Search Documents

By D. L. Jones, S. Knoerr, J. Mansanti

The Buckhorn Mine in Nevada currently treats oxide ore using heap leach methods, but exploration has identified sulphide reserves which are refractory in nature. Preliminary testwork was conducted on the sulphide material to screen potential pre-cyanidation treatment methods. Processes evaluated included pressure oxidation, biological oxidation, nitric acid oxidation and roasting. An initial economic and process analysis of the results concluded that roasting was the only viable process, and only if the roaster off-gases were converted to soleable sulphuric acid. Further economic analysis indicated that roasting of the whole ore was more attractive than pre-concentrating by flotation, followed by roasting of the concentrate. These results were generalized to show that for high sulphur ore a roaster/acid plant combination is more attractive that either of the other options, ie. pressure leaching or bioleaching, provided the by-product acid is soleable.

Jan 1, 1990

By H. W. Seany

Over the years since the initial experiments with underground concreting were made in 1956, attesting to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the, mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other advantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 1, 1965

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices that minimize soil compaction will produce better results when forestland is the intended postmining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees. Since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree-survival rate. It is believed that these two soil-compaction parameters may ultimately be used to predict tree-survival rates on reclaimed surface mined lands.

Jan 1, 2003

By Chen L. Lin, Luis R. M. Bittencourt, Jan D. Miller

Recently research efforts have been made to obtain a high-purity gibbsite concentrate, suitable for first-class alumina refractories, from a Brazilian bauxite ore containing gibbsite (50%), quartz (35%),and kaolinite (15%). Detailed polished-section microprobe analysis was used to describe the liberation characteristics of the ore. Experimental results suggest that the kaolinite liberation characteristics can be described by King's liberation model and that only about 11% of the kaolinite is expected to be liberated at a particle size of 75 µ. Bench-scale experiments for the flotation of gibbsite/kaolinite from quartz using alkyl sulfates as collectors were particularly successful at pH 2, and under appropriate conditions a concentrate containing 93.0% A1 0 (calcined basis) was obtained 2 3 at a gibbsite recovery of about 96%. Subsequently, the more difficult separation of kaolinite from gibbsite was accomplished by kaolinite flotation from the alumina concentrate with a quaternary ammonium salt at pH 6 to produce a high-purity gibbsite product, 97.4% A12O3 (calcined basis), at an overall gibbsite recovery from the bauxite flotation feed of about 90%.

Jan 1, 1990

By G. S. Brierley, R. D. Drake, J. E. Kelley, J. C. Kellogg

This case study embodies the problems of an underground project under current contracting practices. It will provide a realistic framework for a structured examination of the anatomy of a major complex underground project. Just as it will illustrate the frustrations of the parties to an underground contract, it will also provide a means to examine potential opportunities to provide a better way to develop underground space. Urban Transit Authority (UTA) had planned to expand their heavy rail underground transit system through an extension to an existing line. UTA lacked sufficient funding to guarantee the construction and operation of this planned extension. Venture Partner Associates (VPA) in conjunction with four major department stores entered into an agreement to create a major underground space for a commercial/recreational facility. The concept was to locate the facility adjacent to a planned station and beneath existing aboveground office facilities. This group was known as Commercial Development Corporation (CDC). UTA had reached an agreement with UMTA to provide 20 percent of the line and station costs. UTA then entered into an agreement with CDC to provide the needed additional funding for the station work in return for locating the station adjacent to the planned underground commercial/recreational complex. The agreement called for CDC to contribute 20 percent to the station cost to a maximum of $25 million plus a one percent contribution from commercial/recreational revenues for operating costs.

Jan 1, 1989

By R. C. Bryan, D. B. Jamison

This paper describes a procedure for minimizing the operational costs associated with blending sodium in coal at a surface mine in the Powder River Basin. Mine site blending is performed by adjusting daily production rates for high- and low-sodium pits. These adjustments are designed to produce a consistent sodium value called the blending target. The mine's contractual limit for sodium is sufficiently close to the field average value that any decrease in the sodium blending target may result in an opportunity cost, if the number of potentially minable tons is reduced. Conversely, any increase in the blending target may result in a higher sampling cost if more information is required to keep the blend within contractual limits. Blending parameters were defined using a geostatistical block model of sodium content that was based on analyses of hundreds of in-pit sample holes. Variograms for these data were used to compute the marginal costs of opportunity and sampling for a series of hypothetical in-pit drilling patterns. These marginal costs provided a basis for selecting optimum values for key parameters such as the blending target, production variance and in-pit sampling density. The benefit of implementing these optimized parameter values is that operational costs of sodium blending will be minimized over the long-term. At the mine where this procedure was developed, each dollar spent to increase the sampling density to the optimum value was shown to generate a $10 savings in opportunity cost.

