Search Documents

By Hugo Julien

According to OSHA 29 CFR Part 1910.119 (Process safety management of highly hazardous chemicals), Canadian Provincial Safety Standard Acts or Federal laws, the owner of stationary equipment (Boilers, stacks, piping, pressure vessel, etc.) should follow a complete inspection plan and follow an Integrity Operating Windows (IOW’s) adapted for each of them. Some important variables shall be included in the inspection plan such as specific damage mechanisms versus alloy used in the original design, process conditions, etc. Some North American’s standards exist, like the one listed in ASME PTB-2-2009, to help owner to create such inspection program. The new API RP 584, Integrity Operating Windows (IOW’s) can guide Mining & Metals owners to find out their specific IOW’s. Inspection frequencies are often described in the Jurisdiction Safety Acts such as the British Columbia B.C. Reg. 104/2004, etc. but often left in the owner representative responsibility (Bill C-21, federal Act to amend the Canadian Human Rights Act). Every deficiency should be repaired according to recognized Codes such as ASME PCC-2, etc.. If flaws not conforming to the original Code of construction are found, this article will introduce the Fitness-For- Service assessment principles to be able to accept it without any repairs.

Jan 1, 2014

By Solomons S. S, Tillmann V. H

The progress of longhole open stoping (LHOS) at Zinc Corporation Limited and New Broken Hill Consolidated Limited (ZC/NBIIC) is described together with the design of a novel sloped wall longhole stoping method which should allow the complete extraction of the orebody without the formation of pillars and with minimal dilution of the ore with sand fill.

Jan 1, 1981

By Henri Fredriksson, Rami Saario, Mark Weatherseed, Juri Matinheikki

"The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value. With regard to solvent extraction, the introduction of an innovative modular plant design will help to address these issues. The first such modular offering is Outotec’s VSF®X modular solvent-extraction plant that uses prefabricated and transportable modules. Reuse and recyclability have underpinned the design concept. The greatest advantage of the VSF®X modular solvent-extraction plant is its relocation possibility. Additionally, it is suitable for various metals and plant capacity is adjustable through a scalable modular structure. After a dedicated plant lifecycle, the plant can be dismantled and relocated to a new site. This reuse ability offers major benefits for short-term plants, making them more feasible due to higher residual value. A net present value analysis is made for two examples, a conventional plant with no relocation possibility and a modular movable plant with extended plant life cycle, in order to evaluate the feasibility of modular plants. Results indicate that modular plant design could offer an economical solution with the additional advantage of improved overall sustainability through its life cycle. INTRODUCTION The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value (NPV) (Mudd, 2010; Norgate & Jahanshahi, 2010) . Awareness of sustainability issues is also rising and sustainability reporting is now a key element of many companies’ public and investor relations. Major companies are now putting more effort in this area to earn legitimacy for new projects (Mudd 2010)."

Jan 1, 2015

By Wolfram Schnabel

Recently Lurgi has succesfully commissioned Peru's first direct reduction rotary kiln at SIDERPERU?s Chimbote works. The order included comprehensive engineering services and supply of special equipment to modify three existing cement kilns according to the SL/RN process. The kilns were cut to 62m length and installed with a slope of 2.5%. A new heating system, including shell burners, was supplied and inlet and outlet ends of the kilns completely renewed. Figure 1 shows the kilns after modification.

Jan 1, 1981

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920

By D. C. Shumway

Recently, the health of the cement industry has been threatened by the impact of environmental regulations, over-zealous state and federal agencies and radical environmental groups. Unfortunately, cement plant operations tend to trigger every environmental regulation and program promulgated, plus several programs designed specifically for the cement industry. These environmental burdens come at a time when the cement marketplace has been impacted by imports resulting in a situation where it has been difficult to increase prices to offset these increased environmental liabilities. The competitive world market forces the cement industry to seek creative ways to reduce costs. With additional major environmental programs coming down the pipe, like the Federal Clean Air Act Amendments of 1980 and EPA regulation of cement kiln dust, the cement industry has attempted to try innovative supplements to cement manufacturing. The cement industry has found that using waste tires, biosolids and other solid wastes in the cement manufacturing process can reduce costs and plant emissions.

Jan 1, 1996

By E. LaRocque

Denison Mines Limited has been processing uranium ore in the Elliot Lake area for the past 20 years. As the original concept of uranium processing has been modified somewhat over this period, the present paper will describe the current recovery practices at the Denison mill from crushing through concentrate drying and packing . Special emphasis will be placed on the leaching, ion exchange and precipitation sections of the process, with consideration being given to the entire circuit. Descriptions will be given of equipment now being used and control strategies will be discussed.

