Search Documents

By K. A. Natarajan

The utility of yeast, Saccharomyces cerevisiae, in the separation of quartz from hematite is demonstrated. Yeast cells, as well as their metabolites, functioned as flotation collectors, depressants or flocculants and dispersants for hematite and quartz. Interaction between yeast and the above minerals resulted in significant surface chemical changes, rendering quartz surfaces hydrophobic and hematite hydrophilic. Mineral-specific extracellular proteins and exopolysaccharides were secreted by yeast cells when grown in the presence of quartz and hematite, respectively. Quartz could be efficiently separated from hematite through microbially induced flotation and selective flocculation.

May 1, 2012

Passive seismic monitoring is a useful tool for measuring wave propagation in rock mass in deep underground mining. About 20000 mining ? induced seismic events of a hard rock mine, are identified and investigated. The travel times of source-receiver pairs allow us to demonstrate temporal change in velocity. It was found that the average P wave velocity is about 6000 m/s in the mining regions. Velocity investigations on the data during about three months around the main shocks show a significant decrease of the average seismic wave velocity after the main shocks. The sudden drop of average velocity change after the main shocks implies the creation of new fractures in the rock mass due to the main shocks. Afterward, the average velocity increased to a normal level after a time duration of several days. A reasonable explanation for the post seismic velocity increase is that opened cracks begin to close due to crack healing.

Feb 23, 2014

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Henrique D. G Turrer, Desmond Edifor, Marcello R. Cruz, Josue M. de S Junior, Darius Wonyen

A geometallurgical testing program was developed to anticipate ore behavior in the beneficiation plant and support production planning. Over 100 drill core samples from a major iron ore deposit were tested using bench-scale gravity and magnetic separation methods to assess variability in process responses. Results showed significant differences in key attributes such as iron grade, gangue content, slimes generation, and specific gravity, directly impacting concentrate grade, recoveries, and tailings quality. Correlation analysis and regression models were used to link feed properties to process outcomes, and a mass recovery estimation equation (Wrec) was developed for predictive use. The study proposes the integration of geometallurgical parameters—such as Fe, SiO2, Al2O3, LOI, ore type, size fractions, and slimes content—into the block model to support blending decisions and minimize operational risks. This work establishes a solid foundation for long-term mine-to-plant integration, with future phases aiming to expand testing and build a calibrated geometallurgical model.

Feb 22, 2026

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Daniel Willis, Ryan O’Connell

An 8-foot tall horseshoe adit tunnel located within an abutment of the Mount Morris Dam in Mount Morris, NY required repair of a failed reinforced concrete liner. The adit tunnel is entirely founded within highly weathered shale bedrock units, which induced unloading stress on the original tunnel liner. An epoxy-impregnated carbon fiber fabric wrap manufactured by Sika was chosen to repair the failed adit tunnel liner. Kilduff Underground Engineering completed the design of the tunnel repair utilizing both empirical and numerical methods. Merco Engineering Contractors completed the injection of chemical grout and repair liner installation.

Jun 23, 2024

By David A. Rice, Scott A. Shuey, William K. Tolley

The U.S. Bureau of Mines (USBM) is developing new dewatering technology to permit the recycling of iron values contained in wet steel plant sludges. In laboratory tests, Q-BOP fume sludge was dewatered to 12% moisture by displacing water with acetone in a plate-and-frame pressure filter. Acetone is reclaimed through distillation at lower cost than conventional thermal drying of the sludge. The projected additional energy requirement for acetone treatment of the sludge, including acetone recovery, is $5 to $7 per dry ton.

Jan 1, 1995

By W. S. Fyfe, R. J. Puddephatt, S. Zhou

Gold is easily mobilized at temperatures within range 600-11OO°C by gases such as Cl2, CO, H2S, in gas mixtures, at low pressures. Such gases are relevant to conditions of granulite facies metaomorphism in environments of magma underplating. These observations suggest an efficient mechanism for moving gold to the upper crust during major thermal events. The efficiency of precipitation of gold at lower temperatures is related to available mineral surfaces and pyrite appears to be an excellent substrate for gold precipitation.

Jan 1, 1989

By Ron Derrick

SX operators have conducted extensive shut-downs and repairs over the years to mitigate solution leaks from failed stainless steel false floors and walls in rectangular mixersettler mix boxes. Hydrodynamic modeling using first principles and constitutive equations of fluid mechanics can inform an efficient structural redesign sufficient to eliminate the plate failures. Updated mix boxes have been performing without failure for over a decade. Given the extensive construction of the original Holmes and Narver mixer-settler design throughout the world that includes stainless steel lined rectangular primary and auxiliary mix boxes, SX operators may benefit from the approach, eliminating costly shutdowns, leaks to containment, and hazardous repairs.

Feb 1, 2024

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By D. T. Iseley, David Bennett, Christopher Norris

