Search Documents

By R. W. Bartlett

Aeration curing, over- a long duration in wet- red stockpiles, shows promise as an affordable pretreatment method for oxidizing gold encapsulating sulfide minerals, and possibly organic matter, in low grade refractory ores. Following aeration pretreatment, the ore is reclaimed, neutralized, and cyanide leached by conventional practices. Large tonnages of subeconomic material, including mine stripping waste, may he converted into ore by this new technology. The results presented show that a successful application of this technology will likely require crushing to about -2 cm (-3/4 in.), followed by aeration in a wet stockpile for long periods, up m three years. Natural convection may he inadequate, hut forced air ventilation, at modest pressures and power consumption, is affordable.

Jan 1, 1991

By I. E. Zevgolis

A comprehensive critical review on the subject of sulfates-induced swelling behavior of lime-treated soils is presented in this study. Starting with the description of a well documented case study, the mechanisms behind the swelling behavior and the factors that affect this behavior are discussed. Then, the major experimental methods of sulfates content determination are briefly presented. Finally, an attempt is made to categorize sulfates level and equivalent risk for civil infrastructure. The paper indicates that limited work has been done, not only on identifying safe conditions for use of chemical stabilizers in presence of sulfate rich soils, but also on developing materials and methods to avoid, or at least mitigate, the problem.

Jan 1, 2008

By W. Swisterski, G. Romaniszyn, S. A. Lukasiewicz

The present paper analyzes the motion of a particle of material in a horizontaly rotating tumbling mill. The sliding of the particle under action of dynamic and friction forces and its free flight fall are analyzed. It was found that mechanism of free-fall occurs at supercritical rotations of the mill.

Jan 1, 1991

By V. Rajaram

V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 1, 1987

By William J. Douglas

Defining Productivity Productivity is a principal concern to all organizations - industrial, commercial, government, and academic. As a ratio of output to input, productivity measures the efficiency of an industrial process, much as thermodynamic efficiency measures the useful work obtained from the available energy consumed. However, there is one important difference. Whereas thermodynamic efficiency is a dimensionless a ratio of energies, productivity output and input are usually measured in different physical units. Nevertheless, the resulting ratio is a normalized expression for unit of output per unit of input to the process. In the early days of coal, mining was essentially a hand loading operation. There was little expenditure of alternative forms of energy within the process. Loading required expenditures of human energy on the order of 1.2 MJ/t (1,000 Btu per st). And if we accept the conventional value "you load 16 tons," the output to input ratio is 14.5 t (16 st) per manshift. In energy terms, it is on the order of 116 MJ/t (100,000 Btu per st) produced per labor Btu expended. However, the latter measure of efficiency was not meaningful in economic terms, while the 14.5 t (16 st) per manshift was significant. Since labor was the principal component of cost, it represented a direct relationship to the cost of production: [ ] Furthermore, when workers were paid directly on the basis of tons produced, the labor cost per ton was specified directly by this rate. With the introduction of mechanized loading, significant increases in productivity occurred, when measured on the basis of tons per manshift. Electric power consumed about 11.6-116 MJ/t (10,000-100,000 Btu per st). This makes the 29-GJ/t (25 million Btu per st) coal output/input ratio between 100 and 1,000. That is one or two orders of magnitude lower than hand loading. However, electric energy was quite inexpensive compared to labor, which made the mechanization economically efficient. The accepted productivity measure continued to be tons per manshift. This measure includes some of the effects of mechanization: namely, the additional manpower needed to maintain the machines and support the equipment that uses electrical energy. However, it does not consider the capital and operating costs that relate to mechanized equipment. As a result, the concept of tons per machine-shift has emerged as an accepted measure of shift productivity. The only appropriate measure that encorporates the productivity of men and machines is an economic one. The output is the tonnage per shift and the impact is the cost per shift. [ ] This is simply the inverse of the cost per ton. In addition, much flexibility is available in allo¬cating costs to the three categories. This adds a level of intangibility to the measure. The amount of information needed to obtain all of the required costs is appreciable compared to the simple matter of counting tons and workers. Furthermore, financial information relating to production costs is closely held by mining companies, so historical statistics on economic productivity are not publicly available. To extend the concept further, consider the value of the tonnage produced, to obtain a dimensionless ($/$) measure of economic productivity.

