Search Documents

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By E. Ilgar

"Deposition studies were conducted in acid copper electrolyte to determine the influence of chloride ions on cathode morphology. A statistically designed screening test was carried out in the absence and presence of 20 ppm CI- using a three factor, two level factorial design, in an electrolyte containing 36 gl'! Cu2+ and 150 gl-! H2S04, The independent variables evaluated were agitation; current density and temperature and their influence on surface roughness was determined. The copper deposited at current densities where activation was the primary control mechanism appeared similar in morphology whether stirring was used or not. The addition of 20 ppm CI- to the electrolyte gave rougher deposits under the same conditions. In the mixed control regions, considerably rougher, dendritic deposits were obtained when CI- was present. Agitation was effective in reducing the copper surface roughness both in the apparent activation and mixed control regions in the presence ofCI-. The results of this study showed that 20 ppm Cl- polarized the copper deposition at low overpotentials but caused depolarization at higher overpotentials.IntroductionChloride ion is inherently present in copper electrolyte, either as an additive or from other sources such as make up water. The behavior of the chloride ion is well documented in electrorefining operations, but its role in copper winning is less obvious. However in both cases there is evidence that cathode growth and solution chemistry are strongly influenced by its presence. The mechanism and electrochemical action of the Cl"" have been shown to be very complex, therefore a better understanding of its influence on electrocrystallization is essential for improved cathode deposit growth control. It was proposed that Cl"" polarizes the copper deposition reaction at low concentrations due to CuCI formation but depolarization occurs at higher concentrations due to the formation of a soluble CuCI2"" complex [1,2]. Franklin [3] reviewed the mechanism of additives in the electrodeposition process and proposed that the Cl"" complexed with copper, adsorbed on the cathode as an induced anion leading to an increase in the reduction rate. At cathodic overpotentials less than 100 mY, lppm NaCl had a polarizing effect, i.e. an increase in impedance of the charge transfer step. At higher Cl"" concentrations up to 100 ppm, depolarization occurred as evidenced by a decrease in impedance, which was attributed to soluble cuprous complexes [4]."

Jan 1, 1997

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace&apos;s hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By M. J. Collins

Direct pressure leaching of zinc sulphide concentrates was started? commercially in October 1980. Continuing research and development studies at Sherritt and feasibility studies for a number of clients have defined various pressure leach configurations for integrattons with existing roast- 1 each operations and for grass roots plants. Existing and potential applications of zinc pressure leaching are discussed.

Jan 1, 1990

By B. R. Westphal

The Integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on the pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting process. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds is produced. Waste characterization of this stream, developed by using present operating data and chemical analysis, was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can successfully recover over 94% of the metal. Recycling the recovered metal to the injection casting process was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed relative to their effects on the viability of recycling the material. A discussion of the criteria that is being used to establish the acceptable operating limits is also presented.

Jan 1, 1992

By Ikuhiro Sumi

A new steelmaking process, in which manganese ore was intentionally reduced, was developed to achieve a higher manganese Yield using a combined blowing converter. In this study, manganese behavior was discussed through the introduction of a model. Apparent reduction rates of manganese were calculated by the two terms that were determined experimentally, with SOkg and 2S0ton combined blowing converters. The model calculated manganese changes during the operation. We applied the model to the actual operation and found that manganese behavior was predicted fairly well by this model.

Jan 1, 1996

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By S. Seetharaman

In the processing of molten metals, it is extremely important to monitor continuously the concentration levels of various minor elements, In the production of common metals like copper, iron and aluminium electrochemical sensors involving solid, as well as liquid electrolytes are being increasingly used to measure the concentrations of minor elements The present paper deals with the electrochemical principles underlying these measurements and the possible errors involved. One of the major difficulties in the case of the solid electrolytes is to correct for the consequences oldie electronic contribution to the conduction of the electrolyte. The application of the electrochemical sensors for molten metals processing involves designing of these probes to withstand the industrial operating conditions. In this respect, significant achievements have been made with respect to the design of oxygen probes for liquid metals in general and liquid copper in particular. Some of the salient design features are discussed in the paper, The application of auxiliary electrodes for impurities in molten metals like phosphorus in copper and silicon in iron are taken up. The development of oxygen sensors for slags is given special attention. Recent developments&apos; in the field of sensor technology, as applied to metals processing are highlighted.

Jan 1, 1996

By Katsutoshi Inoue

Pectic acid gel crosslinked with epichlorohydrin was found to have very high selectivity to lead(II) and iron(III) ions over zinc(II) ion compared with commercial weakly cation exchange resins containing the same carboxylic functional groups, suitable for removing small amount of impurity metal ions from waste zinc plating solutions. In order to lower the cost, new adsorption gel was prepared from orange juice residue containing pectic acid by crosslinking with epichlorohydrin, which was also found to be suitable for removing these impurities. Further, very cheap adsorption gels was prepared not only from orange but also from apple juice residues by a simple method through just saponificating pectin substances contained in these residues into pectic acid by calcium hydroxide followed by water washing and drying. These adsorption gels exhibited excellent adsorption behaviors for removing the impurity metal ions away from zinc.