Jan 1, 1979

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By O. Moselhi

The purpose of this research is to evaluate the impact of Building Information Modeling (BIM) on Just-In-Time (JIT) material delivery, with a focus on how the use of BIM can help improve efficient implementation of JIT and reduce the cost of material management. Previous research and a number of case studies have addressed the positive impact of BIM on construction at large but none focused on JIT in construction. This paper presents a methodology for selecting reliable material vendors. It also utilises the integration of BIM and scheduling software to generate quantities of material and its required delivery time to improve the flow process and improve its reliability to minimise related delays and productivity losses arising from idle and non-productive time of equipment and labour on jobsites. 4D visualization is utilized to support coordination and timing of JIT material deliveries in an effort to minimize congestion on job sites. Case studies on JIT material deliveries are presented and the impact of BIM implementation on reducing the cost of material management is evaluated. The joint effect of BIM and JIT on quality control, elimination of waste, reduction of inventory buffers, and on relationships with material vendors are evaluated by analysing and comparing data from case studies. The paper also presents a methodology based on multi-attribute decision criteria for modelling the selection criteria for material vendors. The model can assist in ranking vendors not only based on cost and quality but also on their reliability in delivering material on time.

Aug 1, 2013

By Alexander Scheuermann, Martin D. Larisch, David J. Williams

"Drilled displacement piles (DDP) have been used around the world for decades as foundation elements for structures and embankments. Typically the pile toes are designed to penetrate into stiff or dense soil formations to achieve sufficient base resistance. Recent research at The University of Queensland in Brisbane, Australia has discovered that the in situ stress conditions in stiff to hard clays is directly related to pile installation rates, which in turn are a function of the piling rig capacity and ground conditions. With adequate and constant pile penetration rates in situ stress conditions in the stiff to hard clay are increased by about 40%, resulting in significantly higher pile capacities. If pile penetration rates are too slow the in situ stress conditions are reduced considerably by remoulding and shearing of the clay, potentially causing reduced pile capacities. The paper presents the results of full-scale test piles at a stiff to hard clay site installed using different full-scale piling equipment.INTRODUCTIONDrilled displacement piling (DDP) is a piling technique in which a hollow stem, fitted with a purpose built displacement tool at the bottom, is drilled into the ground. Dissimilar to non-displacement piles, like Continuous Flight Auger (CFA) piles or conventional rotary bored piles drilled with kelly bars, the soil is not excavated during the DDP penetration process, but is displaced laterally and to a lesser extent vertically. The cavity created by the drilling tool is filled with highly workable concrete during the extraction process. The DDP technique is very economical providing high production rates and creating only marginal drill spoil, which has led to its increased global usage during the last decade. The typical DDP installation process is described in Figure 1."

Jan 1, 1900

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

Identifying Opportunities to Reduce the Consumption of Energy Across Mineral Processing Plants

Sep 13, 2010

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By W. W. Cotter, W. R. Clark

Jan 1, 1946

By D. S. Speakman

The copper-zinc orebody at Sherritt Gordon's Ruttan Mine occurs in a structurally complex area of the Rusty Lake greenstone belt in northern Manitoba. Problems in interpreting drill results indicated a large deviation, and the structural complexity an erratic deviation, of drill holes. This was confirmed when a surface hole was intersected 420 feet to the left of line on the 800 level. This problem acted as a catalyst in promoting a search for a suitable down-hole survey method. The instruments investigated included magnetic multishot and gyroscopic units as well as the ABEM Reflex-Fotobor. Only the Fotobor came close to meeting the company's needs of simplicity, reliability, accuracy and ownership. In this paper, the methods of operating this instrument, as well as the data extraction and reduction techniques, are described. Data on the accuracy and repeatability of the instrument are presented, and a tabular presentation of the results of surveying on 86 holes totalling 64,000 feet of drilling is made. Preliminary statements of the results of ongoing research on causes of hole deviation are presented and recommendations for minimizing deviation are given. The use of the survey device is recommended in areas of structural complexity, for very steep or backsight holes and where expected ore intersections are missing.

Jan 1, 1978

The mineral chromate is the sole current source of commercial chromium Chromite varies compositionally within limits permitted by the formula ((Mg,Fe,Zn,Mn)(A1,Cr)2O4) No chromate has been mined in the United States since 1961 In the past, almost all the chromate mined in the United States came from Alaska, California, Maryland, Montana, Oregon, and Pennsylvania, with about one-half of all production coming from Montana Primary chromate deposits occur only in certain kinds of ultramafic or closely related anorthositic rocks The two major types are stratiform (layered) and pod-shaped The Stillwater Complex of Montana is the largest known United States resource It is a stratiform deposit where several exposed zones of high-iron chromiferous material extend in length Since there is no commercial chromate mining in the United States, there are no environmental problems related to underground mining

Jan 1, 1975

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002