Search Documents

By H. H. Pierce, J. B. Austin

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose. Ferrites and Marmatites The name "ferrite" has been given to the compound of zinc and iron which has the formula Zn0.Fe203. Among the questions pertinent to this subject are those involving inherent or natural ferrite, and also the synthetic or artificial variety. The inherent or natural product is formed when the mineral containing iron and zinc sulfides isomorphously crystallized is subjected to oxidation at roasting temperature. These isomorphously crystallized minerals are known, mineralogically, as marmatites, and contain ZnS and FeS in ratios of 2 to 1 up to 5 to 1 respectively. The zinc and iron sulfides form a definite mineral. They are firmly attached to each other and form common contact planes through which diffusion of the entities occurs during the roasting process. This diffusion of the molecularly intimate entities produces, during roasting, the compound referred to as ferrite, in proportion to the amount of iron originally present in the marmatite. For example, a marmatite from British Columbia containing 9.739 per cent. Fe and 56.87 per cent. Zn corresponds with the mineral having the formula 5ZnS.FeS. The ferrite produced in roasting, which has the formula ZnO.Fe203, contains 27.07 per cent. Zn and 46.40

Jan 1, 1929

THE Annual Fall Meeting held in Chicago in conjunction with the celebration of a Centennial of Engineering brought forth a round of field trips and symposiums which did much to add to the store of information of the 240 who registered for the gathering. Instead of a scattered program, technical papers were grouped together in organized symposiums, where the particular importance of each report was enhanced by presentation in context. Despite the heavy accent on technical papers and informative field trips, those attending the meeting had ample time to enjoy the benefits of a visit to Chicago. The AIME dinner dance was held at the Palmer House, in the Red Lacquer Room. The Chicago Section played host Friday evening at dinner. The MBD held four sessions at the meeting headquarters, the Palmer House, September 4 and 5. Featuring the meetings was a review of taconite concentration and new theories on comminution. The first session opened with a paper on the Structural Features Which Effect the Concentration of Iron Formations, presented by F. J. Tolonen. The paper was centered upon the various members of the low grade iron formations of the separate Michigan districts. The study correlated macrostructure, microstructure, and concentration tests. [ ] Beneficiation Characteristics of Michigan Low Grade Iron Ores, presented by F. X. Tartaron, cochairman of the session, reviewed the work of his laboratory on the beneficiation of low grade ore taken from various strata of a deep shaft on the Marquette Range. The paper included data on flotation, gravity separation, magnetic separation, and combinations of these processes. The economics of low grade ore treatment generated great interest. Ty. Maki offered a compilation and correlation of field results with magnetic separators in ferrosilicon and magnetite medium recovery circuits. Following the morning session, 130 persons attended a luncheon, followed by a brief business meeting. Later, a film illustrating the grinding, separation, and pelletizing steps investigated by the Mines Experiment Bureau, was presented by H. H. Wade. T. E. Ban, and L. J. Erck gave a report on pelletizing which evoked much discussion. R. A. Limons presented a paper on the Mineralogy of Blast Furnace Sinter, for its author, H. M. Kraner. Friday sessions featured a new hypothesis for high speed drill rod milling and a new technical approach to comminution. Jack Myers commented that Consolidated's large rod mill was a hammer mill turned inside out. Steve Erickson described the use of Cyclones for Heavy Media Concentration of Iron Ore Fines. Bob Meaders gave a Progress Report on the Aerofall Mill. Shiou-Chuan Sun described an improved high frequency analyzer for studying the conductivity of suspensions of various minerals. L. A. Roe discussed a magnetic reflux condensor which enabled him to determine the degree of liberation of magnetic iron ores. Roy A. Johnson described a function of the hydroscilator in which the fan rake was eliminated in favor of a conical bottom. The Industrial Minerals Division sessions held September 5 and 6 and were well attended. The Friday morning session was particularly concerned with developments and advances in industrial minerals with special emphasis on the Chicago area. The first two papers dealt with transportation on the Great Lakes and fuel movement into the Chicago area. The third paper proved to be of great interest, turning the spotlight on the fairly new hydraulic mining methods introduced by a silica company in the Ottawa, Ill. field.

