Search Documents

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By Lawrence W. Aldrich

At the San Francisco meeting of the Institute last year, I presented, through the courtesy of Dr. James Douglas, some results of experiments on the roasting and leaching of concentrator tailings. After it became apparent that flotation rather than leaching was clearly the better method of handling the particular problem under consideration, before dismantling the experimental equipment, some data were secured on roasting and leaching the concentrate itself in competition with smelting. Some of the results obtained are given in the following paper and they are of particular interest at this time in view of the large quantities of flotation concentrates with their somewhat difficult smelting characteristics now being produced. A complete wet processt consists of roasting and leaching the calcines in dilute sulphuric acid produced from the roaster gases, roasting the residue with salt and leaching with dilute tower liquors (the well-known Longmaid-Henderson process) and recovering the copper, silver and gold by cementation or electrolysis or a combination of both. It is evident, however, that the residue from the first leaching, carrying about 20 per cent. of the copper and all of the silver and gold, can be smelted if preferable. In considering the application of the scheme to individual cases, it must be remembered that freight plays a large part in any reduction process wherein smelting is not conducted at the mouth of the mine, and that it is not practicable today to build small smelting plants for individual operations, The experiments may be grouped under four main heads: Roasting, leaching, chloridizing residue, and recovery of copper from solutions. The products of two concentrators were used: The Nacozari concentrates were the product of a large modern mill not using flotation, the copper mineral being largely chalcopyrite; and the Tyrone concentrates, the product of an experimental mill including flotation, the copper mineral being chiefly chalcocite. Typical analyses are given in Table 1. Fig. 1 shows screen analyses of calcines obtained by dead roasting the

Jan 1, 1917

By R. W. Raymond

PROF. HENRY Louis, of Armstrong College, Newcastle-on-Tyne, England, a distinguished member of this Institute and other technical societies, has recently sent to the Institution of Mining Engineers, and to the Institution of Mining and Metallurgy, in Great Britain, a communication, the substance of which is as follows Prof. Louis calls attention to the absence of any recognized English term for the definite description of a frequent phenomenon-namely, the oblique position of an ore-body in the plane in which it. lies. In this connection, Prof. Louis says that in America the term " pitch " has been occasionally applied to this relation, and proposes that, in the literature of ore-deposits, it shall be hereafter restricted to this particular meaning, the angle of the pitch, like that of the dip, being always measured from the horizontal, and the dip being always taken at right angles to the strike, while the pitch is taken on the plane of the dip, in the direction of the strike. Thus, for example, in a vein or bed striking N-S., and dipping, say, 45° E., there might be an ore-body, the axis of which pitched northward, at an angle of 45° below the horizontal line, as measured on the plane of the inclosing vein or bed. If the term " pitch " had this universally recognized meaning, the situation could be simply and perfectly expressed by its use, in connection with the general data of strike and clip. As Prof. Louis says ?This suggestion has a certain practical value, and is not merely academic. Every mining engineer of practical experience in such types of ore-deposit will have met with cases, in which a vertical shaft has been sunk with the object of cutting the deposit, but has missed it, because the dip alone has been taken into account, while the pitch has been overlooked." He adds the acute observation that such an oversight is much likelier to occur with regard to a condition not definitely desig-

