Search Documents

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

WMC was a late entrant into Indonesia in mid-1996, but had considerable experience and success in exploring in Asia, particularly the Philippines since 1988. Given the geological similarities to the Philippines and IndonesiaÆs superior æcradle to graveÆ Contract of Work (CoW) tenure system, the entry into Indonesia was a logical decision but nonetheless a result of detailed planning. At the time of WMCÆs entry, Busang in Kalimantan was still a 60 moz wonder and the euphoria of this apparent discovery had overflowed into every aspect of exploration. Many junior mining companies and tenement speculators were clamouring for properties in Kalimantan, whilst other serious and capable explorers had to compete for properties and exploration personnel in an era of high and often unrealistic expectations. The picture in late-1998 and through 1999 is dramatically different, as the worldwide downturn in the price of most metals coincides with financial and social crises throughout most Asian countries. The impact of this has been particularly severe in Indonesia and when coupled with the negative sentiment of the Busang fraud has resulted in an exodus of junior companies and also some of the majors. This is understandable given the much publicised social unrest, uncertainty of government, mooted changes to the eighth generation CoW, increasing illegal mining and heightened community expectations. The reality however is somewhat different and although clearly a crisis in many respects, it is also a time of great opportunity.

Jan 1, 1999

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By H. C. M. Gordon

IN every co al mine the hazard of fire in the underground workings is always present. This is a natural condition, because the mineral wrought and the supports normally used are themselves combustible and because underground fires may originate in many ways. The main causes of such fires are: (1) Open lights igniting gas, wood, or the coal itself. (2) Explosives igniting gas or coal. (3) Spontaneous combustion. (4) Electric sparks or short circuits igniting gas, wood, or coal. (5) Frictional heat igniting wood, coal, or oily material. (6) Explosions of gas or coal dust igniting wood or coal. The relative importance of these causes, and others less frequently met with, varies from district to district and depends to a great extent on the equipment and supplies used, on the training and discipline maintained among the workmen, and on the liability of the coal to heat spontaneously. It follows, therefore, that open lights should not be used and that, wherever there is the least possibility of methane being encountered, only locked safety lamps of an approved type should be allowed underground. It follows, also, that only 'permitted' explosives should be used and that the it use should be confined to conditions under which they are ?permitted?. Similarly, electric equipment should be of an approved type and all such stationary equipment should be housed in well-ventilated fireproof rooms. Such rooms, as well as entries to stables and oil houses, should be provided with doors which can be easily and tightly closed and which should be constructed of fireproof material.

Jan 1, 1937

By Paul Guliov

Preliminary investigations of stone resources were conducted in the La Range, Johnson Lake-Pelican Narrows-Deschambault Lake and Creighton-Amisk Lake regions of Saskatchewan. The work identified a rich variety of accessible, attractive and technically promising stone resources. Ordovician dolomites in various combinations of red, buff, yellow, grey and purple are very dense and take a very good polish. These are classified as marbles in the industry and some rival the famous marbles of Verona, Italy. A wide variety of attractive granites have been identified. Among these is a jade green stone (charnockite) and ornamental banded granites (gneisses). A dark greenish to black stone (amphibolite) with white and red veining resembles the well-known Verde Antique variety of Vermont and Italy and surpasses it aesthetically and in engineering properties. Some of these stones have been displayed at Canadian and United States expositions where they received an enthusiastic response from the international stone industry. More detailed evaluation and test quarrying of promising deposits are required. Such work could be rewarding to the industry as some stone varieties in the province have the potential for gaining international markets.

Jan 1, 2001

By M. Z. Emad, Y. Majeed, G. Rehman

Massive deposits of rock salt are mined in the Salt Range area of Pakistan. The main export products of rock salt include salt lamps, blocks, and tiles, while local consumption includes the chemical industry and domestic use. The profitable production of salt for value addition depends on the quality, size, and shape of the block. Salt processing for value addition is easier when very few cracks are present in the blocks. The current salt mining practice involves drilling and blasting, which introduces undesired fractures in the material. This paper focuses on the extraction of rock salt blocks by applying conventional cuboidshaped block mining methods used in quarries. The techniques include wedges and feathers, expansion chemicals, and blasting with low-yield explosives. Experimental work involved both laboratory-scale and in-situ field testing. Laboratory experiments assisted with the determination of splitting force, loaddeformation curves, and other rock mechanics parameters. Regression analysis proposes a relationship for the estimation of radial strain from the load in the case of the wedges and feathers method. The splitting force obtained from the laboratory tests was used to confirm the accuracy of the already published empirical relationship. The results of the laboratory as well as in-situ tests showed that the wedges and feathers technique is the most suitable method for mining rock salt blocks of the desired size, shape, while minimizing cracking.

