Search Documents

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By G. H. Gronhovd, W. H. Oppelt

Complete gasification to produce synthesis gas for manufacture of synthetic chemicals and fuels offers possibilities for utilization of the vast lignite fuel deposits in the U.S. The design of a slugging, fixed-bed, pressure gasification pilot Plant is described. Results are presented for initial operation of the plant at moderate pressure and using low-temperature char as fuel. Gasification of solid fuels is becoming increasingly important in the future overall energy picture, both in this country and abroad. Snythesis gas from gasification of coal consists chiefly of carbon monoxide and hydrogen, and after suitable purification and modification this gas can be used in the production of synthetic ammonia, methanol, higher alcohols, and synthetic liquid fuels, or as a reducing gas in the metallurgical field.' Most synthesis gas used in this country is made from natural gas, petroleum oils, and refining tail-gases, but the direct gasification of coal will become more attractive as costs of petroleum oils and natural gas increase.' A gasification process designed for use with brown coal and lignite was developed by the German Lurgi Co. prior to World War 11. In this process a fixed bed of lump-sized fuel is gasified with steam and oxygen at pressures ranging from 370 to 440 psi. Effective heat exchange between the ascending high-temperature gases and the descending solid fuel results in low gas outlet temperatures, high thermal efficiency, and favorable oxygen consumption. Lurgi gasifiers are used commercially for the production of synthesis gas or as a substitute for coal gas in many countries, including Germany, Czechslovakia, Great Britain, South Africa, Australia and Pakistan.3-6 The chief disadvantage of the conventional Lurgi gasifier which operates under nonclinkering conditions is that large quantities of excess steam must be supplied with the oxygen-steam mixture to reduce the temperature in the fuel bed below fusion temperature of the ash. Most of the steam leaves the gasifier undecomposed with the product gas and, after cooling, produces large amounts of dilute liquor. Evaluation of fixed-bed gasification experiments using dry-ash removal indicated that by increasing the oxygen concentration in the oxygen-steam blast the temperature in the combustion zone could be raised high enough to operate under slagging conditions. 7-8 Operation of a fixed-bed pressure gasifier under slagging conditions would reduce the steam requirements and the volume of waste liquor and would increase the steam decomposition, the overall thermal efficiency of the process, and the rate of gas production per unit cross sectional area of the gasifier. Because the Lurgi gasification process, modified for slagging operation, offered possibilities for efficient gasification of American lignite, the Bureau of Mines decided to investigate the process on a pilot-plant scale at the Grand Forks, N. D., Lignite Research Laboratory. DESIGN Description of Pilot Plant: A flowsheet of the Grand Forks slagging gasification pilot plant is presented in Fig. 1. The gasifier unit consits of the coal lock, the gas generator, and the slag lock. The fuel, which is periodically charged to the coal lock, moves by gravity flow into the generator and is continuously gasified by an oxygen-steam mixture introduced at the bottom of the gasifier. Molten slag is formed at the hearth and flows through a central taphole into a water quench bath. The slag-water slurry is periodically discharged from the slag lock. Process steam is generated and superheated in separately-fired, oil-burning units. Oxygen is supplied to the gasifier from a gas storage bank located some distance from the pilot plant. The capacity of the oxygen storage bank is about 130,000 standard cu ft at 2200 psig. Liquid oxygen is delivered by truck and is converted to gas during the filling operation. The superheated steam and oxygen are metered separately, then mixed and fed to the gasifier tuyeres. The gas generator is surrounded by a water jacket. The steam formed is separated in the steam drum and then discharged to the gas offtake, thus equaliz-

Jan 1, 1961

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By W. N. Poundstone, G. R. Spindler