Mar 1, 1908

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By Paul Bechtner

THE name bentonite formerly was applied solely to a peculiar clay occurring in Wyoming and South Dakota, which was distinguished from other clays by its unctuous feel when wet and the property of swelling in water. In the last decade scientific studies of clay have recognized that bentonite is composed mainly of the clay mineral montmorillonite and the name bentonite has been extended to cover the entire family of clays that have montmorillonite as their chief constituent. Montmorillonite has the chemical formula of A1203-4Si0-xH2O, With Fe203 and MgO replacing part of the A1203. The montmorillonite crystal is an Si-Al-Si clay mineral, being formed of two silicon-oxygen sheets with an aluminum-oxygen sheet sandwiched between them. In contrast, kaolinite-the chief clay mineral of most clays other than bentonite-is Si-Al, one silica and one alumina sheet. The unit crystal of montmorillonite is much thinner than that of kaolinite, with greater surface area. These differences in crystal structure patterns are leading factors in the dissimilar properties and commercial uses of bentonite compared with other clays. Mineralogically, bentonites are 85 to 90 pct montmorillonite with fragments of feldspar, gypsum, calcium carbonate, quartz and traces of other minerals. They vary in color; the widely used Wyoming type is creamy white when dry and a light shade of tan when wet; the low-swelling bentonites of the southern United States and elsewhere are found in many shades of gray, blue, yellow, red, and brown. Pure white bentonites are rarer and generally of the medium or low-swelling type, though there are a few exceptions to that general rule. PROPERTIES Bentonites may be divided into two general classes: (1) those that adsorb large quantities of water, "swelling" greatly in the process, and that remain in suspension in thin water dispersions; (2) those that adsorb only slightly more water than ordinary plastic clays or fuller's earths, do not swell noticeably, and settle rapidly in thin water dispersions. Another distinction is that some varieties of the No. 2 type

Jan 1, 1949

By Frank T. Weems

The basic operating properties of the DorrClone are discussed and certain metallurgical applications which exploit these properties are presented. An effective method of controlling the consistency of the DorrClone underflow is described. THIS paper presents in a general manner some of the applications of the DorrClone (Dutch States Mines cyclone) in the metallurgical and heavy chemical fields. Technical or mathematical analyses of the design factors and of the mechanism whereby the cyclone effects its separation have been capably treated in a series of previous papers.'-' Engineering and operational aspects of a few installations and laboratory tests have been chosen to emphasize the unique classification characteristics of the DorrClone and to illustrate its utility in certain difficult situations. Its use in coal washing and heavy-media operations are not considered. Some 25 or more industrial installations and applications of the DorrClone in the metallurgical fields are operating at present, ranging from single trial units to complete batteries composed of a multiplicity of units. The data were obtained in part from some of these, and in part from operations of units at the Westport Mill, the laboratories and testing plant of the Dorr Co. at Westport, Conn. The DorrClone was developed, in principle, by the research dept. of the State Mines, Limburg, Holland, during World War 11. Its first use was to dewater a —50 micron sand used as a dense medium in coal washing. The metallurgical wet cyclone was first publicized by Driessen and Yancey and Geer.6 ince then the cyclone has been studied as a means of de-watering, heavy media concentration, and fine size classification. The DorrClone is shown in Figs. 1 and 2. pulp to be treated is pumped through the feed nozzle, A, into the feed cylinder, B. The feed nozzle is of rectangular cross-section, the outermost edge being tangent to the feed cylinder walls. Feed shims, C, may be attached to the innermost walls to adjust the open area of the feed nozzle available to entering pulp. The tangential injection of feed under pressure supports the vortex action of the pulp that has been detained in the cyclone; the centrifugal forces of this vortex throw the coarse particles to the walls of the cone, D, where they collect and pass downward and out through the adjustable apex opening, E. The fine particles contained in most of the water that entered with the feed pulp move to the inner spiral of the vortex and flow out through the vortex finder, F, contained in the orifice plate, G, which forms the top of cyclone chamber. The overflow pulp may then spray freely into a spray chamber, H, surmounting the cyclone or pass directly into a 90' elbow, I, of somewhat larger diameter than the vortex finder. Installation Where more than one cyclone is to be installed, best overall efficiency and ease of control are obtained with equal distribution of both pulp volume and weight of solids among the cyclones, and with the same pressure being maintained at each cyclone feed nozzle. Fig. 3 is a suggested arrangement for feeding two or more cyclones in parallel. Feed pressure control: Under normal operating conditions it is not unusual for some surge to exist in the feed that is to be sent to the cyclone. As will be discussed later, surges in the solids content of the pulp are usually not of great operational consequence, but surges in feed volume are a problem. Several systems have been devised for absorbing surges in feed volume, each involving a surge tank. If the surges are small and fairly rhythmical, a tank of sufficient size might be installed to dampen out