Mar 2, 2022

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957

By Zhenyu Han, Dion Weatherley, Ruslan Puscasu

"This study aims to demonstrate the capacity of the Discrete Element Method (DEM) to model and simulate fracture in brittle rock, capture the crack propagation process and determine crack propagation rates for various levels of external loading. In the numerical experiments reported here, a macroscopically homogeneous body of brittle rock, containing a single pre-existing crack, was subjected to tensile stress loading. Simulations concerned with model I crack growth process in 3D were carried out. The process of fracture has been observed under various steady state and dynamic conditions. The numerical results obtained reproduce qualitatively and quantitatively a variety of observed fracture phenomena. Specifically, this study examined the onset of cracks, single dominant cracks that grow across the specimen, crack bifurcations and branching. The density of fractures that can be nucleated and grow to a significant size with and without arresting each other, crack growth speed and stress distribution, all have been consistently and systematically analyzed. Suggestions on potential future developments are made and discussed.INTRODUCTIONFracture and failure mechanics are very important in mining, manufacturing, materials processing, mineral processing, civil and mechanical engineering, and many other disciplines of science and engineering. Yet, due to the complexity of fracture phenomena, no theoretical models of broad applicability are currently available (Bieniawski 1967). The simulation of crack propagation is therefore considered an open question in numerical rock mechanics. Although, a significant body of experimental research on fracture of materials was carried out since the early days of fracture mechanics (circa 1940s) (Poncelet 1946, Mott 1948), often in parallel with the development of fracture mechanics theories as well as with the development of experimental and observational techniques themselves, the experimental results were often done on particular classes of material such as glasses and other very brittle materials. Indeed, a number of specific experimental observations on the behavior of growing cracks in brittle materials were made in the 1940s for which generally accepted explanations based on physical principles are still lacking. Likewise, quantitative numerical modeling, based on both continuum and discrete methods, as a basis for understanding dynamic crack growth is still in a preliminary stage."

Jan 1, 2015

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By M Warnken

Major cities are not only the focal point for AustralianÆs work, leisure and homes, they also are the focal point for the flow of resources into the built environment, motor cars and transportation and urban consumables. The steady increases in æstockÆ and waste generation, in line with GDP growth, means that cities will become the mine sites of the future if the inherent value is recovered from these materials at end of life. The urban waste stream can be characterised as containing approximately nine per cent hydrocarbon-based materials; 57 per cent biomass-based material; 28 per cent fully mineralised materials that are inert, five per cent metals and less than one per cent of problematic materials that are potentially hazardous and toxic. In order to convert these wastes into value added inputs into the economy, a number of technological interventions are required. These æurban waste mining techniquesÆ revolve around source separation and material streaming. One issue that needs to be overcome when determining which mining technique to implement, is identifying the option that will deliver optimal value, both from a financial and a sustainability perspective. The difference between embodied energy and calorific value is a case in point. Highest net resource value (HNRV) is a concept that can assist in choosing between different resource recovery options. The assessment can be done at a strategic level, or can be used to work out material specific issues. For example, used tyres can be recovered for their energy content at an approximate cost of $120 per tonne, whereas mechanical processing of used tyres can deliver a net benefit of $192.

Jan 1, 2006

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By F. J. Plecity, J. T. Michalak, W. C. Leslie

W. M. Williams (McGill University)-The authors are to be congratulated on completing this detailed investigation of recrystallization behavior. The present writer has recently completed some research at the University of Toronto on the recrystallization and grain growth behavior of a number of "pure" irons, and he would like to take issue with the authors' contention that recrystallization cannot be followed by means of hardness measurements. Two series of specimens of Ferrovac E, a com- mercially available iron, were annealed to complete recrystallization at 525" and 620" C, measurements being made both of Rockwell hardness and of volume percent recrystallized as a function of annealing time. Good correlation was found between these two quantities and, following the earlier practice of Cook and Richards for copper, hardness measurements were used in an extensive investigation of recrystallization. No anomalous behavior was observed as a result of this practice. Specimens which showed complete softening always showed, (metallographically and by X-rays), completely re-crystallized structures. These observations do not, of course, detract in the least from the results of the work under discus-

