Search Documents

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By M. J. Sheriff, D. H. Smith, W. Macdonald

The paper outlines the basic procedure used in electrical system planning and design. Consideration is given to the use of applicable codes and standards, development and use of a system One Line Diagram, power availability, load requirements and power factor. Also discussed are the factors influencing the selection of power supply and distribution arrangement, voltage levels, system grounding, distribution and utilization equipment such as switchgear, transformers, motor control, cable systems, motors. Short circuit calculation methods and system protection are discussed.

Jan 1, 1978

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

Jan 1, 1887

By C. O. Rison

HIGH explosives, particularly nitroglycerin, have been used in torpedoes for the purpose of shooting oil and gas wells for more than 60 years. The early history of the oil industry in Pennsylvania is not clear as to who actually torpedoed the first well, although in 1865 the Roberts Torpedo Co. procured a patent covering the process. Gunpowder was first used, although nitroglycerin was substituted shortly afterwards. Wells are shot for the purpose of increasing the flow of oil and gas A shot-hole in the producing horizon, with its contributory fissures and fractures, increases the area of and stimulates drainage into the hole. The shot-hole also acts as a collecting basin from which the oil is pumped. As a rule, hard or close-grained sands or limes are shot, other more or less porous and soft formations usually do not require shooting. and might be injured by blasting. Shooting is also resorted to in mechanical trouble such as straightening crooked holes, sidetracking pipe or tools, and for severing frozen strings of casing or drill pipe. Explosives arc also used sometimes to extinguish oil or gas-well fires although that work, which involves unusual conditions and methods, does not properly come within the classification of oil-well shooting. Some Factors to Be Considered in Shooting Wells Although nitroglycerin has been used extensively for more than half a century in shooting oil and gas wells, there is still a great deal of uncertainty as to the proper method of shooting or the amount of explosive required to produce best results in a particular formation. The possibility of shooting unproductive or cavey formations above or below the productive horizons, shooting into lower water, destroying casing seats, and the splitting or collapsing of casing strings, are factors that require consideration. The engineering departments of a number of the larger oil companies are making a study of methods of shooting, and the amounts of liquid nitroglycerin or other explosives required in shooting various productive

Jan 1, 1929

[ ]

Jan 1, 1938

Although the mining industry faced ever-increasing risks and uncertainties in 1974, it nevertheless pushed ahead with considerable rapidity in exploring and developing new orebodies-while expanding and improving the technologies of mining and exploration. Prepared by the SME Mining and Exploration Division, this section of the annual review covers the pertinent worldwide developments in the fields of geochemistry, geology, geological engineering, open pit mining, underground mining, rock mechanics, operations research, and solution mining.

Jan 2, 1975

By Frank F. Poland

TEE purpose of this paper-is to describe a new process for the refining of secondary copper-base metals and a specially designed high-temperature electric-resistor furnace used in the process for the distillation of zinc from these metals. The process was used for the conversion of nickel silver to cupronickel and to recover the zinc content in metallic form. It also proved applicable and economical for the treatment of scrap brass for separating and reclaiming the copper and zinc. The relatively large furnace developed for the distillation of zinc is described in detail, for it made economically possible the direct recovery of metallic zinc from scrap brass, which is a new step in the processing of such material. Considerable interest has been shown in the utilization of the distillation furnace for other metallurgical processes, where it is of advantage to operate in a controlled neutral or reducing atmosphere, or to avoid having the processed metal in contact with refractories other than carbon, or to operate at temperatures between 3000 and 4000°F. PURPOSE OF DEVELOPMENT It was recognized early in the war effort that nickel would become a critical metal, therefore all nickel stock and alloys containing relatively high percentages of nickel were frozen immediately. Among these alloys were considerable quantities of various grades of nickel silver, an alloy containing copper, nickel, zinc, and in some grades lead, also minor amounts of iron, manganese and other constituents. At the time there was no existing plant or process to eliminate the zinc, lead, and minor constituents so as to convert this metal to cupronickel, one of the important alloys needed by the U. S. Navy for condenser parts. Therefore the Bureau of Industrial Conservation of the War Production Board requested the executives of the leading nonferrous metal companies to have their metallurgical staffs study the problem of converting this metal to cupronickel conforming to U. S. Navy Specification 44T40. The composition specified therein is as follows: nickel, 29 to 32 per cent; zinc, 1.00; iron, 0.00 to 0.60; lead, 0.05; tin, 1.20; manganese, 0.00 to 1.00; total of other elements (maximum), 0.50; copper, remainder. The problem in converting these alloys to cupronickel was the elimination of zinc, lead, iron, manganese, and other elements without appreciable loss of nickel to slags or other by-products. Revere Copper and Brass Incorporated, through its Research and Development Department, undertook to solve this problem. A Government-owned plant was built at Rome, N. Y., and there the con- version was successfully made.