Jan 1, 1952

By Olav Dalen

A HUNDRED years have passed since Wöhler made the first few particles of aluminum by decompos-ing aluminum chloride with potassium. In 1854 Deville used sodium to decompose the double chloride of aluminum and sodium, but even various subsequent improvements of the process, especially by Castner, did not sufficiently decrease the cost of the metal to bring it into general use. In 1862 Monckton proposed to reduce Al O? with carbon by the aid of the electric current, but the efforts of the Cowles brothers to do so were not successful and in 1884 they turned to making aluminum alloys by electrolysis. At about the same time Hall in America and Heroult in France success-fully worked out the technology of dissolving A12O3 in fused cryolite and electrolyzing the bath. It is hard to realize that forty years ago the annual production of aluminum was only 30 to 40 tons per year and the price of the metal thirty times what it is today. Great strides in decreasing the cost of production, improving the quality of the metal, and increasing the output have been made in the lifetime of middle-aged men. The large consumption of electrical energy in the form of direct current makes it necessary to locate aluminum-producing plants near waterfalls, to avoid transmission losses. Norway with its abundant water-falls is therefore a logical place for the development of aluminum production, even though it is necessary to import the bauxite, which is the raw material of the process. It was foreigners who first started the aluminum in-dustry of Norway and the first two plants were built by the British Aluminium Co. in 1906 to 1908; one at Vigeland near Kristiansand, and the other at Stavan-gerfjord in Nordfjord. These two plants are still oper-ating and producing over 3000 tons a year. When the plant at Vigeland is enlarged the production of the company will be more than 4000 tons a year.

Jan 11, 1927

By MCA Woolsey

(Butte. Meeting, August, 1913.). IN metallurgical circles it is known widely, but somewhat vaguely, that the ease of: reduction of metallic oxides depends largely on the way they have been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction- temperature of zinc oxides variously prepared and of several kinds.1 In said paper it was shown that the temperature it which zinc oxide evolves zinc according to the equation Zn0. +' C = Zn + CO depends upon the ;nature of:., the.' two reacting bodies. The determinations bad a range of accuracy of from 2° to. 6° C.,whereas differences were found to. amount to an extreme. of 90° C. :.86 the differences are real ones and must have, definite cause. The equation of boiling water, (H20)4 = 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. , In general, all equations. reacting e in .the liquid or the gaseous phase have-well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the temperature conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not, a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules.

Jan 7, 1913

By Henry Hibbard

Fox the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seen to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machinery, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume.

Jan 9, 1919

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.' reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

