Search Documents

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By S. M. Bradshaw

The principles of microwave heating are discussed with reference to dielectric properties, heating phenomena and microwave equipment. Microwave regeneration of granular activated carbon for the carbon-in-pulp process is examined on a laboratory scale, with special attention being given to highlight the problem areas and specific considerations related to microwave heating. Results indicate that microwave regeneration of carbon with 40% moisture on a wet basis by heating to 650°C with steam addition regenerates the carbon to virgin carbon activity levels but with a higher abrasion resistance. A preliminary economic assessment showed that the capital cost for 120 kg/h microwave unit would be R540 000 with an annual operating cost of R 320/t carbon. These figures yield a return on investment of 12%. The aim of this paper is to provide an introduction to microwave heating and to illustrate its application to the microwave regeneration of granular activated carbon for the carbon-in-pulp (CIP) process.

Jan 1, 1998

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

The smelting of the Broken Hill lead concentrates at the Broken Hill Asso,ciated Smelters produced, among other products, approximately 4,900 ounces of gold and 8,800,000 ounces of silver during the year ending June 30th, 1938. The following table shows the actual amounts of gold per ton of lead concentrate produced during this period at the important mines. The total gold in the period is calculated from the number of tons of lead concentrates produced, and by comparison with the production' of silver, shows thatthere is no constant relation between the amounts of gold and silver.The fact that no gold is seen during milling, even when gravity concentrating tables are employed, signifies that the gold does not occur as occasional coarse particles.Further, as the values increase considerably in the flotation slime, it can be inferred that the gold occurs as minute inclusions in one or more of the minerals in the lead concentrates.The four most abundant minerals in the lead concentrate are galena, zinc blende, chalcopyrite, and...

Jan 1, 1940

Research into the mechanisation of ore winning from the very narrow reefs characteristic of South African gold mines has been conducted from as early as 1964 through the Chamber of Mines Research Organisation (COMRO) but with limited success. However, the Council for Scientific and Industrial Research (CSIR) has recently re-evaluated the potential for the mechanisation for the narrow tabular gold mines. It has been determined that there are approximately 22 000 tonnes of gold left in-situ in channel widths of less than 500 mm in thickness. The extraction of ore from such reefs requires a complete paradigm shift in that the current mining cycle (drilling, blasting, cleaning and supporting) is not feasible since such a stoping width would not allow the workers entry into the stope. Consequently, a non-entry form of mining is required. With this target in mind CSIR has invested in a project called the Nederburg Miner which seeks to identify new technologies for drilling, rock breaking, cleaning, and materials handling, the application of which will enable non-entry mining of very narrow ore bodies. The intention is to develop a fully automated system that will not require human involvement at the stope face. The outcomes of research into this proposed system will not only extend the life of South African gold mines but will also enhance South Africa's reputation for excellence in mining research. This paper presents the new technologies under consideration and potential methods for their application into an integrated non-entry mining system.

Jan 1, 2008

Adhesion of Escherichia coli onto Oxide Minerals - Extended DLVO Theory and Flotation Behaviour

Sep 13, 2010

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Walt Meglasson

The Kaiser Aluminum Company Smelter, one of several in the Pacific Northwest, was built in 1942 and operated by the Olin Company during World War II and then purchased by Kaiser Aluminum after the war. At its height, the facility employed over 350 workers and was capable of producing 73,000 tons of aluminum per year. It was closed in 2000 through a combination of rising electrical and labor costs, and the inability to compete with more up-to-date foreign facilities.

Jan 1, 2008

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By Sherwin F. Kelly

Twenty five years of exploration has shown that the "geophysical dollar" is worth $1780 in the Orange Free State, $1488 on the Witwatersrand, $85 in Sweden, $28,000 in the Transvaal and $3500 or more in the U.S.

Jan 6, 1951

By K. -H. Lux, Z. Hou

ABSTRACT: It is well known in underground mining and waste disposal that the development of excavation damaged zones (EDZ), and thus, hydraulic pathways, is closely related to the excess in the corresponding damage boundary (= long-term strength) of the rock mass and the resulting damage. By integrating short-term and long-term strength, dilatancy, damage and healing into the newly extended Hou/Lux constitutive model for rock salt, it is possible to treat the tertiary creep, to identify the EDZ around underground facilities and to predict the time-dependent development of the EDZ in rock salt. Under in-situ conditions, the EDZ of a 37-year-old drift at the Sondershausen salt mine and the EDZ around a drift dam in rock salt are numerically examined. The numerical analysis gives satisfactory results. RÉSUMÉ: Dans les exploitations minières et le stockage souterrain des déchets, le développement des zones endommagées et fracturées (EDZ – excavation damaged zone), créant des chemins préférentiels pour écoulement, est étroitement lié au contexte géotechnique et à la méthode d’excavation. En intégrant la résistance court et long terme, la dilatance, l’endommagement et le colmatage, le nouveau modèle rhéologique Hou/Lux pour le sel gemme est capable de traiter le fluage tertiaire, d’évaluer l’extension de l’EDZ et de prédire l’évolution de EDZ dans temps autour des ouvrages creusés dans le sel gemme. L’EDZ d’une galerie datée de 37 ans dans la mine de sel de Sondershausen et les EDZ autour de barrage des galeries dans un sel gemme ont été modélisées. Les résultats numériques fournissent des résultats satisfaisants. ZUSAMENFASSUNG: Bekanntlich ist die Entstehung von Auflockerungszonen und damit hydraulischen Wegsamkeiten in der unmittelbaren Umgebung um bergmännische Hohlräume mit der Überschreitung der entsprechenden Schädigungsgrenze eng verbunden. Unter Berücksichtigung der Bruchfestigkeit, Schädigungsgrenze, Dilatanz, Schädigung und Verheilung kann das Stoffmodell Hou/Lux das Verhalten des tertiären Kriechens beschreiben, die Auflockerungszone im Salzgebirge ermitteln und ihre zeitabhängige Ausdehnung vorausberechnen. Mit diesem Stoffmodell werden die Auflockerungszonen einer 37jährigen Strecke in der Salzgrube Sondershausen und die Auflockerungszonen um ein exemplarisches Abdichtungsbauwerk im Salzgebirge numerisch untersucht. Dabei werden zufriedenstellende Berechnungsergebnisse erzielt.

Jan 1, 2003

By E. Snyders

Two alternative processes for the manufacturing of zircon products were investigated by the South African Nuclear Energy Corporation (Necsa). These were the synthesis of doped-zircon pigments from plasma dissociated zircon, and an upgrading process to convert an inferior grade of zircon into a superior opacifier for ceramic applications. A solid-state reaction process was used to produce doped-zircon pigments. The influence on the colour intensity of the pigments on a ceramic tile were compared for milled and un-milled plasma dissociated zircon (PDZ) material, prior to calcination. Pr-yellow and V-blue zircon pigments produced from PDZ with different degrees of dissociation, were also evaluated. The second zircon beneficiation process entails the upgrading of an inferior grade of zircon to a superior opacifier for ceramic applications. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated.

Jan 1, 2005