A comprehensive report on extensive experimentation in degasification of the Pittsburgh Coal seam is presented. Detailed accounts of the procedures and results are given for permeability tests, vertical bore hole tests, measurement of gas flow from sealed drainage areas, horizontal rib hole tests, and water infusion tests. The removal of methane gas from coal seams in advance of mining is not a new idea with mining men—much attention has been given to the possibility for many years. In other parts of the world, a principal concern has been in the recovery and utilization of the gas and a number of successful projects have been developed in Europe and elsewhere. In this country, the principal motivation has been related to the safety aspect with some possible side benefits concerning costs and efficiency in mining as secondary objectives. To date, experimental work in this country has been largely or entirely exploratory to determine bed characteristics with respect to the liberation of combustible gases to investigate or establish the possibility of degasification in advance of mining and as an aid in projecting mine ventilation systems to provide for safe, effective and economical handling of combustible gases liberated during mining. With these objectives in mind, the School of Mines and Engineering Experiment Station at West Virginia University, in cooperation with the Christopher Coal Co. of Osage, W. Va., initiated some experimental work in May 1952 and the project has been more or less continuous since that time. The work has been centered entirely in mines of the cooperating company in Monongalia County, W. Va., and Greene County, Pa. LOCATION AND GENERAL CONDITIONS OF THE AREA The principal mining in the area involved is in the Pittsburgh coal seam which lies at the bottom of the Monongahela series of the Pennsylvanian. The Pittsburgh coal in the area is generally uniform in its structure and physical characteristics. The bed thickness averages about 7 to 8 ft and the coal has a characteristic blocky structure as the result of pronounced face cleats and definite, but somewhat less pronounced, butt cleavage. It is a medium volatile coal, averaging about 37 pct, and is marketed principally as a steam fuel and for metallurgical purposes. The Pittsburgh coal outcrops along the Monongahela River and dips gradually, but not uniformly, slightly north of west (about N75°W). The westward extensions of the bed, from the areas contiguous to the Monongahela River which have been heavily mined, constitute the principal reserves and are all well below drainage with the depth of cover increasing with the distance from the river. In general, with deeper cover, it may be expected that methane liberation will be more of a problem in future mining as compared to areas mined previously; therein lies the interest in possible de-gasification in advance of mining. Fig. 1 shows the Pittsburgh coal area in the vicinity of Morgantown in Monongalia County, W. Va., and Greene County, Pa., in which the experimental work discussed is located. Fig. 2 shows the contours on the Pittsburgh coal in the test area. It will be noted that the first two bore holes for the experiments were at the edge of a bench or terrace with considerable change in the gradient in the immediate vicinity of the test holes and that the same general condition applies to later test areas. Mining is intensively mechanized in the area and in the mines involved in the experimental work with corresponding rapid advance of working faces a typical characteristic. In the areas now mined the total methane liberation ranges from moderate to relatively heavy, but the actual face liberation is extremely variable and may range from practically

Jan 1, 1961

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By J. D. Allen

In the coal preparation plant at U.S. Steel Corp.'s Concord mine in Alabama, the product moisture was reduced from about 20% to 9% through the development of a workable flowsheet for dying the clean coal. Some of the high points of the conversion of the Concord washer from vibrating screen dewatering to centrifuge drying are presented in this article. The coal preparation plant at the United States Steel Corp.'s Concord mine near Bessemer, Ala., began operations in June, 1950. The basic cleaning circuit consisted of a Chance cone for cleaning the 2-in. x 3/8-in. fraction and concentrating tables for cleaning the -3/8-in. coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable with 85% passing 3 mesh and 25% passing 28 mesh (Fig. I), a considerable quantity of fines passed through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-ft-diam hyd rose para tors from which the underflow returned to the dewatering screens and the overflow went to a 175-ft-diam thickener for water clarification, as illustrated in Fig. 2. As might be expected, there was considerable recirculation of the -35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20%. Further reduction to approximately 11% was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a relatively small percentage of the over-all coal mix at the coke plant, its high moisture and fluctuations did not seriously hamper coking operations. Early in 1964, however, the proportion of Concord coal was increased with a resulting increase in the moisture of the total coal mix, and this caused difficulties in the coke plant. The increased participation of Concord coal also brought about a shortage of railroad cars which raised the moisture content to a point where the coal became almost impossible to handle. In an effort to alleviate this problem, U.S. Steel initiated a research program to develop a flowsheet for reducing the moisture to approximately 10% and to determine whether the resulting product would be satisfactory for the coke plant. Under this program, an experimental flowsheet for evaluating both a vibratory centrifuge system and a solid bowl centrifuge system was drawn up as shown in Fig. 3. A horizontal vibratory centrifuge was installed to reduce the moisture in the dewatered coarse coal, and a four-cell, flotation machine was installed to clean the -65-mesh portion of the 3/8-in. x 0 table raw coal feed. Several shortcomings in the above circuits were apparent. For one thing, large quantities of repulping water were required. Furthermore, since about half of the flotation feed was of a size consist that could have been cleaned on the tables, these circuits would result in an unnecessary increase in reagent costs and facilities. Maintenance of the hydro separators and pumps for pumping the underflow to the filters,

Jan 1, 1969

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880's, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940's. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

A new test coke oven of seven cubic foot capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from the flues on either side of the charge. The method of charging permits close control of charge conditions'such as bulk density and moisture content. These conditions, as well as coking conditions (e.g. flue temper- atures., coking time) must be varied to simulate conditions in different batteries, The effects of several variables on coke quality are discussed. Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes; for 17 tests, the average A.S.T.M. stability and hardness indices for the test oven coke were 38,5% and 69.7%, while those for the battery coke were 37.1.% and 67.6%.

Jan 1, 1969

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969