Search Documents

By Ross W. Smith, Salim Akhtar

Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collect- ors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By C. A. Pickles, S. J. Splinter

Silicon oxynitride, Si2N20, has many of the intrinsic properties of a potential high temperature engineering ceramic material. Some of these properties are similar to those of silicon nitride, which has been more intensively studied. However, although silicon nitride ceramics are approaching a state of microstructural refinement for various engineering applications, silicon oxynitride has received little attention. This has been mainly due to a lack of an economical and reproducible method of producing pure crystalline Si2N2O. Several reports exist on the preparation of crystalline Si2N2O from SiO2 and Si3N4, yet very little kinetic data exist. Even less is known about the carbothermic reduction of SiO2 in a nitrogen atmosphere to produce Si2N2O. In this paper, a review of the properties and methods of preparing silicon oxynitride will be presented. In addition, results obtained by reactively sintering SiO2 and Si3N4 will be discussed. The overall reaction is as follows:

Jan 1, 1990

By Douglas W. Fuerstenau

Technological innovation is needed to meet the challenges that face the mineral industry because ores steadily become lower in grade, more complex in mineralogy, and must be processed in the face of ever- increasing environmental constraints and increased costs. How periodic innovation in mineral processing helped overcome the challenges that faced the mineral industry is briefly traced from antiquity up to the present time.

Jan 1, 1989

By L. Lacerda

Shotcrete is widely accepted as an indispensable form of ground control around the world. Other Surface Support Liners such as mesh have been around as long as shotcrete while other Thin Support Liners (TSLs) have been introduced in recent decades. TSLs, however, have yet to replace shotcrete in many applications believed to be “perfect” for them. On the other hand, some recently introduced technologies may be on the brink of meeting most surface rock support requirements economically and safely. This paper will discuss rockfall statistics, small rockfall prevention and compare different surface support liners such as mesh, shotcrete and TSLs. Additionally, a shaft sinking TSL application example will be presented.

Jan 1, 2004

By Jack K. Lemley

This paper will provide an update of the Channel Tunnel Project including a discussion of the overall legal structure and management organisation. It is important to understand the mission that TML, as a design/build contractor, has undertaken and how the various interfaces have evolved between the other entities involved in the project. The paper will describe the evolution of the management organisation and the approach to completion of our contract, recapping the historic events and moving into a projection of how we will manage the completion of this very large transportation system.

Jan 1, 1991

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By William C. Cox, Ronald E. Heuer, Jean-Michel Loignon

The Gatineau shaft described in this paper was an excavation of about 38 m diameter and 21 m depth constructed in Gatineau, Quebec, across the Ottawa River just north of Ottawa, Ontario. A large sewage lift pumping station-was to be constructed in this excavation. Subcontractor for the shaft excavation and initial support was Beaver Underground Structures Ltd., of Dorval, Quebec. Mr. William C. Cox of Beaver conceived the idea for the support system used in this excavation, and was responsible for the construction activities. Initial analysis and design concepts for the lining system were developed by Mr. Ronald E. Heuer. Detailed lining design and construction monitoring were the responsibility of Mr. Jean-Michel Loignon. Geologic conditions indicated by two borings within the shaft area are illustrated in Fig. 1. The shaft excavation would be in the sensitive Leda silty clay. The clay is of stiff to very stiff consistency, with an insitu vane shear strength averaging about 115 KPa (2400 psf) and a reported low value of about 87 KPa (1820 psf). Low strength values were from the middle of the clay layer, with higher strengths at the top and bottom. Average shear strength at the level of the base of the excavation was about 137 KPa (2860 psf). Remolded vane shear strength averaged about 20 KPa (420 psf), with a reported low of 13 KPa (270 psf). Based upon average strength values, the clay sensitivity is 5.8. The clay has an average water content of 53% (range 43 to 66%), which is near its liquid limit (average 56%). The clay unit weight is about 1760 kg/m3 (110 pcf). Underlying the shaft site at shallow depth is limestone bedrock within which the piezometric head is approximately equal to the original ground surface elevation. For shaft support, a -cast-in-place concrete wafer system was considered, but was discarded because of time restrictions imposed by concrete placement and curing. The support system selected utilized liner plate with light steel walers closely spaced. The light rib

