Search Documents

Allan Gibb, Mount Perry, Queensland, Australia (communication to the Secretary):—In drawing conclusions from his observations, Mr. Van Liew has apparently overlooked the reduction in weight that takes place in the content of the converter. The percentage-compositions of the matte, etc., are not directly comparable for determining the rate of elimination of the impurities; and, in the absence of exact weights (which in such an operation could not be obtained), it is necessary to determine the relation between the impurities and the copper with which they are combined at various stages, in order to get data that are comparable. Owing to a portion of the copper being removed in the slag, etc., the weight of copper in the converter is not a fixed quantity, but.it is sufficiently approximate to permit very reasonable comparison. The analytical data given by Mr. Van Liew, reduced to this basis (a ratio between the impurities and the copper with which they are combined), are shown in the table on page 958. From this table it will be evident that Mr. Van Liea's conclusions as to the source of heat at digerent stages are not quite correct. During the first 10 minutes, no iron is scorified, the heat being derived from the oxidation of the sulphur, of which 7 per cent. of the total is removed in this time. Prom

Jan 1, 1904

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By Gerhard Derge

THE orientation relationships resulting from allotropic transforma-tions and the formation of segregate structures in metals and alloys have been the subject of the eight earlier papers in this series1. A brief summary of orientation studies has also been given by Sachs2. A survey of these papers discloses that the factors that determine the orientation relationship of a precipitated phase to its parent solid solution, as Well as the outward form and appearance of the new phase, are not completely understood. It is now evident that crystallographically analogous systems, as a rule, exhibit the same type of Widmanstätten figure and orientation relations, so that useful information is not to be expected from examination of a new alloy involving lattice combinations of which the orientation relationships are already known. Therefore, the determina-tion of the relations existing between lattice types that have not already been studied seems to be the most promising mode of attack upon the problem; both of the systems reported in this paper represent new com-binations of lattice types.

Jan 1, 1937

By S. F. Ravitz, S. R. Zimmerely

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 10, 1950

By Lovell Lawrence

MAGNETITE deposits in the Eastern States have been mined uninterruptedly since pre-Revolutionary War days. The industry, thriving in normal times, was given impetus in all periods of tumult, and continued to advance and expand, until the Lake Superior ores came into production. A period of comparative quiet existed until increased freight rates, together with increased mining costs on Lake Region ores, permitted the magnetites again to compete. This, coupled with World War demands, created unpre¬cedented activity. Producing plants were at their peak, new mines were equipped and put in operation and the industry pushed production beyond the absorption point. Ore stocks were tremendous, internal competition severe, and a great increase in import of European ores brought the industry to a low ebb in 1923.

Jan 1, 1933

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a 3/4-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 clays. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 clays. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 1/2 -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood hacking is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots; and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 2.5 to 33 per cent of the ore. Addi-tional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department.

Jan 1, 1938

By James W. Guider

Of all the technology available to the iron blast furnace operator, raw materials preparation [(Fig. 1)] is by far the most important. Superior raw materials have been basic to the success of the Japanese steel industry, and they are just as essential to the American steel industry in winning its competitive battle against foreign government subsidized steel imports. Therefore, the mine operator and the ore beneficiation engineer must strive to produce the highest quality raw materials possible to meet the precise demands of the modem blast furnace and steel plant.