Jan 1, 1952

By J. B. Murdoch, John G. Jackson

The many mechanical, geological, and economic factors which influence the planning of a directional drilling program are thoroughly discussed and analyzed. It is demonstrated that the planning of a directionally drilled multiple-well artificial island location is a complicated undertaking and that it is imperative that complete planning and engineering analysis be undertaken before the program is started. Complete planning is profitable because all of the factors influencing the directional work are in general interrelated and many time compromises have to be made before a harmonious program results. The engineering control necessary to accomplish a complicated directional drilling program is outlined. Various means by which engineering control can be increased, such as cylinder drilling specifications, are given. A hypothetical example is developed for a complete offshore artificial island of ten wells to demonstrate the more important factors involved in the planning. Included with this example are special charts and tables which make more rapid the drafting of directional drilling proposals and maps. Introduction A petroleum engineer must consider many and varied factors when planning a long range directional drilling program for an offshore or inaccessible location on an oil structure. The basic principles of direc- tional drilling planning and operation must be reconciled with his company's drilling practices, and frequently special concessions to standard drilling and production practices should be made. The field techniques and tools used in directional drilling are well known and widely used, but the deliberate, careful planning of a complete directional program is in the main a recent innovation. This development, plus the increased demand for oil resources and the consequent exploitation of inaccessible structures and offshore locations, has placed this problem before many engineering departments for the first time. Directional drilling programs of a very complex and difficult nature have been successfully carried out in the Mid-Continent and Pacific Coast regions. The planning itself of a directional drilling project, however, has not had the careful analysis it deserves and we can reasonably expect widespread future progress along thesc lines. Data and experience gained in these programs by the directional drilling service companies and the oil producers have been studied with the objective of giving the engineer a better conception of the factors which govern the various steps in planning a series of directional wells. The newest engineering procedures are the result of recent careful analysis of years of directional drilling work accomplished under the supervision of directional drilling service companies working with the oil companies. The purpose of this paper is to illustrate

Jan 1, 1949

By Thomas W. Dawson

The H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnages and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center to center of pulleys. It operated at a speed of 250 ft. 'per min-and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons was carried by the belt. whi1e: this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and, therefore, had to be crossed at each location to deliver coal to the river. After careful study, it was decided to transport this coal from the hoisting shaft to the river at each of these plants by belt conveyors.

Jan 1, 1925

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 1, 1950

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

By Lawrence H. Van Vlack, Otta K. Riegger

Periclase-type oxides were examined microscopically after being exposed to siliceous liquids. The rate of grain growth was found to be inversely proportional to the grain diameter. Grain growth proceeds more rapidly at higher temperatures, but is retarded by increasing liquid contents. aMag-nesiowiistites with higher MgO contents grow less rapidly than those with higher FeO contents. The growth rate is reduced by the presence of a second solid phase. The silica-containing liquid penetrates as a film between the individual magnesiowus tite grains. This is independent of time, temperature, amount of liquid, or the MgO/ Fe0 ratio. When present, olivine and spinel-type phases can provide a solid-to-solid &apos;&apos;bridge" between magnesioustite grains. THIS paper presents the results of a study of the microstructures of periclase type oxides in the presence of a silicate liquid. The purpose was to learn more about the effect of service factors such as 1) time, 2) temperature, and 3) liquid content upon A) grain growth, and B) liquid location among the solid grains. This study was prompted by the fact that periclase refractories are known to have very little solid-to-solid contact when the phases which are present are limited to periclase and liquid. Such a micro-structure gains industrial significance because it permits fracture during service when stresses are applied at high temperatures. The details of ceramic microstructures have not received extensive attention. This is in contrast to the extensive attention given to a) the phase relationships pertaining to refractory compositions, and b) the details of the microstructures of comparable metallic materials. A brief review will be made of the pertinent phase relationships and microstructural considerations in general, as well as of refractory compositions. a) Phase Relationships. This investigation was limited to those compositions in which (Mg, Fe)O was the solid phase. MgO and FeO form a complete series of solid solutions. Pure MgO has the name of periclase. The related FeO structure is called wustite. Both have the NaC1-type structure: however, wustite possesses a cation deficiency so that the true composition is Fe<10 even in the presence of metallic iron. The phase relationships involving solid (Mg, Fe)O and a silicate liquid are shown in Fig. 1. In this case. the liquid is saturated with (Mg, Fe)o. There-fore its SiOz content is below that encountered in orthosilicate liquids. As a consequence the liquid phase specie:; are primarily the following ions: and 0-&apos; plus occasional Fe+ ions. Two features are of importance: a) the liquid contains relatively small species and b) the liquid contains large quantities of the same species as the solid. viz., Fig. 2 shows the system, FeO-SiOz, which will be used in some of the discussions that follow. This diagram is the right side, vertical section of Fig. 1. Here, as pre\iously, the composition at the FeO end of the diagram is nonstoichiometric, varying from Feo.950 when the liquid oxide is in contact with the solid iron, to about Fe 0, when the solid oxide is in equilibrium with an atmosphere of equal proportions of CO and C02 at the solidus temperature. The Fe/O ratio will be maintained in wustite in the presence of SiO,. However, the FeM/Fe++ ratio in the liquid will be lower because of the effect OIF the SiO, on the activity of the FeO. With the addition of MgO to wustite, the over-all composition (IvZg, Fe)@, has a value of x lying between 0.9 and 1.0 when the COz/CO ratio is 1.0&apos;. b) Microstructures. In general, published attention to refractory microstructures has been directed toward the phase analyses that accompany compositional variations. This is illustrated by Harvey6 in his work on silica brick and by wells7 in his work on periclase brick. In each case, a series of altered zones is encountered which provides a sequence of phase associations. If due consideration is given to reaction kinetics, such an examination reveals phases that are compatible with equilibrium studies. Admittedly, however, it is often necessary to determine more complicated polycomponent systems to account for all the phases present.8 Relatively little attention has been given to microstructural geometry in ceramic materials. Certainly less attention has been given to this aspect of ceramic microstructures than to the size, shape, and distribution of the constituent phases in metals. Burke has pointed out that the grain size of oxides follows the same growth rules as for metals, viz.,