Jan 1, 1983

By Vas Choudhry

INTRODUCTION Traditionally mineral processing equipment has been procured based on (equipment) specifications prepared by the engineers. As newer materials of construction are being used for equipment manufacture and plant control systems become more sophisticated, the need for thorough and detailed specifications is greater than ever. For example, it is not uncommon to find plants looking at grinding circuits consisting of semiautogenous mills with variable speed, gearless, drives of large horsepower. Technical specifications for the mill, wrap- around motor and control system must, therefore, be carefully prepared to ensure that the respective equipment supplied by vendors meets overall grinding needs. Various engineering and design companies have expended considerable time and effort in developing the specification format. Equipment manufacturers have also given significant effort to developing data sheets aimed at collecting information regarding not only the duty of the equipment, but also the conditions under which it will be operated. As engineers moved from one company to another, the specification format became cross-fertilized and further developed. As a result, specifications on file with various engineers have improved considerably over a period of time. Equipment specifications from earlier projects are commonly used as a basis for tailoring new ones. To keep equipment specifications short, general technical considerations are often compiled as separate specifications. For example, general considerations applicable to the design, manufacture and supply of the mechanical equipment are consolidated under "Standard Requirements for Mechanical Equipment” and included along with that specified for purchase. As the economic feasibility of the project has been established during earlier studies, purchase-related activities can be initiated following completion of the specifications. Procurement itself is a major activity, however, in this chapter only those activities directly related to the purchase of equipment will be discussed. PREPARING EQUIPMENT SPECIFICTION Specification for process equipment or machinery is written in such a way as to define exactly what is required of the equipment. Generally, mechanical

Jan 1, 1986

By Sheldon Shepherd

Fifty years ago, belt scales were mechanical devices based on a complex weight balancing design. Today's systems use load cells to assess material weight, belt speed sensors and microprocessor-based integrators to continuously compute the rate of material transferred along a conveyor. Belt scales have become important assets to a plant. They help maximize the use of raw materials, control inventories and aid in the manufacture of a consistent product. Choosing and installing a belt scale system may seem complicated but it can be simplified by following a few guidelines.

Jan 1, 1999

By Timothy J. L. Haley

The population of the Rhondda underwent a spectacular rise as energy requirements increased in the mid-nineteenth century. The rapid expansion in the demand for coal transformed the population from a few hundred sheep farmers in the eighteenth century, into a thriving coal-based economy of some 168,000 inhabitants in 1924. Cochrane (1958) put forward the idea that the differential migration of more healthy men from the Rhondda Fach during the period since the peak of population in 1924, had resulted in a respiratorily-impaired residual population. This idea was used to explain the reduced survival of miners & ex-miners aged 55-64 years from this valley as compared with a similar group from Leigh in England. Using the proportional hazards regression model of Cox (1972), a comparison is presented of the exact twenty-year mortality of migrant and non-migrant miners & ex-miners and non-miners from the Rhondda Fach. The analysis makes allowance for the pattern of migration throughout the twenty-year period and adjusts for the confounding influence of variables such as age, occupation, and category of Simple Pneumoconiosis. The results indicate that contrary to expectation, any effect of migration upon mortality is manifest only at higher ages. Furthermore, for these men, the migrants have worse survival than the non-migrants. Also, contrary to expectation in the light of work by the British Coal Board (Soutar et al, 1982) there is no evidence of increased mortality amongst men with category I simple pneumoconiosis. INTRODUCTION [The Background] In September 1950, the Medical Research Council's Pneumoconiosis Research Unit at Penarth in South Wales initiated a study of lung disease in the smaller of the two Rhondda Valleys - the Rhondda Fach. At that time, the primary interest was in assessing the possible role of pulmonary tuberculosis in the aetiology of the serious (complicated) form of coal-workers' pneumoconiosis, i.e. Progressive Massive Fibrosis. The Rhondda Fach is situated in South Wales, some 25 km north-west of Cardiff. It is a narrow winding river valley about 12 km long, and approximately 1 km wide. The name means Little Rhondda; there is a corresponding Big Rhondda - the Rhondda Fawr. Together, these valleys make-up most of the Rhondda Municipal Borough. Following the initial survey in 1950-51, there have been several follow-up studies of this population. In addition, amongst numerous other investigations to unravel the aetiology of coal-workers' pneumoconiosis, Medical Research Council teams studied various other (sample) population groups, particularly in the industrial areas of the adjacent Aberdare Valley, and in Staveley and Leigh in England. The agricultural areas of the Vale of Glamorgan in South Wales, and Annandale in Scotland were also studied.