By J. H. Schulman, M. H. Buckenham

Although much interest has been taken in the use of mixed collectors in flotation, this investigation is probably the first in which oppositely charged collectors have been considered. The results obtained and the techniques used could well be applied in the behavior of other mixe the behavior of other mixed collector systems and could possibly explain the effective flotation results which have been reported when various collector combinations have been used. Collectors conventionally employed in flotation systems are soluble in water, but many of their homologs of longer hydrocarbon chain length are insoluble. The properties and behavior of these insoluble compounds may be conveniently studied when they are spread as monolayers at the air/water interface on the Langmuir-Adam trough. Although some extrapolation is involved in applying effects observed at this interface to the solid/liquid interface where the action of collectors is most important in flotation, the technique nevertheless is most useful for the study and interpretation of flotation phenomena. Of particular interest in this field are investigations on the insoluble monolayers of the fatty acids, alkyl sulfates and alkyl amines; the penetration of these insoluble monolayers by soluble surface active components and their interaction with metal ions from the underlying solution.'-' Unfortunately, the insoluble xanthates and related compounds do not exhibit stable monolayer properties due to rapid oxidation at the air/water interface and, therefore, cannot be studied directly in this way. These approaches have enabled Leja and Schulman8 to suggest mechanisms explaining dynamic attachment of mineral particles to air bubbles involving collector-frother interaction and the adsorption of collectors onto mineral surfaces. In this and other papers 9-12 considerable evidence is presented to support the concept of collector-frother and metal ion-monolayer interaction and to emphasize the value of monolayer techniques in elucidating the flotation system. Molecular interactions resulting from monolayer penetration are determined by the nature of and the association between both the polar and nonpolar groups of the two molecules concerned. Stable complexes are formed on penetration when interaction takes place between both the polar and nonpolar groups, and although the resultant complexes are not necessarily true chemical compounds, the properties of the molecularly associated complexes are very different from those of the individual components. Shortening of, or changes from, a straight hydrocarbon chain in one of the reacting molecules reduces considerably the stability of the associated complex as do changes in temperature, pH and substrate composition. The effect of hydrocarbon chain length becomes most important when observed effects are to be applied in flotation studies where soluble homo-logs and, therefore, much shorter hydrocarbon chain lengths are used. The present investigation is based on Langmuir trough work carried out by Bowcott,l3 who studied the penetration of insoluble amine monolayers by potassium lauryl xanthate. Bowcott observed that cetyl amine monolayers were readily penetrated by xanthate, but found that with time the high film pressures resulting from penetration and association fell off, indicating decomposition and ejection of xanthate from the film. This decomposition was pH dependent. Of particular interest in this work were studies on an equimolecular mixed monolayer of the fully N-substituted ammonium compound, for example, cetyl trimethyl ammonium iodide (CTAI) and potassium cetyl xanthate. Despite the fact that the CTAI is water soluble and the xanthate on its own is incapable of forming a monolayer, the mixed film was stable up to a surface pressure of 67 dynes per cm. In this condensed state the xanthate was stabilized against atmospheric oxidation, although iodine injected beneath the film caused an immediate collapse. The stabilizing of xanthate against oxidation by association with an alkyl trimethyl ammonium bromide (TAB) could be important in flotation, and a study of the performance and behavior of mixed collectors therefore was undertaken. A modified Hallimond tube operated under controlled conditions was used to evaluate flotation. Surface tension measurements were made to investigate the properties of the soluble

Jan 1, 1963

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33' API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By E. L. Bruce

GOLD occurs in many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at. Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be conned to representative types of deposits, chiefly those of major importance; a few others, differ-ing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwest-ern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubt-edly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however,, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambriang old deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By Orson Cutler Shepard

The term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 1934l. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner: . . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1939

By Orson Cutler Shepard

The term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 1934l. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner: . . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1939

By J. V. Emmons

IT has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass. Within the last few years it has been generally recognized that many of these properties were clue to surface decarbonization. The origin and effects of this altering of the composition have been but little studied. C. M. Johnson' arrives at the conclusion that, in annealing, "the most active agent in surface decarbonization is the rust or scale (present on the surface), which is actually reduced to metal at the expense of the carbon in the steel to which it adheres." W. H. Hatfield in his admirable paper, The Chemical Physics Involved in the Decarburization of Iron-Carbon Alloys,' has given us the most tenable theory of the removal of carbon from iron. While Mr. Hatfield's work has been principally clone in connection with the annealing of white cast iron to produce malleable castings, it is frequently applicable to the decarbonization of tool steel. The following equations which he proposed have been fully borne out by the author's experiments: 2Fe3C + 2CO2 = 3Fe2 + 4C0 2C0 + 02 = 2C02 Continuous 2C02 + 2Fe3C = 3Fe2 + 4C0 It is the purpose of the author to show, in a quantitative manner, the effect of various treatments in eliminating the carbon in tool steel. Some of the phenomena of the decarbonized surface will also be described, as well as the practical problems they present to. the manufacturer and user of tool-steel products.