Jan 1, 1946

By John Goheen

CONSIDERABLE work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods ¼ in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constructed to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses 2200-2250° F. (1205-1234° C.) Yellow brasses 2250-2400° F. (1234-1318° C.) Bronzes 2300-2550° F. (1260-1400° C.)

Jan 11, 1921

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

By W. Bradley, R. G. Hall

This paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer '0 the Bradley 'lining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a a kiln at the same end—that is, of course, the upper end' This is as opposed to "countercurrent firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. Early References The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,l its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver ... is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and fies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake county, California, The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank, Reed and Sulphur Bank ranked respectively Nth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: of there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of ... the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away, as its richness and value were not

Jan 1, 1949

By J. H. Pratt

In a recent paper* on the origin of corundum associated with the peridotites of North Carolina, attention was called to the constant occurrence of the mineral, chromite, in these rocks. The field-data obtained during the preparation of that paper have been used largely in the present paper. During the past summer the general occurrences of chromite have been carefully studied, and those in North Carolina have been especially examined in the field. It is purposed to give, in this paper, the reasons why the chromite should be regarded as having been formed at the same time with the peridotites, having been held in solution by the molten mass of the peridotite, and crystallizing out among the first minerals as the mass began to cool. This theory is essentially the same as that advanced by me for the origin of the corundum associated with the peridotite rocks, and a similar line of reasoning has been used to substantiate the theory proposed. Investigations concerning the igneous origin of some of the ores have been materially aided, during recent years, by the skillful experiments of Morozewicz and Lagorio,§ and by researches that show us, more clearly, why we should regard a fused mass of rock as a liquid, having similar properties to an ordinary solution. These experiments have shown that a molten basic glass, similar in composition to the basic magnesian rocks, dissolves alumina readily, and that upon cooling, the first minerals to separate out are corundum and spinel.

Jan 1, 1900

By J. D. Jones

Unique aspects of tailing pond design aid reclamation facilities for three separate projects are described.

Jan 1, 1978

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS. ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Fergusson, V. Bir¬mingham, Aldrich, T. H., Jr, Bowron, C. E, Bowron, J., Davis, F H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E, McCormack, G B., McCrery, Ramsay, E, Shook, A. M. Ensley, McDonald, S., Shook, J. W. Gadsden, Lee, R. H., Jr. Gannts Quarry, Hiller, E Helena, Squire, J. Huntsvalle, Moss Le¬high, Toulmin. Ozmoor, Greenamyer, A. G. Rock Run, Garvin, J M. Selma, Saylor, B. F. A. Sheffield, Miller, D, I. Tuscaloosa, Lodge, J. Woodward, Wood¬ward, A. H. ALASKA Coppermount, Wiswell, H. J. Douglas Island, Macdonald, J Ellamar, Stevens, B. Fairbanks, Hamilton, A L Haines, Le Wald, E A. Jualin, Hoggatt, W. B. Juneau, Denby, Hampton, W. H , Thane, B L , Whipple, J. R. Ketchikan, Bar¬ber, J C , Parker, J. L., Reid, G D Nome, Garfield, C D. Snettwham, Tisdale. Teller, Hirshberg, M. R. Treadwell Caty, Kinzie, Stow, H. P. Valdez, Esterly, G. M, Hazelet.

Jan 1, 1910

By R. Hoffmann

The Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1983 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 1, 1979

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By Earl W. Palmer, Cyril Stanley Smith

A study of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. Material Used After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in, in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made on the castings after commercial mallealleizing and after special heat treatments to be described. The analyses of the white irons are given in Table 1.

Jan 1, 1935