Jan 1, 1962

By L J. de Lange

As a material asset for mining entities, the resources and reserves (RR) estimation processes are surprisingly underrepresented in the assurance landscape. When press reports expose them being inaccurately reported, or in merger and acquisitions processes, their importance becomes clear. The impact of erroneous RR numbers (both positive and negative) could have a material impact on an entity’s reputation and value.The technical nature and ‘black magic’ connotations of the RR estimation processes are possibly reasons why audit committees are not actively involved with it. Internal auditors avoid the RR processes for similar reasons. Also the traditional approach to obtain assurance on RR is expensive and is therefore only performed when it is absolutely required.However, stakeholders’ expectations of good governance are growing. Part of this increased focus is based on attaining a higher degree of certainty about the current and forecasted position of the entity. Stakeholders are also increasingly more interested in non-financial areas of entities, as the future success of an entity is more than a set of financial metrics.Consequently, the RR estimation processes should be visible on the agendas of audit committees. Monitoring of key controls is required as part of the governance obligations for senior management and the audit committee. So once it is on the audit committee’s agenda, the question then becomes, how will that agenda be supported by an assurance process that is cost-effective?The main objective of the paper is to describe a model of RR assurance that has been effectively applied in some mining companies. The paper discusses one particular approach that provides an audit committee with the required assurance regarding RR processes. The approach ties the assurance needs of the audit committee to the needs of the technical experts in the entity, therefore involving two important figures. It also offers assurance providers with a model to audit ‘through’ the RR processes rather than ‘around’ them. The paper then discusses top-down and bottom-up approaches that provide assurance at different levels of an entity.A governance audit that focuses on the RR processes is suggested as a top-down approach. A bottom-up approach assesses the design adequacy of internal control processes. A hybrid model is described which meets the needs of diverse stakeholders including the audit committee and the RR community.The hybrid model combines the expertise of professionals in both internal audit and RR. The right balance of these skills directed by a singular approach ensures that a credible result is achieved.This approach is not as expensive as some verification approaches used in the industry and can, as a result, be performed on a more regular basis.The last element of the paper looks at implementation of the reporting mechanism. An assurance process aimed at continuous improvement further enhances the robustness and reliability of RR reported by an entity.CITATION:de Lange, L J, 2016. Resources and reserve assurance processes – a framework for improved governance, in Proceedings International Mine Management Conference, pp 21-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By D. T. Randall

Several years ago investigations were begun by the United States Government to determine the most efficient methods of utilizing the coals of the United States. These investigations, which were continued along several different lines, are now being carried on by the Bureau of Mines, in accordance with the provisions of the act creating this bureau . . It was because of the need for more complete information concerning the conditions under which coal could be economically burned in boiler furnaces without objectionable smoke that tests were made at the Government fuel-testing plants at St. Louis, Mo., and Norfolk, Va. In addition to this experimental work a number of commercial plants in the larger cities were inspected to ascertain what were the best methods then in use for abating smoke. The results of these investigations were reported in Bulletins 334 and 373 of the United States Geological Survey. Because of the continued demand for the information contained in these bulletins, the original editions of which are exhausted, they are reprinted by the Bureau of Mines. The text of this bulletin, particularly the information relating to smoke ordinances, was revised in the latter part of 1910 and the early part of 1911 by S. B. Flagg, engineer, who has charge of the steaming tests being conducted by this bureau.

Jan 1, 1912

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By H. J. C. MAC DONALD

THE mining engineer must have a chest of books snug enough for a camelback or to be stowed away in a canoe; at the lowest possible cost, as he needs it the most in those early years when he earns the least; but at the same time one having an unusually wide range, for he may have to cut down a forest, put up a sawmill, build mine towns, construct dams, power houses, power lines, and railroads. In fact he may be called upon for many unexpected accomplishments and all in extension of the characteristically broad demands of his profession. Suppose that an average mining engineer with a thorough theoretical training and a specialized mining education has accumulated, during a cosmopolitan experience, a complete and up-to-date library, but, unfortunately, in accepting a long term assignment to a far country he is forced to discard the greater part of

Jan 1, 1925

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth's crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974