Jan 9, 1914

By A. Raman, P. P. Singh

The constitution of the La-Rh system was studied by powder X-ray diffraction, metallopaphic, and differential thermal analysis techniques and an equilibrium diagram is presented. Eleven intermediate phases occur in the system and the crystal structural data for nine of them were determined. La3Rh crystallizes in an orthorhombic structure of undetermined type, whose unit cell is obtained by doubling the 'a; and 'c,,' edges of an FesC type unit cell. The other intermediate phases of the system are LarRh-3( undetermined structures also occur in the system. LaRh, undergoes a polymorphic phase transformation at 1240°C. LaRh3 and La2Rh7 also exhibit polymorphisnz. The phases Laah and LazRh7 melt congruently. The latter undergoes a eutectoid transformation into LaRh, and Rh at 1205°C. Laah3 is formed by a peritectoid reaction between Laah and La,Rh,,. The other Phases result from peritectic reactions between the liquid and the adjacent rhodium-rich phases. The intermediate Phases of the La-Rh system are compared with those of the La-Co and La-Ni systems. DURING the course of a detailed investigation to study the occurrence of CrB, FeB, A1B2, and related structures in the rare earth alloys it was found that much information is lacking for the rare earth noble metal systems. Although the structures of several rare earth alloys containing the noble metals at the AB and AB2 stoichiometries have been reported, the occurrence of related structures at other stoichiometries has not been studied. We have initiated a project to study the crystal structural features of selected rare earth-rhodium alloys and to map the equilibrium diagrams of representative systems with conventional methods. The results of our investigation in the La-Rh system are presented in this paper. Two phases were known in the La-Rh system. LaRh has the CrB-type structure.' LaRhz is a MgCu2-type Laves phase.z EXPERIMENTAL PROCEDURE Alloys weighing less than 1 g were prepared from commercially pure lanthanum (99.9 pct +), supplied by Lunex Company, Pleasant Valley, Iowa, and rhodium (99.92 pct +), supplied by Engelhardt Industries, Newark, N.J., in a conventional arc melting furnace under argon atmosphere. The buttons were turned upside down and remelted three times to insure homogeneity in the samples. Since negligible loss of material was encountered during melting, a chemical analysis of the alloy buttons was not undertaken. Powder specimens for X-ray diffraction studies in the as cast state were then prepared. The buttons were wrapped in thin molybdenum foils and homogenized by heating in vacuum at suitable high temperatures for more than 1 week. They were then broken into three or four pieces for annealing experiments. The pieces were wrapped in molybdenum foils and annealed at various temperatures in evacuated quartz capsules. The annealing was carried out for 2 hr at or above 1200°C, 1 day at temperatures close to llOO°C, 2 days at 1000°C, and for 1 week at temperatures below 1000°C. After annealing the alloy pieces were again broken and powder specimens for X-ray diffraction were prepared. The powders of the lanthanum rich alloys with more than 80 at. pct La were prepared by filing. The filings were sealed in molybdenum tubings and stress-relieved at 600°C in vacuum. It was not deemed necessary to stress-relieve the powders of the other alloys, since the alloys were very brittle and were ground easily. POWDER X-RAY DIFFRACTION X-ray diffraction photographs of powders (-325 mesh size) of the alloys in the as cast and annealed states were prepared in a Guinier-de Wolff focussing camera with copper K, X radiations. These patterns were studied to identify the stoichiometries and the crystal structures of the intermediate phases. The lattice parameters of the phases were calculated after minimizing the differences between the observed sin2 6 values, calculated from the diffraction angles 8, and the sin2 8 values, calculated using approximate lattice constants obtained from a few lines. These differences were minimized manually to less than 0.0005. The latLice constants are judged to be accurate to *0.005A for values less thp about 10A and to k0.01~ for values greater than 10A. The relative intensities of the lines were calculated using a computer program written by Jeitschko and Parthk.~ No attempt was made to refine the atomic positional parameters in the phases. METALLOGRAPHY The phase equilibria in the investigated alloys in the as cast and annealed states were also studied by metallographic examination. The polished specimen surfaces were etched with 10 pct picric acid in alcohol (alloys up to 25 pct Rh), concentrated picric acid (from 25 to 37.5 pct Rh), 2 pct nital (40 to 50 pct Rh), 10 pct nital (from 50 to 66.7 pct Rh) and with concentrated 48 pct HF for the other rhodium-rich alloys. Selected microstruture~ were then photographed using a Po-laroid Land camera. THERMAL ANALYSIS Differential thermal analysis of the alloys was carried out in DTA-668 Stone differential thermal ana-