Jan 1, 1962

By Charles D. Walcott

The following acts of the Directors are reported for the information of members At a meeting held June 20, 1907, Dr. Charles D. Walcott, Director of the U. S. Geological Survey, Washington, D. C., having been recommended by unanimous vote of the Council, was unanimously elected an Honorary Member of the American Institute of Mining Engineers, in recognition of his personal services to American geology, and of his generous co-operation with this Institute, to the Transactions of which he has not only himself made valuable contributions, but has also encouraged the preparation of such contributions by the members of the U. S. Geological Survey under his charge, his liberal policy in this respect having gone so far as to permit the preliminary publication by the Institute of important results reached by the geologists of that Survey, even before their final and full publication as public documents. This wise and generous course has not only brought the U. S. Geological Survey into intimate and sympathetic relations with the mining industry of the world, but has also enriched the Transactions of the Institute, especially in the department of the science of ore-deposits, with many valuable papers. At a meeting held Jan. 14, 1908, Mr. Charles Kirchhoff was unanimously re-elected a Trustee of the United Engineering Society, to serve for a second term of three years. At a meeting held Feb. 18, 1908, directly after the adjournment of the annual meeting of the Institute, the following officers were elected for the ensuing year: President, James Gayley: Vice-President, James Douglas; Secretary, R. W. Raymond; Treasurer, Frank Lyman.

Mar 1, 1908

By C. R. Keyes

Discussion of the paper of C. R. Keyes, presented at the Chattanooga meeting, October, 190S, Bulletin No. 26, February, 1909, pp. 119 to 166. E. R. BUCKLEY, Flat River, Mo. (communication to the Secretary*) :-Some statements in the paper of Mr. Keyes relative to the nature and formation of the Ozark lead- and zinc-deposits seem to me erroneous and misleading, and I respectfully present the following criticisms, placing Mr. Keyes&apos;s original statements in quotations. Referring to the Ozark dome: (P. 127.) "It is a region that has been repeatedly upraised and planed off, until in the middle portion the oldest known&apos; rocks only are exposed." Does he mean that the St. Francois mountains, which have always been considered as lying on the eastern flank of the Ozark dome, are the middle of the dome? Or does he mean that the Cambrian rocks of the generally-accepted middle are the oldest known rocks ? Certainly not the latter, and if the former, his idea of the middle of the dome is not in accord with that of others who are familiar with the region. (P. 138.) " . . . the ore-deposits are definitely associated with, or localized by, geologic structures of some kind that .produce in effect basins in which&apos; the underground waters are impounded, or their flow retarded." This statement does not appear to be altogether consistent with the facts, since the ore- bodies of the Joplin district, as the rule, occur in those parts of the Mississippian formation which have a tendency to accel¬erate the flow of ground-water rather than retard it. I might name the open, breeciated ground near Joplin, Webb City, and Oronogo as especially noteworthy illustrations. The ore-bodies, everywhere, occur in positions where there must have been a free and copious circulation of dilute lead- and zinc-solutions in the presence of reducing constituents. The inequalities in the distribution of the ore-deposits are