Jan 1, 1993

By J. T. Gepford, K. A. Prisbrey, T. Scott, M. Spangler

Using neural networks for plant control is challenging. The objective was to show how to make a neural network effective, even with noise, lag times, and unmeasured disturbances in the plant. The procedure was to evaluate the neural network in a laboratory flotation vision system and in a plant refractory gold autoclave system. Although the resulting neural network easily conquered simple laboratory data, the noisy plant data was much more difficult, and adaptive linear models were equally effective. We concluded that the neural network needs support by combining it with other tools found in the best control packages.

Jan 1, 2000

The authors give a corrected form of the Korobov algorithm of optimal open pit determination and describe a method of optimising the mining sequence within a preliminary pit design. A method of automatically including roadways is also given.

Jan 1, 1992

By M. Cambridge

The design process must anticipate all construction and operational conditions and make an allowance for all eventualities. Prevention of failure during operational life, and in some cases post abandonment, requires that a risk assessment is undertaken during the design stage which defines not only the factors of safety to be used but the criteria for the structure during its operating life. These operating criteria should clearly identify the at-risk structures and the inspection and monitoring routines required to ensure compliance with the design objectives. On a mine site, it is the role of mine management to ensure that the operating rules be applied throughout the mine life and that a system of inspection and monitoring procedures be instigated. Where the risks are significant, high-level auditing by an independent engineer will also be required. Within the inspection and auditing framework, the designer needs to incorporate instrumentation to enable the operators and management to confirm that the facility meets the requirements of safety, stability and environmental compliance whilst continuing to meet its operational function. This paper reviews the use of inspection and monitoring to prevent failure and provides, in summary, examples of where monitoring has been undertaken and prevented failure. A tabulated review of legislation, regulations and technical guidance generated as a result of previous failures or untoward events is provided.

Jan 1, 2005

By George H. Klein, B. Kent Merritt, Anthony Crisci

During the past decade, over 114-km (71-mi) of 0.25-m (10-in) to 3.7-m (144-in) finished diameter tunnels have been driven below Metropolitan Houston as part of a major program of water and wastewater improvements. This large effort has seen the introduction of midwestern technology with over 18-km (11-mi) of man-entry pipe jacking and European and Japanese technology with over 21-km (13-mi) of microtunneling. Owing to the high water table; a stratigraphy consisting of stiff fissured clays containing numerous layers, channels, and lenses of water-charged sands and silts; and active faults, many challenges existed for designers and contractors alike.

Jan 1, 1991

By Firoze E. Katrak, John R. H. Black, Paul R. Ammann, Michael J. Loreth, Servi. Italo S.

Germanium is produced primarily as a by product from zinc concentrates. The important sources of gallium are alumina ores (bauxites) and zinc concentrates and residues from zinc processing. In addition, gallium as well as germanium may soon be recovered from a depleted copper mine near St. George, Utah. The major uses for germanium are in semiconductors, lenses in infrared optical systems, catalysts, and gamma radiation detectors. The major markets for gallium are in light-emitting diodes, solar cells, laser diodes, integrated circuits, microwave devices, and magnetic bubble memories. CRA projects a healthy growth in the demand for both metals. However, the role of scrap metal will continue to be important over the next decade, thus decreasing the overall demand for primary gallium and primary germanium. This paper summarizes the key elements and the economics of the markets for germanium and gallium. Much of the information, such as plant-by-plant costs of production and estimates of consumption by end use for various countries is from proprietary databases of Charles River Associates.

Jan 1, 1986

The tungsten carbide insert bit has probably advanced blasthole drilling more than any other single improvement. Tungsten carbide inserts have longer life, maintain sharper edges, and penetrate faster than hardened steel edge bits. Before the tungsten carbide hit appeared, all-steel bits were used. Even with the new bits, blasthole drilling costs vary with the type of equipment used and its condition; the hole's length and diameter; the rock's texture, hardness, and nature; the operator efficiency. To help reduce drilling costs, the operator should be familiar with the use and care of drill bits. This article provides information about tungsten carbide rock bits used for percussion drilling. Consideration of tungsten carbide rock bits includes looking at bit materials [ ] as well as bit operation and maintenance. Two basic tungsten carbide rock hits are the button bit and the four-wing carbide insert bit. Three common hit-to-drill-steel connections are the bottom drive, tapered drive, and shoulder drive. Bottom drive bits arc typically used for singlepass or longhole drilling, with all percussion drills from handheld sinkers to heavy track drills. Tapered socket bits are available with shallow or deep carhide inserts, for the lowest cost depending on the rock type being drilled. Shoulder drive bits are available in all-steel or carbide insert design.