Jan 1, 1970

By P. Barnes

Several statements have been made to the Institute, somewhat detached from each other, as to the cost of some parts of these works, but they have not included any extended description of the buildings or machinery. The general plan of the work connected with the water supply differs, in some important details, from that which has been common either in the Pittsburgh district or elsewhere, and a somewhat extended description may be of interest to the Institute, in connection with a note of the cost of the work. The plan as a whole, and nearly all the important details, were developed by Mr. William P. Shinn, C.E., the general manager of the Company. The immediate and responsible charge of the work was in the hands of Mr. John C. Lewis, C.E., to whom had been committed all the work of this general description, including the laying out of the whole of the foundations, the erection of the buildings, and the grading and laying down of the entire railroad system. The continuous operation of the machinery and other fixtures of these waterworks, for more than three years, has fully demonstrated the correctness and econonly of the plan adopted. No casualties of any moment have befallen the apparatus, and no improvements have been suggested as important except that the gate at the river end of the conduit should have been made more completely water-tight, so that the whole length of the conduit could be pumped out dry without resort to any temporary dam in the conduit itself. In general terms the works of the Edgar Thomson Company are situated on a plateau, about 52 feet above the low-water level of the Monongahela River, and about 2000 feet from its bank. The site of the works is bordered on one side by Turtle Creek, a small stream which drains a considerable area of coal mining territory. This creek is about 100 feet from the group of buildings which have been erected, but it flows into the Monongahela River at a point, about 1200 feet further up than that selected for the entrance to the waterworks conduit. It was ascertained by analysis that the water in the creek contains an important percentage of sulphate of lime, while the water of the river is of unusual purity, in respect of any salts

Jan 1, 1879

By George S. Rice

A problem of possible subsidence of the surface from mining operations, which might have had disastrous results, arose in 1913 at the Brier Hill mine, of the Penn Iron Mining Co., near Norway, Mich., now managed by Pickands, Mather & Co. for the Bethlehem Steel Co. A double track and sidings of the Chicago & North Western Railroad passed over part of the mine, and if subsidence had reached the surface it might have affected the stability of the tracks. The chief purpose of this paper is to record the facts disclosed by investigations of underground movement from 1913 to 1919, when the tracks were moved, and subsequently at intervals, as engineering data of value from mining carried on below the tracks in the steeply pitching lenses. A secondary purpose of this paper is to describe a novel method for determining the rate of speed of upward breaking above the mine excavations. This method was found effective and might be used elsewhere under similar conditions. The mine workings under consideration were developed from the Brier Hill shaft, which was circular, concrete-lined, 14 ft. in diameter and about 900 ft. deep. They extended about 800 ft. westward from the shaft, and nearly parallel to a corresponding length of the railroad tracks. The highest part of these workings was at a depth of 400 ft. below the tracks (Figs. 1 to 12). The mining company had the right to remove the ore, the railroad assuming that the surface would be supported. Finally, without legal controversy, an amicable adjustment was reached as to what should be done to lessen or obviate the hazard of subsidence. Method oF Mining Before the problem became acute, the mining company, to decrease the possibility of subsidence, had been mining the part of the orebody that lay under the tracks by a room-and-pillar system, back-filling with

Jan 1, 1934