Search Documents

By R. P. King

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture characteristics of a number of single and multiphase brittle materials has been investigated using the Ultrafast Load Cell. It has been observed that very significant reductions in both fracture energies and the material integrity (damage) were achieved by heating followed by water quenching.

Jan 1, 1995

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By K. C. Vories, C. D. Elifrits, F. F. Haston

The required reclamation of land disturbed by surface coal mining often results in the creation of some oversteepened slopes that are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has shown that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations are summarized in this paper, and field results are shown.

Jan 1, 1987

By P. S. Parobeck, T. F. Tomb, R. S. Ondry

From October 1980 through August 1982, surveys were conducted on 19 longwall mining operations to obtain data relative to respirable dust levels associated with particular longwall operations and occupations, to make recommendations for enhancing dust control, and, where applicable, to evaluate the effectiveness of new technology implemented to control dust. The paper summarizes the data collected during these surveys and, where possible, draws conclusions and discusses actions that can be utilized to reduce exposures to respirable coal mine dust on longwall mining operations.

Jan 1, 1987

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

By K. S. Eric Forssberg, T. V. Subrahmanyam

The present paper deals with the important technological developments in gold processing and where possible, the data is presented in the form of tables. Gold processing methods have evolved to such an extent that low grade and complex ores once considered uneconomic are now becoming viable. Constant efforts are underway to innovate technologies in order to improve the efficiencies and cut down the capital and operating costs. The methods are discussed.

Jan 1, 1988

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981

By R. L. Loofbourow, Robert R. Miller

Deep, stable, unlined space promises secure, efficient, acceptable solutions to several current problems. With truly favorable conditions, it can be economic as well. The basic requirement is sufficient sound, tight rock at required depth. This and unusual surface requirements point to special testing. An objective is to describe conditions for planners, estimators and contracts. A first stage concept study needn't be prolonged but should overlook nothing significant. Although observations and tests on core are considered essential, time and expense can be cut by supplementing then with tests on walls of rotary or percussion holes. In some places initial drilling could be shallow.

Jan 1, 1981

By George W. Toth

This chapter describes the development of a computer code which rapidly estimates the cost of producing coal from either surface or underground mining situations. The computer code, termed the coal production cost (CPC) code, was developed under an NUS corporate research grant and was based on the findings of several coal mining and cost research analyses performed by NUS over a three-year period. The studies which served as the primary basis for the CPC code were the coal mining cost models developed by NUS for the Electric Power Research Institute. These models were designed for use in manual analyses and have been published by EPRI (Toth, 1977; and Stinnett, 1977).

Jan 1, 1979

By Paul Gribbon, Greg Colzani, Jim McDonald

The $300 million West Side Combined Sewer Over?ow Project consists of over5.5 kilometers of soft ground tunnel, an 833-million liter per day (220-MGD) deep shaft pump station, 3 kilometers of micro tunneling, and other miscellaneous shafts and pipelines. The construction contract, underway since September 2002, is a reimbursable cost plus fixed fee contract that included a quali?cations-based contractor procurement process and has undergone some modi?cation since execution. This paper will describe the contractual issues addressed to date, dispute resolution, where improvements can be made, and how an Owner can evaluate whether this type of contract is the best approach for an underground project.

Jan 1, 2005

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995

By C. O. Brawner

Geotechnical theory is reasonably well developed to evaluate the stability of rock slopes for surface mining projects. It is recognized widely that structural geology, groundwater pressures and seepage, and blasting are key factors that influence the stability of such slopes. However, our capabilities to model the structural geology, to determine rock strength along discontinuities and to model groundwater pressures and profiles are still very approximate. Plus, practical experience of the rock mechanics engineer is one of the most important inputs to the design of open pit mine slopes. To emphasize the use of practical experience, a number of case examples are reviewed here to illustrate key factors that must be evaluated. These case examples comprise a continuation of other examples presented in the Jackling lecture to the SME in 1986 by the author (Brawner, 1986). Example no. 1 In situations where the orientation of geologic discontinuities will not influence rock slope stability, extremely steep slopes can be developed, providing blasting and groundwater are controlled adequately. An excellent example of this condition is the Republic Pit of Cleveland Cliffs in Michigan. The rock slope in Fig. 1 isover400fthigh with a face angle of approximately 80". The rock is hard and massive, and blasting was carefully controlled. The original design of this slope was at45", a standard design angle at that time. The competency of the rock and the lack of critical geologic structure subsequently was recognized, and the much steeper slope angle was developed successfully. The rock proved to be so competent and the slope sufficiently stable that an underground crusher station was developed with entrance and exit tunnels excavated at the toe of the steep wall.

Jan 1, 1991

By Thomas A. Wheeler, Robert O. Keys

The choice of the flotation reagent that suits a particular coal has become more complicated with the development of new, more efficient reagents. Frothers and conditioning reagents, in particular, have experienced a dramatic reevaluation of their role in floating various types of coals. This paper offers a better understanding of how each of the following factors contributes to the reagent selection: 1. Natural Flotability 2. Degree of Oxidation 3. Size Distribution 4. Percent Solids in Feed Slurry 5. Fluctuations in Plant Feed 6. Limitations on Froth Handling 7. Clean Coal Specifications 8. Ash Content in Feed a) discrete ashable minerals b) inherent ashable minerals 9. Water Chemistry 10. Petrographic Composition of Coal 11. Free-Swelling Index 12. Convictions of Customer The application of conditioning reagents - both promoters and emulsifiers can substantially improve the coal recovery. Some low-rank, hydrophylic coal, previously considered unfloatable can be economically recovered with the use of the proper reagent.

Jan 1, 1986

By Michael D. Sopko

This paper describes the project implementation from financing, through the engineering and construction phases, mine and process plant commissioning as well as operating experience realized to-date. The single line flowsheet used to process the lateritic nickel ore to a 75 percent nickel matte is presented with emphasis on the main pyrometallurgical operations. These include a rotary dryer, a unique reduction kiln, a 45 000 kVA electric furnace and two Pierce-Smith type converters. Associated infrastructure facilities and services necessary to sustain the 11 300 tonnes (12 500 short tons) per year nickel production rate are also described.

Jan 1, 1979

By George E. Niewiadomski

The exposure of miners to radon gas and its airborne daughter products is a serious health problem which has long been recognized in the uranium mining industry. The association of high exposure to alpha particle emitters with incidence of lung cancer is well established. There continues to be a pressing need to reduce and eventually eliminate the high incidence of occupational lung cancer among uranium miners through the development of new and improved measurement and control technologies. This paper highlights the current efforts of the Bureau of Mines radiation hazards research program. It is aimed at obtaining a fundamental understanding of the behavior and transport of radon and radon daughters, developing more accurate and reliable instruments and measurement methods and developing cost-effective control techniques. Also discussed are the most recent accomplishments and the future research plans of the program.

Jan 1, 1981