Jan 1, 1982

By Arcy A., J. G. Davis, D&apos Shock

Results of a pilot operation in the Carlsbad Basin are discussed. After hydrafracing between wells, a block of potash was removed by solution techniques. The distance between frac wells was about 200 ft, the thickness of potash mineralization, 5 ft. By proper manipulation, a feed of concentrate brine was obtained. The ex-periment showed that the thin-bedded potash could be removed by the solution techniques. The details of well construction, method of operation, and removal rates are discussed. Continental Oil Co.'s laboratory research on the fundamentals of potash solution mining has been expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well systems were studied in the field work. Discussion Background: The current paper discusses one field test in which potash was solution mined by a two-well system from a thin sylvinite zone. The potential economic value of solution mining evolves from (1) the use of drilled holes and solution techniques instead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths. Recent interest has been focused on potash' and other soluble minerals, such as trona. Solution extraction minerals, such as copper and uranium, are also worthy of important consideration. In addition, many of the techniques are directly applicable to the construction of horizontal underground storage carverns in salt. There are two general approaches to potash solution mining. The first is to mine on a single-well basis, in which the same well bore is used for both injection and production. This method is slow, and the areal extent may be quite limited in other than very thick ore zones. The second, and the preferred approach, is to mine on a multi-well basis in which the solvent is circulated between wells. This technique, if applied in a manner which allows the ore zone to be mined from the bottom upward, results in nearly all the solution taking place from the cavern roof. Salt removal rates, therefore, are very much higher than from a single-well system.l Wells can be interconnected into a multi-well pattern by several means. One is to join single-well caverns in the lower part of an ore zone. Another is to use the hydraulic fracturing techniques developed in the oil fields.' We preferred the fracture approach because of its potential for creating the greatest area of salt exposure. Test Site Description: The field tests were conducted in New Mexico's Carlsbad Basin, where the potash deposits are flat and uniform over reasonable distances. Here, 12 potash zones are present in the massive Salado Salt section. The specific target was the Third Ore Zone which is about 4 ft thick at our location and about 1150 ft deep. The test pattern was designed in the shape of an equilateral triangle with a fourth well located in the center, 200 ft from each of the vertex wells. This configuration allowed the ore zone to be hydraulically fractured from the center well with good assurance that the fracture would intersect the bore of at least one outside well. Several multi-well test patterns would be available if the fracture connected all wells. Well Completion: Surface casing was set in the top of the Salado Salt at 600 ft to shut off water flows from the surface sands, and the salt section was drilled and diamond-cored to a point below the Third Ore Zone. A drilling fluid made of diesel oil with a small amount of emulsified water was used to drill and core the salt. This fluid was highly successful in preventing enlargement of the drilled hole and in promoting good core recovery. The three outside wells were completed by setting 51/2-in. casing at the base of a streak of anhydrite about 20 ft above the ore zone. Pipe was set high so that the intersection point of the fracture could be detected even if the fracture migrated above the ore zone as it progressed outward from the center well. The center well itself was completed by cementing 51/2-in. casing through the Third Ore Zone. Cement bond logs run on the center well have shown excellent bonding. Fracturing Practice: A mechanical tool was used to cut a notch through the casing and into the salt at a point about 1 ft below the ore zone in the center well. The purpose of this notch was to fix the point of fracture entry into the salt. The fracturing was done with water at injection rtaes as high as 30 bbl per min. The salt parted at 1450 psi; and it required only 5 min for the fracture to reach the well which was 200 ft to the south. It took about 5 min more to reach the other two wells. Caliper surveys were run to locate the point of fracture entry in the three outside wells. The fracture appears to have drifted downward slightly, entering the outside wells at the top of a streak of carnallite 8 or 9 ft below the ore zone. A cross section of the wells selected for the multi-well test is shown in Fig. 1. The figure includes KC1 values based on core analysis and the trace of the fracture plane between the wells.

Jan 1, 1971

By Norman J. Sather

LOCATION AND HISTORY The Bunker Hill Mine is situated on the south side of the Coeur d’Alene River in Shoshone County of Northern Idaho near the City of Kellogg. Kellogg, the largest in the Coeur d’Alene District cities, is at an elevation of 2,300 feet and has a population of approximately 7,000 people. It can be reached by air, railway or highway. The history of the Bunker Hill Mine dates back to August 26, 1885, when Noah S . Kellogg found the outcrop of the Bunker Hill ore body on the hillside above the present town of Wardner, Idaho, in Milo Gulch. A small concentrator was erected in 1886. Before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d’Alene Lake. After ten years of production, an interest was purchased in the Tacoma Smelter at Tacoma, Washington, to which the entire output was shipped. In 1916 and 1917 a modern lead smelting plant and refinery was erected and in 1927 and 1928, a modern Electrolytic Zinc Reduction Plant was built and put into operation by the Sullivan Mining Company which was 50% owned and now totally owned by The Bunker Hill Company. GEOLOGY AND MINERALOGY The Bunker Hill ore bodies are found in gray and greenish gray quartzite and argillaceous quartzite of Precambrian age and are known as the Revett and St. Regis formations. Most of the ore bodies are found in the St. Regis formation.

