Search Documents

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By Paul T. Benson

MOST important of the various departments of a custom smelter, so far as the financial welfare of the plant and the confidence of shippers are concerned, is that responsible for correct weights, accurate moisture sampling, and the obtaining of control samples that are strictly representative of the lot of ore from which they come. Treatment rate schedules are based on the metal content of ores received, reduced to dry weight. These rates must be low enough to keep the ship- per from taking his business else- where and still must allow the smelter a profit. Assay results, likewise, must satisfy the shipper, but if they show too high a metal content for the ore they represent, the smelter will actually lose money. It is always considered, and constant checks through umpire assays prove, that laboratory results are closely correct, so the bur- den of the plant profit and loss and the satisfaction of the shipper rest squarely upon the sampling department.

Jan 1, 1936

By M. G., Corson

1. In addition to the alloys of copper with iron previously found by Hanson and Ford to show an increase in the concentration of the alpha range with increase in temperature the following binary and ternary systems have been found by the author to exhibit: the same feature: (a) Copper-chromium. (b) Copper-cobalt. (c) Copper-silicon. (d) Copper-nickel-silicon and its pseudo-binary section Cu-Ni2Si (formula of compound definitely established). (e) Copper-cobalt-silicon and its pseudo-binary section Cu-Co2Si (formula of compound established with some probability but not as definitely as for Ni2Si). (f) Copper-chromium-silicon; formation of a compound definitely established (compare Figs. 1 and 2). The formula of this compound may be either Cr2Si or Cr3Si. (g) Copper-iron-silicon; presence of a phase containing both iron and silicon established in an indirect way only. No definite microconstituents observed. 2. RANGES OF SOLID SOLUBILITY (percentage at various tempera¬tures). (a) For copper-chromium: 0.8 at 1000° C.; 0.5 at 900° C.; 0.25 at 800° C.; 0.05 to 0.1 at 500° C. (b) For copper-cobalt: 3.4 at 1000'C.; 2.4 at 900'C.; 1.7 at 800'C.; 0.9 at 600°C.; 0.35 at room temperature. (c) For copper-silicon (Fig. 3) : 6.8 ± 0.1. per cent. at 800° C.; 3 per cent. at 400° C. and probably below 2 per cent. at room temperature if sufficiently long annealed. (d) For copper-cobalt silicide: 3.3 at 1000° C.; 2.4 at 900° C.; 1.6 at 800° C.; 0.7 at 600° C.; 0.3 at 300° C. (e) For copper-nickel silicide (Fig. 4): 8.2 at 1000° C.; 5.5 at 900° C.; 3.6 at 800° C.; 1.6 at 600° C.; 0.7 at 300° C.

Jan 1, 1927

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By E. G. SINCLAIR

DRILLING wildcat wells in Wyoming differs a little from methods used in any other field. Here it is always advisable to start the hole as large as is convenient in order to carry each string of pipe as far as possible, so that drilling can be continued a thousand feet deeper if necessary, as there is always sand a few hundred feet ahead that really ought to be tested. This plan may seem ambitious, but if it is adhered to, it will save a great deal of trouble before the well is completed. In making the location, one representative from the operating department and one from the geological department should work together, so that the well may be in the best possible place for obtaining oil and the most feasible place to drill for the operating department. In Wyoming nearly all wells are drilled with standard tools, as with them a better log can be kept and better time made in completing the hole. The shales of Wyoming are very hard and do not mix well in a wet hole. The shale cuts into large pieces, too large to be circulated out of the hole, and forms a mat on the rotary which soon cuts off circulation. Then if this mat cannot be jarred from the bit, the drilling string has to be pulled and the mat cut off from the bit with a pick or an axe. I have seen standard tools come out of a wet hole with 10 to 16 in. of mat on the bottom of the bit. Rotary tools have drilled wells satisfactorily in the Big Muddy field and at Billy Creek, but in the other fields the wells have been drilled much more economically with cable tools.

