Search Documents

By Chen Wen, Li Zhao-jia, Zhao Qiang, Ning Shun-ming, Tang Sanchuan, Wang Hong-qiang

"The carbon-burdened and cold-bonded pelletizing-electrosmelting process is used to dispose low-grade manganese, and the qualified rich-manganese slag is obtained. On the condition that reduction roasting temperature was 1000?, reduction time was 45min, particle-size was -1mm, reductant dosage was 1.6%, basicity was 0.3, smelting temperature was 1410?, smelting time was 60min, it had a good effect on the melting between slag and metallographic phase, the manganese content was 32.58%, manganese recovery was 92.16% in the slag; while the iron content was 94.40%, iron recovery was 95.32% in the metallographic phase. It was proved by the demonstration tests.IntroductionManganese is an important raw material for steelmaking, which is extensively utilized in modern industry, the consumption of manganese for iron and steel industry accounts for 90% to 95%. After mining over 30 years, the high-grade manganese resources drop markedly, especially with the hypergrowth of steel industry, the domestic manganese is far from the requirement, as a result, we have to buy significant quantities of manganese overseas. Besides, the property of imported manganese is more and more complex, and the high-grade and lump manganese decrease year by year, while the fines and high-crystal water manganese are on the increase. Therefore, how to make effective use of domestic low-grade manganese and intensify the manganese’s smelting is an effective approach to reduce the cost of manganese series ferroalloy and improves market competitiveness[1-4]. It has important practical meaning."

Jan 1, 2012

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Jonkion M. Font, Ramana G. Reddy

A thermodynamic model for a priori predictions of arsenic and antimony impurity capacity in Ni-Cu mattes and slags was developed based on the Reddy-Blander (RB) capacity model. The As and Sb capacities were calculated a-priori considering the RB capacity model in Ni-Cu mattes and FeO-FeO1.5-MgO-CuO0.5-NiO-SiO2 slag at 1573 K and 0.1 to 1 atm partial pressure of SO2. The results showed an excellent agreement between the model calculated and experimental data of arsenic and antimony capacities between the mattes and slag. The impurity capacity model developed here, can be extended for prediction of impurity capacities in multi-component base metal slags and base metal mattes. Such a priori predictions of impurity capacities can lead to develop or improve the efficiency of impurity removal from the base metal smelting, converting and refining processes.

Jan 1, 2014

By Adam Powell, David Dussault

"Electric Field-Enhanced Smelting and Refining is a process for driving the reaction between carbon in hot metal and iron oxide in slag, for example, in a steelmaking reactor. This process involves inserting electrodes into the slag and metal phases, such that the overall reaction FeO + C -> Fe + CO is separated into two half-cell reactions: Fe2+ + 2e· -> Fe at the cathode in the slag, and C + O 2 • -> CO + 2e· at the anodic slag-metal interface. Without the electrodes, the reaction is very slow, but with electrodes, the additional surface area available to the ferrous ions for reduction accelerates the reaction even without any applied bias. When a bias is applied to the electrodes, the electric field across the slag further accelerates the overall reaction.With or without applied bias, the process is first-order in the ferrous ion concentration, and limited by ferrous ion transport to the cathode. To complicate matters, as the liquid iron is reduced at the cathode, the Mullins-Sekerka instability leads to formation of dendrite-like liquid iron fingers which grow into the slag. Because of this, the design of the cathode can have a significant effect on the overall process kinetics, and understanding of the dynamics of these fingers and of their effect on mass transfer is necessary for the intelligent design of the overall process and the cathode in particular.Toward this end, a detailed mesoscopic two-phase slag-metal model is presented here which describes multi component diffusion in the slag and fluid flow in both phases in the vicinity of the cathode. Diffusion in the slag is driven by chemical and electrical potentials. The phase boundary is modeled as a diffuse interface using a phase field approach. Because this electrochemical reaction occurs at high-temperature, the kinetics of charge transfer and adsorption through the double layer are fast relative to transport, permitting the use of simple linear reaction kinetics. This also eliminates the need to discretize the double layer, with the result that charge neutrality may be assumed everywhere in the domain. Introducing electric field dependence of the gradient potential and well height coefficients in the free energy function allows the model to capture electrocapillarity at the interface."

Jan 1, 2001

By Fuqiang Zheng, Shuai Wang, Ting Duan, Yufeng Guo, Tao Jiang, Andrew Yakovlevich Travyanov

Organic compound binder can effectively enhance the strength of green pellet and reduce the addition amount of binder during pelletizing. However, compared with traditional bentonite binder pellet, the compressive strength of the preheated and roasted pellets significantly declined. It is of significance to resolve this problem for the application of organic compound binder. In this paper, magnetite concentrate was used as raw material, carboxymethyl cellulose (CMC)- bentonite compound was used as binder, characteristics of preheated and roasted pellets and the effects of additives on that were systematically studied, The results show that sodium acetate can effectively improve the characteristics of the finished compound binder pellets. The compressive strength of the preheated and roasted pellets were increased by 52/N·p-1 and 342/N·p-1 respectively when the addition amount of sodium acetate is 2.2%wt of compound binder. Moreover, sodium acetate has no adverse effect on pelletizing process and drying characteristics of green balls.