Jan 11, 1983

By Tore M. Larsen

The Rødsand Gruber mining company is a subsidiary of the Norwegian industrial corporation Elkem AS, and its mine is situated in the northwestern part of southern Norway. The ore from this mine is a relatively low grade, magnetite ore with a small amount of vanadium. The ore bodies are very irregular in shape, resulting in a high amount of waste rock intrusion in the stopes. The annual underground production in the mines is approximately 1 million t. Because of varying dimensions of the ore bodies, both transverse and longitudinal stopes are employed. The inclination of an ore body is usually 1.04 to 1.59 rad (60 to 90°), and the horizontal width varies up to 100 m. Sublevel stoping has been the traditional mining methods in this mine. Until a few years ago, the ore was primarily blasted using horizontal blasthole fans drilled from Alimak raises. Recently, however there has been an increasing demand for a les expensive mining method. Alternate systems were considered, and finally a method based upon large blasthole stoping was found to be the most suitable. GENERAL LAYOUT The general layout of a stope is shown in Fig. 1 As with all the figures in this chapter, only the prin¬ciples of the method are emphasized and the details may not be valid for any particular site in the mine. In transverse stopes, the horizontal width of the ore determines the length of the stopes. The average length is approximately 50 m, the width of the stopes is 20 m, and there is a 10-m wide vertical pillar between. The distance between the main levels is 60 m. Usually a horizontal (sill) pillar 10 m thick is left below the mucking level. Each stope is first undercut along the entire stope length. This undercut is made with 50.8-mm (2-in.) diam drill holes in a fan pattern. At the moment this is being done by a trackless Atlas Copco Promec jumbo equipped with two Cop 130 pneumatic rock drills. The drill drift is 4 X 4 m, and the crater is 20 m high. This leaves a 36-m stope height to mine with large blastholes. To achieve a fair portion of vertical drilling withlarge blastholes, there are two parallel drill drifts at the top of each stope. These drifts are 4 m high and 9 m wide, separated by a 4-m wide pillar in the middle of the stope. To ease the drilling of perimeter holes, the drifts extend 1 m into the vertical pillar on each side of the stope. The pillar will thus be only 8 m wide on the drill drift level, but 10 m wide down the rest of the stope.

Jan 1, 1982

By Kenneth K. Humphreys

Over the past four years, the Coal Research Bureau of West Virginia University has presented a number of papers on operations research in the coal industry before various AIME meetings and meetings of other societies. These papers have been followed up by further presentations in the technical press. The emphasis of all of these papers has been to demonstrate applications of operations research to the solution of numerous types of coal industry problems. In each case, effort has been made to demonstrate that operations research does not require extensive knowledge of computer science or use of sophisticated higher mathematics. In fact, for most applications, satisfactory results can be obtained by a single individual in a minimum of time with no aids other than a pencil and paper and a knowledge of basic arithmetic. The most recent efforts by the Coal Research Bureau have been directed toward the continuing industry problem of optimizing the location of mining facilities. Preliminary work in this area was presented before the Central Appalachian Section of AIME and subsequently published in the May, 1972, issue of Coal Age. This initial presentation illustrated techniques for determining optimum locations of facilities based upon material transport effort under the assumption of constant cost per ton mile of haulage effort. The present paper will expand upon this earlier work and introduce economic factors. In the design of a mine or mining system, careful consideration must be given to the sites selected for each element of the system. Optimum placement of facilities is vital to minimize capital and operating cost. Thus, barring unfavorable geological conditions or other exceptional factors, facilities should be located at those points which represent the minimum cumulative cost over the life of the property. Most cost factors are independent, or essentially independent of the location of fixed facilities. Thus, for example, regardless of the location of the shaft, the direct cost to mine any given ton of coal is essentially constant. The major 1

Jan 1, 1972

By Douglas R. Cook

The Ertsberg East discovery was announced by Freeport in 1979 with proven geological reserves of 45 Mt (49.6 million tons) with a grade of 2.65% copper and recoverable gold values. This recently discovered deposit is one of a cluster of skarn-type copper occurrences found within the limits of Freeport Indonesia's mining con- cession at an elevation of about 3600 m (12,000 ft) in the extremely rugged Jaya Wijaya Mountains of Irian Jaya, the Indonesian half of the island of New Guinea. The Ertsberg East lies about 1.5 km (0.9 miles) east of the Ertsberg ore body, which is also known by the Indonesian name "Gunung Bijih" or "ore mountain." For general background, the original Ertsberg ore body was first discovered by the Dutch geologist Jacques Dozy in 1938 while on a mountain climbing expedition. It was mapped and sampled by Forbes Wilson and Del Flint after a two-week harrowing trek into the mountains from the coastal swamps. A drilling program in 1967- 1968 established that the Ertsberg was a viable mining venture, containing approximately 33 Mt (36.4 million tons) of skarn-type copper ore. The deposit averaged 2.5% copper, with significant values in gold and silver. The first shipment of copper concentrates was made in December 1972, following a capital investment of $200 million. Following the routine production of ore from this deposit, it became necessary to consider additional sources of ore to extend the life of the mining operation. An exploration program was thus started with the initial objective of finding shallow or surface ores which could be blended with the material being mined at Ertsberg. Project geologist Frank Nelson was transferred from Freeport Exploration Co. to the Freeport Indonesia organization at the Ertsberg mine. However, the exploration work was the functional responsibility of Freeport Exploration. Del Flint had overall responsibility for the program from the Reno headquarters office and provided liaison with management in the USA and Indonesia.