Jan 1, 1926

By G. V. Smith, C. O. Tarr, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

By C. O. Tarr, G. V. Smith, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

By Clinton H. Crane

IN October, 1925, J. R. Finlay delivered an address entitled, "The Future Price of Lead." Lead was then selling at 8.85c. and Mr. Finlay and most of the rest of us were concerned about the shortage. Now, a little more than six years after, lead is selling for 3.55c., and nobody is worrying about the difficulty of getting plenty of it. For 1931 the U. S. G. S. reports United States produc¬tion as 390,000 tons of recoverable lead in ore. Our estimate is slightly higher than this; nearer 400,000 tons. This is the smallest production since 1911 and 1912, but in spite of this, stocks for the year-have increased nearly 50,000 tons. Our estimate for the production outside the United States is 1,120,000 tons, or more than double the production of either 1920 or 1921, and 30 per cent more than in 1913. Stocks abroad probably have not increased more than stocks in the United States. In other words, foreign consumption is double what it was in 1.920-21, whereas domestic consumption is substantially less. It looks as if Mr. Krueger, president of the Swedish match trust, was right when he said that "This country had better stop worrying about Europe and think a little bit more about its own affairs."

Jan 1, 1932

By Stanly A. Easton, H. M. Childs

Methods evolved at Kellogg have had primarily in view the safety of workmen and complete recovery of the ore; it is believed that these results have been secured at a minimum cost. The ore in the Bunker Hill mine is of good grade, relatively speaking; much of it is quite rich and no mining method would be successful which did not recover all of the ore. It would be possible to work certain of the orebodies by shrinkage methods, or some form of top-slicing, at probably lower costs than by the methods now applied, but the shapes of the orebodies are so irregular that satisfactory extraction of the ore in all its ramifications would be extremely difficult. In past years, much high-grade ore has been lost in blasting, due to the unskilful use of powder in a galena ore, which, by reason of its brittle-ness and great weight, tends to scatter widely. Any method by which large masses of ore and waste are broken together will result in an imperfect recovery of the ore, and whenever large masses are broken, ore and waste will unavoidably fall down together; ore and waste thus become entangled and, although a pile of broken material may seem to have been well picked over, quantities of ore will inevitably be lost. This fact has been shown by persons reworking the filling in stopes that were mined by methods defective in the foregoing particulars. Safety of the men is secured by avoiding large openings, and by working mainly under timber, and at small faces at close range and easily inspected. In former years the principal source of serious accidents was "falls of ground;" it is now over seven years since a serious accident has occurred from this cause. The most prolific source of accidents during recent years has been "timber and tools," workmen being struck by timbers passed into the stope from the level above; this danger has been greatly reduced by compressed-air warning whistles and the fencing in of dangerous areas. The lead-silver ore of the Bunker Hill and Sullivan and affiliated mines is found in bodies of almost every shape, although vertical or nearly

Jan 1, 1925

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle' and in particular for the special case under consideration.1'2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43', 55° 16', 64 3 43 1, and32"26'. These add up to 1802 08 1, indicating a cumulative error of 8'. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43', 55°16'), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By Tegner C. Johnson

Just a few years ago, my company was referred to as the Marion Steam Shovel Company. Though we still make shovels, both two and eight-crawler types, the eight-crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It is popular because it can cope with overburden depths in excess of 100 ft and with blasted sedimentary rock, all at an O & O (ownership and operational) cost of ±10[c] per bank cu yd (bcy).

Jan 10, 1974

By Ralph Arnold

SOUTH of Havana, there is a geanticline that extends from Madruga to Bejucal. The older formations outcrop in the. east and gradually go under until in the Bejucal region the entire geological column lies below the surface, with the Nazareno formation at the top. The well we are now drilling is located at the deepest part of the section. I think there is a good chance to obtain oil, for the conditions are like those in the Santa Maria field in California. In both places asphalt occurs in the upper shales in the form of dikes that break through the older formations. The drilling in the Santa Maria field was brought about by the evidence offered by the asphalt deposit, which overlaid the oilfields. Detailed geologic work in both fields discloses pretty well defined domes with minor faults. Between Madruga and Bejucal, the San Francisco formation has come, to the surface in a dome and still farther east there are other domes near the base of the formation in which the Madruga chalk is the surface rock. The Bejucal dome was selected for drilling because, it gave the greatest evidence of petroleum in the form of asphalt and because it offered three chances of striking oil in the three possible oil horizons below the top of the Nazareno formation. The hole is now 2600 ft. deep and has shown considerable gas and some oil. The lowest gas sand will probably yield from 2,000,000 to 3,000,000 cu. ft. per day. Very heavy mud has been used in drilling this hole and this has held back gas and oil indications.

