Search Documents

By Lawrence Pelham

Introduction Fluorspar demand or consumption has been taken for granted in recent years, except for those that produce, market, or consume the commodity. Thinking used to be that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The US Bureau of Mines (USBM) published an assessment of world fluorspar reserves and resources. It created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The US and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. Goals for the government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. US production and distribution Fluorspar Fluorspar shipments from US mines reached an all-time high near the end of World War II in 1944 at 375 kt (413,800 st). Eighty-two mines produced more than 453 t (500 st) each, and 10 mines produced more than 9 kt (10,000 st.) each. Illinois supplied 43% of total shipments. Consumption in 1944 was 372 kt (410,200 st), of which 56% was used by steel producers and 32% by HF producers. This was the last year that US production exceeded US consumption. The post-World War II record for fluorspar shipments occurred in 1951 at 315 kt (347,000 st) 58 mines produced more than 453 t (500 st) and eight mines produced more than 9 kt (10,000 st).

Jan 11, 1986

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By T. Martinez Patino

Precious metals have been sought by man through time. The search has been the cause of many historic events as well as the founding of the famous Mexican, Minion centers of Durango, Guanajuato, Zacatecas and others. Bacis, a silver - cold deposit in the State of Durango was one of the lesser known centers established during Spanish colonial times. During the past year, metal prices have suffered a substantial decline, resulting in the closure of many mines. Through astute exploration, development and exploitation of the mine, the effect of the low prices has been offset and the mine is surviving these hard times.

Jan 1, 1994

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By L. M. Dyer

Various attempts have been made to build leadership and management expertise with little success. There are numerous reasons these attempts have failed. Three reasons, along with suggested solutions, will be explored: 1) lack of ownership of the development process by those affected; 2) lack of congruence of the development process used and the business strategies of the organization; and 3) a comprehensive development process. We will discuss a development model applied inside a smelter and refining complex over one year involving all levels of management. The process was credited with helping to substantially reduce cost and enable breakthroughs in production, quality and safety results.

Jan 1, 2000

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By V. F. Swanson

A petrographic study was made of the type and sources of mineral contamination occurring on phosphate rock products from Florida. Emphasis was placed on contaminants in the screened rock (+1 mm) since this portion of the product undergoes no physical beneficiation except for scrubbing to remove slimes. Since iron and aluminum con- tent of the finished product affect the salability, special emphasis was placed on identifying types and sources of these contaminants and relating chemical composition to visual characteristics. Wavellite derived from the overburden was the major aluminum contaminant with some aluminum being included as secondary clayballs. Iron occurred as phosphates in the overburden, and as colloidal oxides included in the phosphate pebbles. Chert and limestone contamination were derived from the Hawthorne formation underlying the phosphate matrix.

Jan 1, 1969