Jan 1, 2003

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces, The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as S02 in the flash furnace. Preliminary experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

By T. Thuy Minh Nguyen, Sathish K. Lageshetty, Paul Bernazzani

The addition of nanoparticles to epoxy resins often results in changes in the physical properties of the material particularly when dealing with thin coatings. By characterizing the mechanism of interactions between nanoparticles and polymer chains the material could be tailored for specific applications or properties such as enhanced biodegradability. This study compared the characteristics of common DGEBA resin coated on a silicon substrate and embedded with nanoparticles of TiO2 and Fe2O3. Specifically, we investigated the rate of curing, and the thermal stability of these nanocomposites. Results show changes in the stability for compounds containing TiO2, while Fe2O3 significantly enhanced the curing rates of the nanocomposites while maintaining similar physical properties.

Mar 1, 2017

By Corby G. Anderson

Hydrometallurgical technology for the pretreatment of refractory gold concentrates has been developed at Sunshine Mining and Refining Company. It employs a patented nitrous-sulfuric acid pressure leaching process which&apos; was proven industrially at the Sunshine refinery. Additionally, pretreatment for removal of antimony and some other impurities is done with alkaline sulfide leaching. This paper will discuss the successful application of these two technologies for pretreatment of a refractory gold concentrate prior to CIL gold recovery. A complex gold concentrate composed of pyrite, arsenopyrite and stibnite was tested. Results of antimony leaching in alkaline sulfide media will be discussed including some details of a novel and selective recovery method for gold leached by polysulfide or thiosulfate" Also, the factors important in and the results of the application of nitrogen species catalyzed pressure leaching to refractory gold concentrates will be detailed.

Jan 1, 1996

By R. G. Hilton

This paper deals with application of Super Detox? stabilization technology to the treatment of electric arc furnace dust (US-EPA listed hazardous waste KO61 ). The process has been used on approximately 170,000 tons of electric arc furnace dust. In addition to the nearly four years of commercial experience at Sterling, Illinois, the process is now being permitted for application at two other locations. The process was originally developed by the Bethlehem Steel Corporation and then further improved by Conversion Systems, Inc. (Bethlehem Steel&apos;s Licensee). The treatment process offers many unique bases for its selection, including: A) Low cost compared to the treatment alternatives; B) Lowest available TCLP leachate levels for any process treating K061. Many other processes leave some residue that represents a disposal requirement, although often not addressed; C) Produces minimized final waste disposed, including the fact that the total volume of dust generated and less than the volume occupied by the residue slag from HTMR; and, D) Opportunities for the beneficial utilization of part or all of the waste stream through the development of chemical and physical characteristics. Each of these aspects will be specifically discussed in the paper, including that status of the operations now under permit.

Jan 1, 1994

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013

By Ruirui Wei, Mingrui Yang, Xuewei Lv

Copper slag is a by-product obtained during smelting of copper from copper ores. In China, for one ton of metal production about 2.2 tons of copper slag was generated, and approximately 15 million tons slag is produced in 2013. Dumping and disposal of such huge quantities of slag will cause environmental and space problems. Most importantly, copper slag cannot be made full use of to maximize its value. In this study, copper slag was used to take the place of scrap iron and part of silica in traditional process and to produce FeSi alloy as the main material. Utilizing silica and copper slag as the raw materials and coke as the reducing agent, FeSi45 was produced in the induction furnace. In addition, the effect of different n(C)/n(O) on FeSi45 has been investigated.Increasing n(C)/n(O) is beneficial to form the stable phase of FeSi. Meanwhile, n(C)/n(O) greatly affects the reduction and recovery of silicon than iron. When n(C)/n(O) equals 1.10, the recovery of silicon and iron is about 77 and 95%, respectively.

Mar 1, 2017

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By Wei-Tong Du, Xiao-Ping Liang, Yu Wang

The structural properties for ternary molten CaO–SiO2–B2O3 system with varying B2O3/SiO2 ratios at a fixed CaO content were calculated by molecular dynamics (MD) simulation. The simulation results revealed that with the increasing of B2O3/SiO2 mol ratio, the bond length of B-O was approximately constant at 1.35 Å, and the coordination number for B (CNB-O) was observed to vary from 3.40 to 3.51, and the average angle of O-B-O increases from 105° to nearly 120°, implying that the geometric stability of structure is reducing sharply. AlsoQ3 andQ4 tetrahedral species (tetrahedron with three and four bridging oxygens respectively) decrease with the increasing of B2O3/SiO2 mol ratio, and the proportion of (Q3 + Q4) decrease linearly from 0.6 to nearly 0, suggesting that B2O3 may behave as a network-breaking basic oxide in the CaO–SiO2–B2O3 system.

Mar 1, 2017