paper describes the systems approach with specific reference to medium scale projects in the primary and secondary metallurgical industry.

Jan 1, 1985

By Laurence M. Demers, Douglas C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology which results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoids) have been implicated as important biochemical mediators of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dub1 could influence the production of pro-inflammatory mediators in the lung environment. Rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500°C and 1100°C. Prostaglandin E2 (PGE2) and thromboxane B2 (TxB2) levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 and TxB2 production were markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE2 and TxB2 production. In vitro exposure of AM to untreated silica resulted in a significant increase in PGE2 and TxB2 production compared to control. However, exposure of AM to silica calcined to 1100°C resulted in eicosanoid levels which were not significantly different from control. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production.

Jan 1, 1991

By Derek M. Hutchinson, Don Zeni

The construction of shafts by blind drilling has been made cost effective by advances in technology and experience. The techniques of blind shaft drilling are discussed and a brief history presented. A recent use of blind shaft drilling to access a small gold ore body in Australia is described. Finally, the most recent developments in drilling machinery are reviewed together with possible applications in new and existing mines.

Jan 1, 1987

By Daniel W. H. Su

The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate post-mining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects.

Jan 1, 1986

By James S. Redpath

INTRODUCTION Background Early in 1972 our firm was asked by Cominco, managers of Arvik Mines Limited, to carry out an underground exploration programme referred to as the "Polaris Project" on a zinc-lead deposit in Canada's High Arctic. We had carried out numerous projects in the far north but this was to be the first long decline driven in perma-frost. Despite the short notice it was possible to meet the quickly approaching summer shipping deadline. We were able to do this by drawing heavily on our own and Cominco's background in Arctic operations. The project was an excellent example of owner-contractor co-operation and this spirit was responsible for the success of the project. Unusual Aspects There were a number of unusual aspects of the Polaris Project which are discussed in this paper. The extremely remote location, the short shipping season, and the fact that the work was carried out in permanently frozen ground, when combined with the lack of handy fresh water and a very severe climate, make it unique in many respects. Despite these handicaps, a record was set during the driving of the exploration decline.

Jan 1, 1974

By M. Menegaki

Restoration of abandoned mine sites is still one of the weak points of mining practice. The latter stands especially for the case of the surface coal and lignite exploitations, where the extended size of the disturbed land and the drastic changes to the geomorphologic features do not facilitate the implementation of a cost effective and environmentally sound reclamation plan. The paper examines the parameters involved towards the legal requirements for the reclamation of the first lignite exploitation in Greece, namely the ?Plakes? mine, located at Euboea, due to the particularities of the site. Then an integrated redesign procedure is presented, aiming at minimizing aesthetic degradation, confronting technical difficulties and preparing the site to accept new uses.

Jan 1, 2005