Jan 1, 1970

By John B. Hastings

THE origin of the watery vapors of vulcanism has always been an object of interest and speculation to the seismologist, and as theories of the genetic origin of ore-deposits have of late years been pretty well narrowed down to the expiring forces of plutonic action, the same question has had a lively interest for mining engineers and geologists, as is well shown by the discussions of the subject in our Transactions. The important part taken by volcanic emanations in the origin of pegmatites and quartz-veins, described in my paper, Origin of Pegmatite,1 and their latent power to concentrate into useful deposits such scattered gold as occurs in the Hartsel granite, make a discussion of their derivation but a natural third and final step. It is conceded that enormous amounts of vapor accompany volcanism, though perhaps we are apt to forget that steam has 1,700 times the volume of water, besides which the column seen over Vesuvius and other volcanoes is greatly mixed with air; the immensity of such volumes compared with solids and liquids is shown by the experiment of Gautier, who, by heating dessicated granite to 100° C., evolved from it uses 20 times, and steam 90 times, its own volume. Dana appraised the average amount of water left in ordinary rocks as 2.5 per cent. T. M. Read estimated that the Mississippi river carries to the sea annually 150,000,000 tons of rock material. If these Mississippi sediments, as deposited, contained 20 per cent. of water, it would be 600,000,000 cu. ft., or 4,500,000,000 American gallons, annually. Allowing the vapor suspended over a volcanic cone to be mixed with 80 per cent. of air, this amount of water converted into steam would replenish anew, every 9 min., a column 15,000 ft. high, 2,000 ft. in diameter at the base, and 10,000 ft. at the top. Read's estimate is only half of the amount given in a more recent and probably correct one .2

Jan 5, 1908

By Charles Fettke

IN 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northeast of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and Lux. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J: Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey.

Jan 1, 1928

By George H. K. Schenck, Peter G. Donald

There is an accelerating acceptance of change by management of cement companies. Diversity of response is noticeable in efforts across the country to reverse the downward trend in profits that brought margins in 1966 to the lowest point in 20 years. New concepts are emerging among managers as they seek to increase the efficiency in use of the basic corporate resources of men, capital and technology. The shift towards computerized control of cement manufacturing is making new gains as is diversification of cement companies into allied fields such as production and sale of natural and light- weight aggregates, crushed stone and concrete products. Increased interest in special products such as white cement and further moves overseas are also significant. Perhaps the most dramatic event of recent years occurred in Washington at hearings before the Federal Trade Commission where cement producers split on whether there should be FTC guidelines that would prevent ownership of ready-mixed concrete producers by cement companies.

Jan 4, 1967

By Robert Glass Cleland

WALTER DOUGLAS succeeded his father, Dr. James Douglas, as president of Phelps Dodge in 1916. Before assuming office, the new president had been assayer at Bisbee, superintendent of the Copper Queen, general manager of all the Phelps Dodge mining interests, and altogether had spent a full quarter of a century in various phases of the company's business. Energetic and imaginative, experienced and courageous, he had need of all these qualities before he surrendered the direction of affairs into younger hands, fourteen years later. For the period of his administration was one of sudden ebb apd flow, flush production, drastic curtailment, quick recovery, and near-disaster. In 1917, soon after Walter Douglas became president, Phelps, Dodge & Co., Inc., which had been formed in 1908 as a holding company, went through an internal reorganization for the purpose of simplifying the structure and changing it from a holding company to an operating company. The Copper Queen Consolidated Mining Company, which had the necessary charter power and authority to carry on the business of any and all the subsidiary com-