Jan 1, 2015

By Holger Cordes

X-ray diffraction has long been used for qualitative and quantitative mineral analysis but Rietveld data analysis is still an under utilized method for mineral exploration and processing applications. In this full-profile approach the structural parameters of each mineral phase, together with experimental parameters, are refined by least-squares methods to minimize the difference between observed and calculated diffraction patterns. The result is a standard-less, quantitative analysis of the mineral abundance in the sample that is more accurate and considerably faster compared to traditional methods. The TOPAS software package combines a user-friendly interface with a unique approach to resolve overlapping peaks. Automated analysis options are also available and significantly reduce analysis time for routine samples. Several examples on a wide range of naturally occurring rock types are shown that illustrate the capabilities and limitations of the method. The examples include several options for the quantification of amorphous constituents like volcanic glasses.

Jan 1, 2006

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinler should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified, In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Taiping Lou

The effects of slag composition, additive agents, and heat treatment conditions on the perovskite (CaO ? TiO2) crystal morphology, the precipitation behavior, the crystal growth and the volume fraction (VF) in the Ti-bearing blast furnace slags were investigated. The morphology of perovskite is dispersed dendriform in molten slags. The crystal growth mechanism of the remelting of fine dendrites and the coarsening of larger grains exists throughout the solidification of molten slags. With the temperature decrease, the VF was increased and Perovskite transformed from fine dendrites to coarsening ones or equiaxed grains. The lower cooling rate can increase the VF and coarsen the grain obviously, while higher cooling rate will decrease the VF and reduce the average equivalent diameter (AED) of Perovskite. When .increasing the content of CaO and Fe20}, the VF can increase obviosly. However, high basicity will give rise to the increasing of viscosity of slag, which result in the reducing of the AED. The experimental results showed that additive CaF2 and MnO can efficiently decreased the viscosity of the slags, and obviously improved the morphology of perovskite and promote growth.

Jan 1, 2000

By Defeng Zhou, N. Trubaki, Jian Meng, Fanzhi Menga, Xiaojuan Liu, Yanjie Xia

"The microstructure and the electric conductivity of (Ce0.9Nd0.1)1 xMxO2 d (M=Mo, W) solid solutions were investigated. It has been found that their conductivity containing the grain (s gi ), the grain boundary (s gb) and the total conductivity (s t ) at 300°C- 700°C can be ranked as: (Ce 0. 9Nd 0. 1 ) 0.99 W 0.01 02- d (s gi = 0.065 S.cm·1, (s gb = 0.265 S.cm·1, s t = 0.039 S.cm-1) > (Ce0.9Nd0.1)0.99Mo0.01O2- d (s gi = 0.053 S.cm·1, s gb = 0.142 S.cm·1, s t = 0.029 S.cm-1) > Ce0.9Nd0.1 s 2- d (s gi 0.045 S.cm-1, s gb = 0.091 S.cm-1, s t = 0.018 S.cm-1) measured at 700°C. The highest conductivity is obtained in (Ceo.9Ndo.1)0.99W0.01O2 d. These results indicate that (Ceo.9Nd0.1)0.99W0.01O2- d is the most promising electrolyte materials of intermediate-temperature solid oxide fuel cells among (Ce0.9Nd0.1)1-xMxO2- d. IntroductionRare-earth (e.g. La3+, Nd3+, Gd3+ and Sm3l doped ceria-based ceramic materials have been acknowledged to be attractive electrolytes for solid oxide fuel cells operating below 600°C due to their high ionic conductivity [1, 2]. In order to improve ionic conductivity of these electrolytes further, in recent reports [3-6], some aids such as Mo03 [3] etc. in a limited amount can be used which causes extremely high conductivity. For example, Zhou et al. found that with MoO3 doping, the grain boundary conductivity of Nd3+ doped CeO2- d increased notably especially at lower temperatures due to the effect of severely undersized do pants [3]. It is well known that the size of W6+ (rw6+ = 0.60 Å) is close to Mo6+ (rMo6+ = 0.62A) because of lanthanide shrinkage. Thus, rare-earth doped ceria e.g. Nd3+ doped CeO2g with WO3 in a limited amount will be probably good and even better electrolytes. However, much less information is available about these materials. Therefore, in our paper, (Ce0.9Nd0.1)0.99 1-xMxO2- d (M=Mo, W) solid solutions have been prepared and characterized. Much higher conductive electrolytes are found in the series of (Ce0.9Nd0.1)0.99 M0.01O02- d particularly (Ce0.9Nd0.1)0.99W0.01O2- d"