Jan 1, 1991

By Richard Switalski, Mark R. Kritzer, Boro J. Lukajic, Robert Pintabona

Ground freezing was chosen as an initial support method during construction of two deep shafts at the Mill Creek project. The Mill Creek, Phase 2 tunnel (MCT-2) is utilized to convey and store combined storm and sanitary sewage collected from the member communities in the greater Cleveland area. The main objective of groundfreezing was to provide a strong support structure to resist soil and groundwater pressures. This was achieved by creating a watertight, frozen-ground barrier around the shaft perimeter. The paper will provide an overview of ground freezing techniques applied during the construction of two shafts, each 250-feet deep.

Jan 1, 2003

By R. M. Imhof, M. J. G. Battersby, J. V. Brown

There is a plethora of former industrial sites where coal mining operations have left large slurry impoundments. These contain raw washed fines, which have previously been too expensive to process to requisite grades for commercial use. New technology has been developed for fine material processing, namely the Imhoflot pneumatic flotation G-Cell. This froth flotation technique is a highly efficient means of concentrating coal and is particularly appropriate to the nature of materials encountered in tailings ponds. The high volumetric throughput resulting from the vastly reduced residence time in the cell allows for drastically reduced equipment sizes when compared to conventional flotation cells. This means the process, when combined with innovative pre treatment and filtration equipment can be developed as a mobile plant concept. This is seen as a minimum requirement when re-treating and rehabilitating fine coal ponds.

Jan 1, 2003

By T. B. Whitmoyer, J. E. Sneckenberger, M. A. Jerabek, C. F. Stanley

The measurement of acoustic impedance at frequencies up to 6,400 Hz has been proposed as a diagnostic tool to yield more detailed information about lung condition. A three generation branching system of plastic Y-tubes has been constructed. The impedance of the branched system is measured by an impedance tube using the two-microphone technique. The impedance spectrum is used to calculate the reflection coefficient spectrum, which is converted to an impulse response by an inverse FFT. The area function is extracted from the impulse response by the Ware-Aki algorithm. Measurements of acoustic impedance of the branched system were made for several different end conditions of the eight terminal outlets. The outlets were either blocked with modeling clay, plastic packing material, or aluminum blocks or were unblocked. Six measurements were made of each configuration. In general, the more outlets blocked, the larger the shift to the right of the impedance magnitude peaks for frequencies above 3000 Hz. The impedance magnitude peaks for the plastic packing material were shifted in frequency to the right relative to the peaks of the other system terminations. The impedance magnitude peaks for the clay and aluminum system terminations were significantly different in magnitude but not shifted in frequency. The area functions at the end of the branched system were significantly different (a > 99%) for most of the end conditions. Area functions for the modeled branched lung systems between the end of the impedance tube and the termination outlets of the branched system were similar but distinctively different for the various end conditions. These results indicate that the two-microphone technique can sense small changes in the terminating end conditions of a rigid system of branched tubes and thus may sense impedance changes due to lung disease in the conducting airways. Keywords: acoustic impedance, lung model, area function.

Jan 1, 1991

By Liguang Wang, Roe-Hoan Yoon

The thin film balance (TFB) technique was used to measure the equilibrium film thicknesses (H3 between two air bubbles in sodium dodecyl sulfate (SDS) and electrolyte (NaCl) solutions. The results were used to determine the magnitudes of the hydrophobic forces (K232) using the extended DLVO theory. The Km values determined from He measurement allowed us to predict disjoining pressure isotherms, which were found to be in excellent agreement with those obtained experimentally using a bike-wheel film holder. The rate of film thinning was measured at low SDS concentrations with varying amounts of electrolyte (NaCl) added. In general film thinning was controlled by the capillary pressure during the initial stages, while it was controlled by the surfaces forces during the later stages. At low NaCl concentrations, it was possible to predict the rate of film thinning using the Reynolds equation, provided that the driving force was corrected for the contributions from the hydrophobic force, which in turn were determined from the KZ32 values obtained from the He values measured experimentally. At high NaCl concentrations, where it was difficult to measure the equilibrium film thicknesses, the contributions from the hydrophobic forces were determined by fitting the film thinning data to the Reynolds equation. The K232 values obtained using both the equilibrium film thickness and the film thinning measurements showed that hydrophobic force deceased with increasing surfactant and salt concentrations. It was found that the hydrophobic force in foam films was very sensitive to the added electrolyte concentration.