Jan 12, 1981

By Keith Kern, Joseph P. Matoney, Kenneth E. Harrison

INTRODUCTION "When there is an economic need for cleaning fine coal to low ash, the technical difficulties will be solved. The utilization of fines below 28 mesh will determine the degree to which beneficiation will be carried. Whenever these "fines" will be processed into smokeless fuels or used as new materials for the chemical industry or for hydrogenation, a higher degree of cleaning will be economically justified”.(l) This quote from the 1943 edition of Coal Preparation correctly anticipates the use of fines as "smokeless" fuel or as a future component of boiler fuel and a1 so as a raw material for the chemical industry or possible new uses such as for internal combustion engines. Fines utilization depends upon an economic need and possibly neglects to say an environmental need or a government funded development program as the prime mover for development. In any event, this conference is faced with the "need" to beneficiate fine coal and undoubtedly among the processes that will be discussed are the unit processes of future coal preparation facilities. HISTORY OF DEVELOPMENT It is interesting to look at where we have been, where we are now and where we possibly will be in the future. In order to put some limitations on this presentation, we will for the most part confine our remarks to this century and particularly developments since World War II. We also will limit our remarks to the preparation of bituminous coals in the United States, and for the most part, to wet processes. In the 1943 edition of Coal Preparation, clues to the processes being used to beneficiate coal are contained in the Chapter Titles. An extensive treatment of "Hand Picking" was contained in Chapter 8. Chapter 7 contained a description of methods for "Preparation at the Face". Chapter 18 dealt with "Slurries, Sludges, Slimes and Water Treatment" and defined this size of coal as being the size at which "Jigs and Chance Cones are usually dispensed with and other methods such as the hydrator, tables, and froth flotation are employed. Generally the limit is 1.7mm to 3.4mm. In the days before World War I1 the then modern bituminous coal preparation plant contained jigs or Chance Cones for the coarse material +6.35mm, concentrating tables, launders or some classifier type of coal washer for the fines (6.35 x 0.15mm), and froth flotation as the only method of cleaning minus 0.15mm coal which was used very sparingly.

Jan 1, 1988

By Edward H. Opitz

Much has been written recently about the Henderson Mine Project in Colorado being developed by American Metal Climax, Inc. To briefly recap the project, AMAX has an ore body, containing about 300 million tons of proven and probable molybdenum ore which is located under Red Mountain on the eastern slope of the Continental Divide. The mill, however, will be located on the western slope in the Williams Fork Valley where water and space for waste disposal are more available. AMAX will carry the ore by remote controlled trains from a gathering level underground at the mine, through a ten (10) mile tunnel under the Continental Divide and thence along a five (5) mile surface railroad to the mill site. One of the more challenging facets of the project is the western portion of the ten (10) mile tunnel being driven by Dravo Corporation through difficult ground conditions, downgrade, toward the Continental Divide. The tunnel is a 16'-6" wide by 15' high horseshoe, which runs in a straight line and drops at a constant three percent (3%) grade from the West Portal to the ore zone. Dravo's portion is anticipated to be about 6 1/2 miles long and includes permanent pumping stations located every 4,900 linear feet (lf) permanent rectifier stations every 12,5001f, and one (1) 1,560 ventilation shaft. The western portion of the tunnel lies in the Idaho Springs formation, a mixture of gneiss and schist with some granitic intrusions. Toward the Continental Divide a transition into Silver Plume Granite is expected to occur. Preconstruction geologic information indicated the Idaho Springs and Silver Plume formations to be basically competent with some faulted and altered areas. It

Jan 1, 1974

By Lane White

Loading shovels are at the heart of most surface mine production. As truck sizes have increased, shovel manufacturers have matched them with larger shovels (see table, page 343). Further increases in shovel size may be in order if trucks in the 270-t (300-st) range find acceptance at the largest surface mines. However, larger shovels are not currently the primary focus of shovel design engineers. Competition and user pressure are combining to keep their work directed toward improved shovel productivity and efficiency. Computer design technology and advanced electronics play an increasingly prominent role in this work. "Improved diagnostic capability, system monitoring, vibration analysis and above all increased user friendliness in machine control systems are being pursued by most manufacturers working in our industry today," observes Stuart R. Cotterill, director of marketing for Harnischfeger Corp. The use of computer-aided design (CAD) systems in shovel design has been in place for many years. However, recent advances in computer capability and improved software programs and graphics are making computers even more useful.

Jan 1, 1995

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991