Oct 1, 1909

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state&apos;s annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state&apos;s annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

A plan which has just been approved by President Wilson, by, the Secretary of the Navy, and the Naval Consulting Board, provides for the active cooperation of the Associated Advertising Clubs of the World with the 30,000 engineers who will soon undertake the task of making a card index survey of American industry, so that it may be prepared for national defense, if need comes. Herbert S. Houston, President of the Associated Clubs of the World comments on the plan. "Through the great power of advertising we expect-to arouse manufacturers, workingmen, businessmen, in fact the whole country, to the vital need of making industry the basic line of defense so that, if necessity arises, it can supply munitions quickly and abundantly. "This is not a war measure, but a peace measure. The militarist will support it and so will the pacifist, as well as the great body of Americans in between. So the slogan `national defense and international peace, has been adopted believing that the two causes will be best served by linking them together. "While the primary thing, of course, is service to the country, it is manifest that this work of the engineers will be of the greatest service to industry in times of peace. If industry is mobilized for defense, it will be placed on a basis of efficiency to meet the keen competition that will surely follow the present war." Howard E. Coffin, one of the leaders of the American automobile industry, in outlining the far-reaching plans of his committee, the Committee of Industrial Preparedness of the Naval Consulting Board, said: "At the outset I wish to emphasize the absolutely non-partisan nature of this work. I am not even familiar with the political affiliations of the great majority of the members of the Board or of my committee. In setting out to, mobilize the industrial resources of the United States, we are concerned only with the benefit to the nation, and to that end we have called into being an organization made up of the best technical and business brains of the country, and that organization will work along business lines with strictly business methods. I think it reasonable to say that this is a movement perhaps unique in the history of national governments, and one geared up to the highest standards of twentieth century efficiency. "It is vitally necessary that American industry be made aware of the part it must play in the national defense. Our whole conception of warfare has been changed almost overnight. Our military heads at Washington are largely, of course, graduates of the very best technical schools, have been taught the profession of fighting, and are masters of that profession. As members of the Naval Consulting Board, we are unable to tell these men how to do their work. But while these departmental heads have lived with military problems all their adult years, we on the other hand have slept and eaten and lived with the industrial problems of the country. The two questions are wholly distinct, and the masters of one cannot possibly be the masters of the other. We are confronted then with the necessity of interlocking these two vast elements of our national life into a great working organization for the national defense. It is that which we are about to do.

Jan 5, 1916

ARSENIC and orpiment are two mineral substances of a similar kind, and they are by nature pure, without admixture of other species. In regard to their apparent qualities we shall say that their composition is scorched, well-purified earth; and because of a certain subtlety and easy digestion they penetrate very easily into fused metals, indeed they act in such a way that they corrupt and convert almost into another nature any metal with which they find themselves. Orpiment and arsenic act in almost the same way as do tin and mercury. With these the fraudulent alchemists blanch copper, brass, and even lead to the whiteness of silver. According to the physicians they are in fourth part hot and dry. They are also corrosive because of certain powers; indeed, they are a most powerful poison to the life of all things. Arsenic is found in white and citrine colors. Orpiment seems to be a separate thing, although both are formed in the same ore and both are in lamellae or scales. These lamellae or folds are thinner than paper, in fact

Jan 1, 1942

By T. F. Witherbee

That the single charging-bell, properly proportioned, is a good all-around device for distributing material in a blast-furnace can scarcely be questioned; yet it is equally true that, in some cases, it has not given perfect satisfaction; as has been demonstrated by the substitution of double bells, at furnaces under the beat management—generally in cases where anthracite, either alone, or with a portion of coke, was used as fuel. The defect of the single bell seems to be that it does not permit, beyond very narrow limits, such changes in charging as may be required by the temporary conditioil of the furnace. Modern furnaces using Connellsville or other good coke and Lake Superior ores seem to be well served with a single bell. At least, up to a certain size, somewhere about 18 by 85 ft. to 19 by 90 feet, these furnaces make low-silicon pig-iron with about 1,800 lb. of fuel, or in some cases very much less. The following instances occur to me, in which other forms of charging-apparatus have been employed with advantage: 1. A charcoal-furnace, 61 ft. high, 11 ft. in diameter at bosh, and 8 ft. 2 in. at stock-line, with a rectangular crucible, 42 by