Jan 1, 2012

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinter should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified. In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organization (CSIRO) have, over the past 15 years, jointly developed the Isasmelt process. This process is based on the use of the Sirosmelt top-entry, submerged combustion lance, developed by the CSIRO in 1973. While the Isasmelt technology was first applied to lead smelting, it has more recently been adapted to smelt copper concentrate. A 15 t/h demonstration Copper Isasmelt plant was commissioned in MIM's Mount Isa copper smelter in April 1987. The success of the Copper Isasmelt demonstration plant, which smelted over 532,000 metric tons of copper concentrate, has led to the construction of two full-scale furnaces: a 104 t/h furnace in the Mount Isa copper smelter, and a 585,000 t/y (650,000 short t/y) furnace at the Cyprus Miami Mining Corporation smelter at Miami, Arizona. The commissioning of these furnaces commenced in August and June 1992, respectively. The MIM Copper Isasmelt furnace will raise the Mount Isa copper smelter's capacity to 265,000 t/y of copper. The plant includes several innovative features, including: Andritz pressure filters, a rotary holding furnace, and an Ahlstrom flux-flow boiler.

Jan 1, 1993

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By William Petruk

The mineralogy of the primary and oxidized ores from the Malanjkhand porphyry copper deposit in India was studied to determine ore characteristics that affect metallurgy, and to assess applicable processes for recovering the copper. Three mineral assemblages were found. One occurs in primary ore, another in moderately oxidized ore, and a thir:d in intensely oxidized ore. Chalcopyrite, the main mineral in the primary ore, is relatively coarse-grained, with grain size increasing as the ore grade increases. High chalcopyrite liberations should be achieved at a relatively coarse grind, and good chalcopyrite recoveries should be obtained. The chalcopyrite, however, tarnishes readily and oXidizes to chalcocite in a relatively short time (several months). The presence of both the tarnished chalcopyrite and chalcocite may affect chalcopyrite flotation and reduce copper recoveries, The moderately oxidized ore occurs in an oxidized cap immediately above the primary ore, and stockpiled primary ore alters quickly to a moderately oxidized ore. Chalcocite is a major copper-bearing mineral in moderately OXidized ore. The concentrator processing this ore should be capable of handling a chalcocite-rich ore. The intensely OXidized ore contains a wide variety of acid-soluble copper-bearing minerals. Leaching may be required to recover the copper from them.

Jan 1, 1987

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Wenming Wang

Recycling of retired cadmium telluride (CdTe) photovoltaic (PV) modules has attracted attention due to new European environmental regulations. Recycling tellurium from CdTe PV modules is becoming more important because of the low availability of this metal. We investigated several treatment paths for reclaiming tellurium from solutions obtained from leaching fragments of CdTe PV modules. Our experiments showed that conventional soda ash neutralization/hydrolysis methods recovered only 50~60% of tellurium. However, by appropriately combining neutralization and sulfide precipitation, almost all the tellurium present in the leaching solution was precipitated and recovered; the concentration of tellurium in the processed solution was reduced from 900-1000 mg/L to less than 1 mg/L, yielding a tellurium recovery greater than 99%. This method can be incorporated in the scheme of recycling spent CdTe PV modules and manufacturing wastes. It may be also an alternative to the current operations for removing tellurium from copper anode slime leaching solutions.

Jan 1, 2006

By Graham Cooke, Abhishek Lahiri, Animesh Jha, E. Jeya Kumari

"CO2 reduction by alternative energy devices such as wind-power, electric vehicles utilize rare-earth elements (REE) in several forms; such as in piezo-electric devices, batteries and magnetic materials. In 2010, the 95% of Rare Earth supply is controlled by China, compared to USA being dominant supplier in the 1980s. The dependence upon a single source of lanthanides has prompted the utilization of lower grades of titaniferous mineral concentrates, which often have rich seams of REE. We propose a new methodology, which utilizes the low-grade minerals for the extraction of synthetic rutile and also significant quantities of REE. We demonstrate the alkali roasting of lower grades of mineral concentrates and subsequent leaching in an aqueous medium for preferential flocculation of REE during the extraction of synthetic rutile. Changes in mineral structure during alkali roasting and leaching determine flocculation of REE and permit their separation at the front end of unit process.The physical chemistry and crystal structure of minerals in equilibrium with alkali and aqueous medium play an important role, which we explain by demonstrating the changes in the crystal structure. The quantification of separation of RE oxide via chemical analysis suggests that it may be possible to separate rare-earth oxides between 50 and 80% of the initial concentration in the non-magnetic fractions of ilmenite, for example. The microstructural and X-ray diffraction analysis points out that the presence of alumina and roasting with potassium based alkali enhances the separation and flocculation of rare-earth elements at the front end of the process after roasting. The process allows the recovery of CO2 generated by recycling into the process for the regeneration of alkali."

Jan 1, 2011