Jan 3, 1925

By W. J. Kroll

Jan 1, 1960

By AIME AIME

THE best meeting ever held, was the opinion expressed by a number of those who attended the annual meeting of the Institute in New York, Feb. 18 to 21, and there was an atmosphere of friendliness and good fellowship about it that fully justified the feeling. In numbers it was not quite so large as last year and unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger, in respect to numbers, than that held in 1928, which was only made possible by the circumstance that the eighth floor of the building happened to be, temporarily vacant at the time. The number of rooms available for -sessions that were provided when the building was built long ago proved inadequate, and it is only by the expedient of obtaining the temporary use of the board and committee rooms of other societies that it is possible to arrange for the over 40 sessions that must be spread over the four days of the meeting. The-fifth floor, where. a buffet lunch is served each-day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size.

Jan 1, 1929

By T. A. Lang

For permanent structure underground, where rock is not competent, support usually consists of concrete or reinforced concrete. However, temporary supports in the form of timber or steel are often needed during construc-tion. Although the history of rock bolting is relatively short—50 years— their use has become widespread in general engineering construction as well as mining. This profusely illustrated and detailed study covers a broad range in the field of rock belting: from the behavior of rock and bolts including rock properties, masses, and structure; mathematical formulae for rock bolt applications; through analysis of various operations and descriptions of the bolts themselves. Rock construction is one of the oldest of the engineering arts and its origin is lost in antiquity. From the days when early man decided that he wanted to improve the natural caves which he was using for shelter and protection or made a river crossing by placing rocks to form a ford or causeway, we have had structures made of rock. It is not too much to say that rock in situ as a structural material forms part of every major engineering undertaking. Rock bolting is one means whereby the inherently good characteristics of rock in situ are preserved and used to the best advantage and the bad characteristics ameliorated. In many cases the latter are accentuated by construction processes used. Rock bolting, as with other rock construction techniques, is only just beginning to emerge from being an art. Consequently, its theory and practice is still more descriptive than mathematical. ROCK BOLTING In underground excavations, where the rock is not competent, support is provided. For the permanent structure, this generally consists of concrete or reinforced concrete. However, support may be needed during construction before the concrete can be placed, and conventionally this consists of timber or steel support in the form of ribs, struts, and lagging. Alternatively, rock bolts may be used. Although their use dates back over 50 years, it is only in recent years that rock bolts have become widely used, not only in mining but in general engineering construction. A rock bolt is a steel bar which is inserted in a hole drilled in rock. The end away from the rock face has a device which permits it to be firmly an- chored in the hole and the projecting end is fitted with a plate which bears against the rock surface. The bolt is placed in tension between the anchor and the plate, thereby exerting a compressive force on the rock. The essential feature of a rock bolt is that it is placed in tension. This distinguishes it from anchor bars which are grouted into holes in rock, but which are not prestressed. The difference between an anchor bar and a rock bolt when the rock bolt is grouted in is analogous to the difference between the reinforcement in ordinary reinforced concrete and in prestressed reinforced concrete. The view that rock bolts only pin or nail blocks or slabs of rock which are loose to the sounder rock behind them is erroneous. Rock bolts are useful for this purpose and have been so used for a long time. However, the term rock bolting, as used here, means the designed use of rock bolts to reinforce and develop the rock around an excavation into a structural entity which can competently play its part in a structure such as a powerhouse or a mine installation. Rock bolts behave quite differently than steel ribs. They can be installed at the working face directly after blasting and within a short space of time can be exerting a stabilizing pressure on the loosened rock surface. This early installation not only partially restores loosened blocks of rock to their original unloosened positions, but also it prevents the gradual relaxation or loosening of the decompression zone behind the new rock face. In contrast, steel ribs generally use timber blocks, wedges, and lagging between the ribs and the irregular rock surface. The timber is relatively compressible, and loosened blocks of rock must move outwards an appreciable distance before any load builds up on the steel ribs. Also, the ribs may settle as the foot blocks and foundation become compressed. Hence, it may take several days or weeks before the rock has moved sufficiently to make the steel ribs carry an effective load.

Jan 1, 1961

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943