Jan 1, 1991

By Peter W. Willcocks

The Cyanide Regeneration Process (CRP) was developed by Golconda Engineering and Mining Services and installed at Golconda's Beaconsfield Gold Tailings Retreatment Project situated in Tasmania, Australia. The Tailings Project is a 1000 ton per day carbon-in-pulp treatment plant, feed for which consists of tailings material which is dredged from the Tamar River. The pulp is screened to remove debris, then cycloned to form two products. Underflow pulp is stored in a 350 ton bin and cyclone overflow passes to a thickener. The coarse pulp material is fed to the grinding circuit then rejoins the thickened slimes in the cyanide leach circuit. Gold is extracted by carbon-in-pulp techniques. The plant is sited in rolling, hilly country approximately 200 meters from the Tamar River. The residue disposal area is quite small consisting of four dams, totalling 42 acres. The regional climate is cool and wet with little evaporation; therefore, we anticipated a net increase in contained liquor, and subsequent storage problems. Our plan was to remove cyanide from the liquor prior to returning the detoxified solution to the river system. Such treatment was not required until midway through the second year of the project. Initial testwork on sample material indicated that destruction of cyanide by chlorine was the simple solution. Subsequent follow-up on actual plant liquor indicated a huge chlorine requirement due, we believe, to the substantial degradation of vegetable matter plus organic content from the marine environment. The cost of cyanide destruction could not be justified.

Jan 1, 1998

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By N. R. Joshi, A. D. Agate

It is estimated that more than 80% of phosphate rock output in the world is used for fertilizer production. In India, there are only a few high-grade deposits of phosphate ores; therefore, most of the requirement for phosphatic fertilizers is satisfied with imported DAP (diamino phosphoric acid). Due to the drain on foreign exchange reserves, this import-dependent, essential commodity is in short supply in India and, therefore, is sparingly used by farmers. In addition, of the added phosphorus, normally 80% becomes unavailable to plants because phosphorus complexes are formed in soil, causing deleterious effects on plants. In our laboratory, this problem was tackled by using a bacterial consortium of phosphorus-solubilizing bacteria. It resulted in the speeding up of seed germination and increasing available phosphorus in the soil by 14%, over a period of 80 days. To use the low-grade deposits of phosphatic rocks available in India near Hirapur, Madhya Pradesh, India, which contain high amounts of iron, beneficiation through microbial means was used for phosphorus removal. Beneficiation was achieved partially through removal of extra iron by oxidizing ferrous iron from the ore by a Thiobacillus species after removal of impurities containing both silica and iron, instead of sieving and cleaning the ore using different techniques. This resulted in a cleaner ore, with nearly 70% of such impurities removed. The factors for beneficiation technique were standardized at the laboratory level and are being used for scaling up of the process. Thus, the beneficiation of phosphatic rock from Hirapur will be an important first step of phosphorus production in India.

Jan 1, 1999

By Gerd A. Schroth

For many years, the automatic preparation of samples prior to elemental analyses has become quite common in several indus­tries, including aluminum, cement, non-ferrous and steel. Modem automatic preparation of powdery, granular or metallic samples which initially emerged as leading edge technology, has become state of the art and a proven technology.

Jan 1, 1996

By E. Cetin

The authors describe the general problem of cut-off grade optimisation for multi-mineral deposits and outline the use of genetic algorithms for optimal cut-off grade schedules for deposits with up to three constituent minerals. Case studies are given and a comparison is made with Lane's multi- mineral cut-off grade algorithm.