Jan 1, 1952

NEARLY one hundred members of the Mining and Metallurgical Society of America and friends of Professor Peele met at dinner at the Aldine Club, New York, on the evening of April 26, to take part in the ceremonies attending the presentation of the Society's annual gold medal. This had been awarded to Professor Peele by the Society in recognition of his laborious and painstaking work as Editor-in-chief of the monu-mental "Mining Engi-neers' Handbook. Carl A. Meissner acted as toastmaster. W. Y. Westervelt, a student and lifelong asso-ciate of Professor Peele, then recounted some of his friend's early exploits, be-ginning with his mining adventures in the paternal cellar, whereby the neces-sity for adequate ventilation was indelibly impressed on his mind. Graduating from the Columbia School of Mines in 1883, Robert Peele for several years followed the typical mining career, as assayer and superinten-dentatan outlying Colorado mine; mill foreman and assistant superintendent of the Silver King, in Ari-zona; in charge of a mine at Fairplay, Colo.; and superintendent for the Ore-gon Gold Mines Co., at Cornucopia. At intervals during this experience, he spent parts of four years on two mineral investigations m in Peru, Bolivia, Colombia, and Dutch Guiana. He i was called to Columbia as Adjunct Professor of Mining in 1892, and became Professor in 1904. During his sabattical leave in 1903 he travelled around the world, r stopping at some of the most important mining cen-ters, and in 1910 he renewed his acquaintance with South Africa and South America.

Jan 6, 1923

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By Norman Lamont

The evaluation of certain reser-voir properties, such as porosity and fluid saturation, from electrical well surveys has been widely accepted in petroleum engineering. Various investigators have established relationships between these properties and certain parameters which affect the response of the electrical log. Among these are the resistivities of the mud, its filtrate, and its filter cake. In 1949, Patnode1 established a relationship between the resistivities of the mud and filtrate. The well logging service companies have contributed relationships for the mud-mud cake resistivities2,3 These have been valuable since it was the practice to measure only resistivity of mud at the well site. During the mid-1940's the industry began drilling wells with oil-emulsion drilling fluids. These were conventional aqueous muds with a dispersed oil phase. Since 1950, oil-emulsion muds have been used on an increasing number of wells each year. However, the practice of measuring only the resistivity of the mud at the well site has continued, and the mud filtrate and mud cake resistivities have been determined by the above-mentioned relationships. Service companies are now equipped to measure all three resistivities at the well site. An investigation was conducted on the resistivities of oil-emulsion muds, mud filtrates, and mud cakes to determine if these values conformed to the relationships for aqueous muds. TYPES OF MUDS Fifty-one oil-emulsion mud samples were prepared in the laboratory following a standard manual' published by a leading mud company. The diesel oil in the samples varied from 5 to 50 per cent, the majority of the samples being in the 10 per cent region. The basic aqueous mud types which were converted to oil-emulsion muds were commercial clay and bentonite muds, low pH and high pH, caustic-quebracho treated muds, and lime treated muds. The emulsions were stabilized by dispersed solids, lignins, lignosulfo-nates, sodium carboxymethyl cellulose, or sulfonated petrolatum. It is worthy of note that after a quiescent period of two weeks at room temperature all samples, regardless of emulsifying agent, remained stable. The make-up water for the muds was from the laboratory tap. Resistivities were varied by the addition of table salt to the water. A range of mud resistivities from 0.44 to 3.9 ohm-m was obtained in this way. Twenty-three field muds were tested. These covered the same range of mud types as did laboratory muds. Oil provinces of the Gulf Coast, South Texas, West Texas, Oklahoma, Montana, and Canada were represented. MUD TEST PROCEDURE Each mud was tested for density, viscosity, pH, and filter loss by standard testing techniques. The resistivity measurements were obtained with a Schlumberger EMT meter. This meter required small volumes of sample, e.g., 2 mm. Filtrate was obtained from a Standard Baroid fil-ter press at the end of a 30-minute test. The filter cake from the same test was used for cake resistivity measurements. Mud, filtrate, and cake samples were heated to 100" F in a constant temperature water bath prior to measurement of resistivities. RESULTS The relation between mud resistivity (Rm) and mud filtrate resistivity (Rmf) is shown in Fig. 1. The solid line represents an average for the data. The equation of this line is Rmf =0.876 (Rm) 1.075 . . (1) Arbitrary limits, indicated by the dashed curves, have been set. The majority of the data falls within these limits, but some points do lie outside the limits. The approximate equation Rmt = 0.88 Rm , . . . . (2) will give satisfactory results within these limits. The data on mud cake resistivity Rmc is shown in Fig. 2. The solid line is an average for the data. The equation for the line is Rmc = 1.306 (Rm)0.88 The dashed lines are arbitrary limits on the data. Within these limits, Eq. 3 may be simplified to Rmc = 1.31 Rm . . . . (4) DISCUSSION The limiting curves in Figs. 1 and 2 represent maximum deviations of ±25 per cent. Thus the use of the average curves can introduce considerable error. There is no substitute for accurate measurements of mud, mud cake, and mud filtrate resistivities at the well site. The mud sample tested should be representative of the mud opposite the formation being logged. The average mud filtrate resistivity curve of Fig. 1 is reproduced in Fig. 3 with two curves which have been published for clay-base aqueous muds2,3. The latter curves were determined from average values of a large number of drilling fluids. The three curves have essentially the same slope and the differences between them are from 7 to 22 per cent. Comparison is made only to illustrate the possibility of error