Jan 1, 1905

By F. N. Rhines

Despite the large amount of study which has been devoted to the subject our present knowledge of the copper-oxygen system remains incomplete and unsatisfactory .in many respects. This applies particularly to those regions in which solid metallic copper exists. The primary object of the present paper is the contribution of new information relative to the solid solubility of oxygen (or cuprous oxide) in copper at atmospheric pressure, together with certain observations in the low-pressure regions of the system. It seems appropriate also to present a brief summary of the outstanding previous work on the constitution of mixtures of copper with its lowest oxide in order. to show the relation between the new facts and the system as a whole. The earliest recorded investigations of the copper-oxygen system are those of M. S. Lucas(l) $ and of M. Chevillot(2) in 1819 and 1820. Lucas believed that liquid copper is capable of dissolving its oxide, but neither he nor Chevillot was able to furnish convincing proof of this property. It was not until 1866 that T. Graham(3) definitely established the existence of such a solubility. Nine years later W. Hampe(4) measured its extent and roughly outlined the copper-rich portion of the system. The first really precise examination of the constitutional relationship between copper and cuprous oxide, however, was that of E. Heyn(5) who in 1900 published a temperature-concentration diagram covering the range from 0 to 10 per cent of cuprous oxide at atmospheric pressure. Within these limits of composition cuprous oxide was found to dissolve in liquid copper, forming at 3.4 to 3.5 per cent a eutectic which melted at 1065" C. R. E. Slade and F. D. Farrow(6) extended these studies to mixtures of higher oxygen content. They discovered that between 20 and 95 per cent of cuprous oxide the metal and oxide form two liquid phases at a monotectic reaction of 1195" C. The span of the biliquidal region diminishes slightly

Jan 1, 1934

By R. J. Hopkins, L. B. Haney

On the basis of limited experimental work conducted at the Port Pirie smelter, it would appear that, by increasing the specific surface of sinter, and possibly that of coke as well, a marked increase in the rate and degree of sinter reduction in the furnace shaft can be achieved. Fusion-point tests have shown that this increased reduction means a much higher sinter fusion point and narrower plastic zone, while the more efficient utilization of coke in the furnace is inherent in the intensification of reduction by the provision of a more reactive sinter surface. Investigations aimed at increasing the ability to operate the blast furnace with a higher lead tenor of sinter reducing fuel cost proportionately, and at eliminating the loss in reduction potential in coke entering the furnace, as shown by the presence of appreciable proportions of CO in the top gases, are reported. Several lines for future investigations that could result in improved smelting methods are proposed. A SOMEWHAT informal presentation of ideas on lead blast-furnace smelting will be given in this paper. These ideas have been developed during observations of furnace behavior at Port Pirie and earlier at Mt. Isa, and have been guided by the results of laboratory experiments at Port Pirie. The authors do not intend to propound any particularly new theories, but present their ideas as a basis for discussion which may help toward a better understanding and improved control of blast-furnace operation. Performance variations of considerable magnitude occur from time to time at most lead blast-furnace plants. While Port Pirie is fortunate in having a very regular supply of high grade concentrates, it is no exception in this respect. Such irregularities are of considerable economic importance and they constitute a challenge to present-day metallurgists in their efforts to obtain an ever greater degree of control over furnace operation. In operating as Port Pirie does with a relatively high lead charge, it has been recognized for a long time that shaft conditions are ,of the greatest importance. A practical, or engineering, attack on the problem of accretions consisted of changes in furnace design, e.g., by widening the shaft to 10 ft above the bottom row of tuyeres, and by the provision of curved ends and vertical walls.&apos; That this attack has had a great measure of success is shown by the fact that barring down of these wide furnaces is rarely necessary, shaft conditions have greatly improved, and sensitivity to charge variations has been markedly reduced. These modifications, followed by some metallurgical changes (chiefly the incorporation of pig iron into the furnace charge in 1948), have brought furnace operation to a point where some variables which were previously masked can now be studied. Accordingly, over different periods of time during the last five years, such variables as could be given numerical values have been recorded and subjected to statistical examination. The objectives of this work were: 1—to reveal the true importance of the different variables and 2—to show the proportion of total furnace variation which is unexplained and therefore referable to causes not measured at present? e.g., shaft accretions, sinter structure, coke structure, and others. Statistical Study of Variables In this work factors relating to furnace speed and lead reduction have been examined: 1—slag com-

Jan 1, 1955