Jan 1, 2002

By Michael Brittan

Diagnostic regression analysis has been used as a tool to improve the recovery efficiencies of numerous gold mills, yielding significant revenue increases. In the course of the analyses it has generally been found that ore head grade is a statistically dominant variable affecting the overall gold recovery. Higher grades invariably generate higher recoveries. Examples are given from several operations in the world's two largest gold producing countries, South Africa and the United States. The plants considered cover the treatment of both oxide and refractory ores. A simple generalized model is presented relating tails to head grade. Since ore grade variations are beyond operational control, operators should not be held accountable for decreases in recovery caused by lower head grades. Conversely, the ore must take credit for many a recovery increase. Rigorous metallurgical test work, feasibility analysis, production planning and budgeting should allow for recovery variations due to grade fluctuations. Since the phenomenon is a reflection of ore geology and mineralogy, which are ore specific, comparison of recoveries at different times or sites is not meaningful without a detailed understanding of the mineralogical constraints on gold liberation.

Jan 1, 1997

Iron removal using biologically produced organic acids was investigated as a treatment option for the production of refractory grade bauxite. A leaching solution containing 98mM oxalic and 67mM citric acid was prepared from a sucrose medium using for fermentation the fungus Aspergillus niger. The leaching capacity of the metabolic product was tested on a bauxite sample containing 16-19% iron (as Fe2O3). Aerobic and anaerobic leaching tests were carried out at pH 3, 50°C and in the absence of light. Results indicated that more than 80% of total Fe can be removed from the ore, when the sample is finely ground and applying a two stage treatment. The presence of oxygen was seen to affect adversely the kinetics of the process, suggesting that leaching follows a reductive mechanism. Experiments that were carried out with different particle size fractions indicated that for obtaining efficient removal of iron particles should be finer than 0.63mm. Reduction of the operating temperature from 50 to 30°C caused a decrease in the rate of iron removal by more than 10 times.

Jan 1, 2006

By R. Pakalnis

A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water:cement ratio between 0.35:1 to 0.4:1.

Jan 1, 1994

By J. R. Hindman

The vermiculite review arrived too late for the June issue. In 1992, production of commercial vermiculite in the United States increased 1 % to 170 kt (187,000 st), according to the US Bureau of Mines. The estimated value of vermiculite concentrate was $13.6 million, yielding an average value of $80/t ($72.50/st). Vermiculite is used in several physical forms. Use of the thermally exfoliated product include light weight aggregates, horticultural growth media, thermal insulation applications and absorbents for spill control and liquid waste containment. The untreated commercial concentrates are used as intumescent fillers in plaster board, gaskets and paints. Several chemically modified vermiculite products include clay-sized dispersions and granules for treating flue gas. South Africa was the only major foreign source of vermiculite used in the United States. It exported about 40 kt (44,000 st) to the United States last year. In 1992, Palabora Mining Co. began processing vermiculite in a new beneficiation mill at Phalabowra. It produced about 164 kt (181,000 st). Minor sources of foreign vermiculite concentrates consumed in the United States included about 140 kt (154,000 st) from China. Brazil also exports some concentrate to the United States.

Jan 1, 1993

By James T. Furey, Laurence D. Hartzog, Graham A. Karklin

A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from the gold/tellurides bearing sulphide ore of the Kensington deposit (Echo Bay Mines and Coeur d'Alene Mines), and to compare the performance of column flotation to conventional "mechanically agitated" flotation, Tests were conducted in a 150 mm diameter, 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail. The bulk metallurgical ore sample had an average "as tested" feed grade of about 5 git gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbrayite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of97%, but produced grades of +150 git Au.

Jan 1, 1992

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By John D. Shaw

1. Introduction 2. The Hydraulic Mine _ (i ) Development (i i ) Extraction ( i i i ) Transport 3. The Water Circuit 4. Manpower and Results 5. Modifications 6. Conclusions 1. Introduction The Kaiser Resources Ltd. hydraulic coal mine is located in south eastern British Columbia, Canada, at the western end of the Crowsnest Pass, next to the Town of Sparwood. The seam presently being mined is the number 10, known locally as the Balmer seam, which is a high quality coking coal, 50 feet in thickness and of an average inclination of 35 degrees. The mine was designed in the late sixties as a small scale trial unit, and was to use a single monitor unit, working 3 shifts per day on a 5 day per week basis. Experience has proved the method to be so successful as to warrant the expansion of the ancilliary facilities to cater for the increased production. The annual raw coal production from this single monitor unit has risen from 108,988 short tons in 1970 to 942,334 short tons in 1975, with a total mine labour force of about 160 men including the surface de-watering plant, mine supervision and mine administration.

Jan 1, 1977