Jan 1, 1958

By A. F. Banks

INTRODUCTION Selective flocculation-flotation as a method of desliming potash flotation feed has been practiced in the Cominco Ltd. potash plant since November. 1974 when it was installed to replace a less efficient mechanical desliming process. The plant was designed for a consistent feed containing 4.5% insolubles. In practice the quantity and quality of the insoluble material is quite variable. This variability led to serious problems in the deslime circuit and consequently had an adverse effect on sylvite flotation performance. A costly mechanical solution to the problem was being seriously considered when it was drawn to our attention that a selective flocculation-flotation process had been developed. The process was tried first in the laboratory on the Cominco Ltd. ore, then on a pilot basis on 25% of the mill feed and finally full scale. The time from being informed of the process to full scale operation was 18 months. It has since been incorporated into a tailings regrind circuit. The original mine design called for the mining of an 11 foot height up to the top of the three clay seams. These had to be taken as they were a zone of structural weakness. It also assumed that the beds would be uniform with only a few disturbances. Very soon after the initial start up it was found that permanent openings had to take in the layers right up to the upper clay seams and because of the mining process that this material would have to be milled when encountered. The number of disturbed areas in the mine is greater than the design anticipated. In operation the insoluble content of the mill feed varies from 4.5% to 8% plus with the peaks being very short- term to relatively long, from hours to day. In terms of quality, the insolubles in the mining horizon are relatively soft and easily liberated, whereas those above are hard and liberate slowly.

Jan 1, 1979

CONTENTS PAGE BAIN, EDGAR C.-The Nature of Martensite. Discussed by Ancel St. John, Henry S. Rawdon, Jerome Alexander, Howard Scott 1 FEILD, ALEXANDER L.-Effect of Zirconium on Hot-rolling Properties of High-sulfur Steels and the Occurrence of Zirconium Sulfide. Discussed by Beram D. Saklatwalla, Bradley. Stoughton, Andrew M'Cance, George F. Comstock, Alexander L. Feild 12 SAUVEUR, ALBERT and KRIVOBOK, V. N.-Use of Sodium Picrate in Revealing Dendritic Segregation in Iron Alloys. Discussed by George F. Comstock, John H. Hall 17 KINNEY, C. L., JR.-Economic Significance of Metalloids in Basic Pig Iron in Basil Open-hearth Practice. Discussed by V. J. Pazzetti, George B. Waterhouse, C. L. Kinney, Jr 19 NEAD, J. H.-Absorption of Sulfur from Producer Gas in Open-hearth Furnaces.. Discussed by George B. Waterhouse, C. L. Kinney, Jr 26 PRIESTLY, WILLIAM J.-Effect on Steel of Variations in Rate of Cooling in Ingot Molds. Discussed by Emil Gathmann, Paul E. McKinney, George A. Dornin. 27 MONYPENNY, JOHN H. G.-Stainless Steel, with Particular Reference to the Milder Varieties (Stainless Iron). Discussed by P. A. E.-Armstrong, Beram D. Saklatwalla 33 ROYSTER, P. H., and JOSEPH, T. L.-Effect of Coke Combustibility on Stock Descent in Blast Furnaces. Discussed by Ralph H. Sweetser,. Richard Franchot, Sidney Cornell, T. L. Joseph 41 DAVIS, F. W., and BOLE, G. A.-Observations on Requirements of Refractories for Open Hearth. Discussed by C. L. Kinney, Jr., L. F. Reinartz, P. E. McKinney 46

Jan 5, 1924

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945