The microtunneling test program is one of three main elements of the research project, "Trenchless Construction: Evaluation of Methods and Materials to Install and Rehabilitate Underground Utilities." The other elements of this project include an evaluation and demonstration of horizontal directional drilling technology and pipeline rehabilitation systems. The research is a Corps and Industry cost-shared project funded under the Construction Productivity Advancement Research (CPAR) program. The laboratory partner is the U.S. Army Engineer Waterways Experiment Station (WES), Geotechnical Laboratory. The industry partner is the Louisiana Tech University's Trenchless Technology Center. Industry participants are contributing over half the total cost of this research. The overall objective of the CPAR program is to improve productivity in the U.S. construction industry, thereby enhancing the competitiveness of the U.S. industry in domestic and overseas markets. The Corps and other federal and state agencies will benefit by realizing reduced costs, enhanced safety and better products and services as the products of this research program are developed, tested, and pushed into the market place. The microtunneling demonstrations and evaluations were performed during September and October 1992 at a specially constructed test facility built at WES in Vicksburg, MS. The test facility is 104 m (340-ft) long, 5 m (16-ft) wide, and 4 m (13-ft) deep. It was constructed, ironically, by first excavating a trench into which 6 different types of soils were placed and compacted in approximately 18.3 m (60-ft) long sections. The soil profiles include a lean silty clay (loess), a dry sand, highly plastic buckshot clay, wet sand, clay gravel and silt. The interfaces between soil profiles were sloped to simulate mixed face conditions as the machines exit one zone and enter another, and provided challenges to ground control and alignment and grade control during these transitions. Moisture and density tests were performed on all materials in each lift to assure uniformity. Horizontal inclinometers and 3 levels of settlement plates were installed at key locations in the test bed. The settlement plates and rods and the horizontal inclinometers, together with surface survey points, provided data to evaluate settlement and heave along the test section. Penetration resistance was measured in each section of the completed test bed. Strain gages were installed in 8 of the 0.6 m (24 in.) diam. Hobas pipe sections to measure strains in the pipe as it was being jacked into place. Steering jack loads, jacking thrust loads, and cutterhead torque were also measured during the drives. The results of these tests will be used together with other information to develop guidelines for conducting feasibility studies and selecting proper methods compatible with anticipated conditions.

Jan 1, 1993

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By C. L. Elmore

This paper describes a new development in the cyanidation of gold ores, which we expect will result in a major improvement in the way many gold ores are treated. The process has evolved through work at Hazen Research, Inc. for Kamyr, Inc. and in brief, the consists of utilizing oxygen rather than air in the carbon-in-1 each (CIL) process. We refer to this improved process for all ores amenable to cyanide leaching as carbon-in-1each with oxygen or CILO.

Jan 1, 1988

By Gail B. Knight

INTRODUCTION In May 1984, The Canadian Pacific Railway awarded to the Joint Venture of Foundation of Canada, Ltd. of Toronto, Atlas Construction Co. of Montreal, and S. A. Healy Co. of Chicago the contract for the construction of 27,000 ft of tunnel starting from the east portal. Selkirk contractors, the Joint Venture of Foundation, Atlas and Healy, which had successfully completed for CPR in 1983 the construction of both portal structures for this tunnel, studied several different alternative proposals before presenting its bid pooling each individual company's technical resources and experiences. (Foundation had just completed in association with other companies a similar tunnel project in British Columbia, and the S. A. Healy Co. could provide its experience of more than 40 miles of tunnels excavated by full face boring machines.) Among the alternatives investigated there was a fully circular tunnel to be excavated by a 30 ft diameter TBM, a full section drill and shoot proposal, and a mixed alternative, the "key hole" proposal, consisting of a TBM driven circular top heading followed by benching to design size. Technical, geological and economical considerations determined the alternative that was eventually proposed to CPR. HISTORICAL NOTES The tunnel construction parallels an existing tunnel through the Selkirk mountains that was excavated in 1885. In order to reduce the grade to 1% on the heavily loaded west bound trains, the new tunnel was at a lower elevation and lengthened to almost 9 miles. GEOTECHNICAL INFORMATION CP Rail site investigations began in 1978. The surface rocks in the tunnel construction area are metamorphosed Cambrian and Pre-Cambrian sediments; the underlying formation contains fine and coarse grained rocks presenting different degrees of metamorphism. The

Jan 1, 1987

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the' same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

By R. L. Grayson, T. L. Dickinson, C. G. Anderson

Sponsored by the EPA, USGS, DOE, and NSF through the Committee on Earth Resources, the National Research Council’s Committee on Material Flows Accounting of Natural Resources, Products, and Residuals, created in August 2002, studied the value that material flows accounting, which can track the flow of a material from the time it is extracted to its ultimate disposal, may provide for making better integrated economic, social, and environmental policy decisions. This could be a crucial technology for the mining industry to incorporate. This paper will recount the statement of tasks, the study process, and the science-based conclusions and recommendations reached.

Jan 1, 2004

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981

By R. Hiebert, M. Foote, S. Nordwick, M. Canty

An innovative biological treatment system designed to detoxify cyanide and nitrate and immobilize metals from cyanide leach operations is described. A pilot-plant demonstration was conducted to detoxify cyanide and immobilize several metals from a process stream at the McCoy/Cove Mine. Testing was performed under the EPA’s Mine Waste Technology and Superfund Innovative Technology Evaluation Demonstration Programs. This technology was successful in detoxifying cyanide and effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed. Results show that biological treatment can offer an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1999

By K. J. Ma, L. Ma, J. Stankus

The paper’s intent is to evaluate pumpable foamed cementitious mine seal material by determining the shear strength of a generic foamed cement in the laboratory. The tests were conducted on three scales: small-size specimens, consisting of cylinders 4 in. in diameter or 3-in. prisms; double shear medium- size specimens, measuring 13 in. by 10 in.; and large-size specimens, measuring 6 ft by 4 ft by 4 ft. The small-specimen shear tests resulted in average peak and residual shear strengths of 128 psi and 56 psi, respectively. These values are fairly consistent with published shear strengths of foamed cementitious material. However, the other two types of shear tests did not achieve the shear strength of a typical pumpable foamed cementitous mine seal material. Based on the test results, the paper concluded that the structural analysis of cement foam seals should be based on their residual shear strengths, approximately 20 psi, determined from small laboratory-scale tests of the cement foam/concrete or rock interface, and not be based on their peak strengths.

Jan 1, 2015

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013