Jan 1, 2005

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By Anshumali Gangwar

This paper outlines the chance constrained binary integer program developed by the author in his doctoral dissertation at Columbia University, New York, 1973. The optimum planning of a mining program involves the determination of a production schedule which maximizes the net present value of the mining property. The actual mining process has an inherent stochastic and discrete nature. In particular, the demand for the mined product and the grade of the mineralized material in the ore are the two most important stochastic mining variables. The decision to mine or not to mine any block of a mining property is a binary integer variable. This paper outlines the formulation of pit production scheduling problem as a chance constrained binary integer program. The deterministic equivalents of these chance constraints are nonlinear in binary variables which have subsequently been linearized. The planned objective is to meet with a stipulated high degree of reliability, all the random demands as they materialize with a random supply of the commodity being marketed as determined by the eventuating random grade values of the exposed ore blocks and the mining system's production constraints such that the discounted total production costs over the entire planning horizon are minimized or the profits maximized. The emerging surface of the mine in each scheduling period is determined by the values taken by the binary decision variable associated with each block of material in each scheduling period.

Jan 1, 1982

By Gregg E. Korbin, Patrick Hamilton

INTRODUCTION The Balsam Meadow Project, presently under construction for the Southern California Edison Company, is located approximately 55 miles northeast of Fresno, in the Sierra Nevada Mountains (Fig. 1). Major components of this project include an underground powerhouse for a 200 MW unit and a high pressure power tunnel/shaft. Site exploration [ ]

Jan 1, 1987

By Q. X. Yun, S. H. Liu

This paper provides a new approach to determine the opening layout in underground mining methods by means of genetic programming. Based on a set of random combination of openings, the layout of openings will gradually improve with the help of genetic operations, including reproduction, crossover, mutation and fitness calculation. The optimal solution will finally emerge according to Darwinian principle: "the survival of the fittest ".

Jan 1, 2002

By H. J. Chen, Y. Luo, S. S. Peng

Surface subsidence resulting from underground coal mining can cause problems for buried pipelines. In this paper, a technique for assessing the level of stress on a subsidence-affected pipeline is introduced. The main contributors to the stress are identified, and mitigation techniques for reducing the stress are proposed. The proposed mitigation techniques were then successfully tested.

Jan 1, 1998

By Yong Kang, Renhuan Yu, Xinquan Liu, Liangying Chu, Qian Luo

In grinding-classification circuit, overgrinding, resulted from the fact that hydrophobic materials have higher density than hydrophilicmaterials, has been known as a knotty problem. By using of the air-sparged hydrocyclone (ASH) as classifier, in this pair, the overgrinding of hydrophobic materials has been successfully minimized. Compared with the conventional hydrocyclones, the ASH has less fine hydrophobic particles in the underflow and less large particles in the overflow, which shows that the recovery of fine hydrophobic particles in the overflow has been improved in the ASH.

Jan 1, 1995

By Corneille S. Ek

Flotation of several copper and lead-zinc ores has been carried out with mercaptobenzothiazole (MBT) as promoter. The results of laboratgory batch flotation tests have been compared with those obtained when using more common collectors like xanthates or dithiophosphates. It generally appears that MBT is an effective collector of all the sulfides, including pyrite, but that high selectivity is rather difficult to attain, except for gangue drop-out. Some kinetic tests have been performed to check the froth production rate by MBT as compared to other collectors.

Jan 1, 1995

By James R. Fahy, Lawrence A. Hansen, J. David Deatherage

A laboratory testing program was con- ducted to investigate the shear strength along specific soil-liner interfaces for five types of liners of varying thicknesses. Results indicated a bilinear relationship between shear stress and applied normal stresses ranging from 276 to 1000 pKa (40 to 145 psi). Friction angles along the soil- liner interface below the break point normal stress (7.5 to 19 degrees) were lower than those recorded above the break point normal stress (14.5 to 39 degrees ).

Jan 1, 1987

By S. J. Jung, F. Lock

This research came about because of the recognized need for a safe, easy way to line small-diameter bored raises (less than 150 cm). Currently, an operator must go down the raise and apply the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small-diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1995

By D. I. Phillips, P. J. Bethell

This paper focuses on the -1/2 mm cleaning at Elk Run Coal. The original circuitry incorporated desliming cyclones. Problems with slimes entrainment in the cyclone underflow (froth cell feed) resulted in poor froth cell selectivity. Laboratory test work led to the installation of high frequency desliming screens. Consequently, great improvement in cell performance was brought about by enhanced desliming with the ability to use split flotation. The modifications resulted in significant improvement in total plant performance and overall yield while maintaining clean coal quality.

Jan 1, 1987