Search Documents

Discussion of the paper of J. E. Johnson, Jr., The Effect of High Carbon on the Quality of Charcoal-Iron, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 74, February, 1913, pp. 173 to °14, and of the paper of Albert Sauveur, Notes on Cast-Iron, presented at the New York meeting, February, 1013, and printed in Bulletin No. 75, March, 1913, pp. 503 to 524. CHAIRMAN. JOHN BIRKINBINE :-Just 20 years ago I had the pleasure, when I retired from the Presidency of the Institute, of introducing my successor, and this afternoon it is my pleasure to ask my good friend Dr. Howe to open this discussion. PROFESSOR HENRY M. HOWE, New York, N. Y. :-This paper of Mr. Sauveur's is extremely interesting. It is one of those papers that one wishes to read in the quiet of one's study, where it can be read with great profit. There are many points which he makes which I think are of very great value, in particular as to the importance of getting fine ;grained graphite by a relatively rapid cooling, combined with a high percentage of silicon. That theory would seem to be very promising; how far it has actually been carried out very likely Dr. Moldenke can. tell us.

Jan 5, 1913

By M. D. Cooper

FOr the purpose of obtaining some first-hand data in regard to the shooting clown of coal in bituminous 'nines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6,020 shots were fired by him during this period. All of the work was clone in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Co. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut.

Jan 1, 1917

By Albert Roberts

Summary In response to a growing intolerance towards ground vibrations and noise as environmental pollutants the engineer must consider the effects of his operations as they are likely to be judged subjectively by the public at large. Much work has been done on the study of vibration damage to structures, but the damage criteria normally applied do not take into account any resonance effects, nor do they embody any subjective criterion. Mu1tiple criterion techniques of subjective appraisal have proven to be of value .in the assessment of environmental comfort in relation to ventilation, air conditioning, and lighting. One such scale, the Reiher-Meister Scale, has also been applied to ground vibrations and noise, and an attempt has been made to correlate this scale with objective criteria, using the parameters of frequency and displacement. This paper quotes examples and compares ground vibrations resulting from blasting, the operation of, vibrating and impact-hamner pi1e drivers, forge hammers, and railway and road traffic. The Reiher- Meister Scale was applied to a subjective-objective correlation in relation to vibrations from railway traffic and gave results which did not conflict with experience.

Jan 1, 1971

By Benjamin C. Craft

Oil and gas development in Louisiana during 1935 brought this state at the close of the year up to fourth place in the nation as a producing area. A review of development in North Louisiana centers around Rodessa, the most important reserve discovered in this area in many years. While the producing limits have not been defined, this discovery is one of the major developments of the year. New gas fields were discovered in Lincoln, De Soto and Bossier parishes. The Lincoln Parish discovery, completed flowing a highly saturated gas from the Glen Rose, further indicates the importance of deep-seated prospects in the interior salt-dome area. Minor extensions were made at Sligo and Pine Island. During the year, 126 oil wells and 103 gas wells were completed in North Louisiana as compared with 144 oil wells and 68 gas wells during 1934. The North Louisiana oil production was 9,617,405 bbl. as com-pared with 9,274,050 bbl. during 1934, an increase of 343,355 bbl., while the gas production increased 18 billion cu. ft. in 1935 over its 1934 figure. The Louisiana Department of Conservation gage of Nov. 1, 1935, shows an open-flow capacity of 4,563,725,000 cu. ft. per day from 941 wells in the Monroe field and 682,770,000 cu. ft. from 159 wells in the Rich-land field. A great deal of leasing continues in North Louisiana as a result of the Lincoln Parish discovery and development in the Rodessa field, especially in Bossier, De Soto, Winn, Lincoln, Bienville, Webster, Ouachita and Richland parishes. South Louisiana's position as an area of important reserves was further proved during the past year. Increased drilling resulted in the discovery of seven new fields: Lafitte, Garden Island Bay, Tepetate, Bunkie, St. Martinsville, Jeanerette and Big Lake. New sands or producing horizons proved productive in 15 of the proven fields. The total oil production for South Louisiana during 1935 was 40,731,-056 bbl. as compared with 23,255,437 bbl. during 1934. There were 222 oil and gas wells completed in South Louisiana during 1935 as compared with 214 oil wells during the previous period. Drilling during

Jan 1, 1936

By R. S. Dean

THE first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselin1 in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228° C. In the next year, Stead2 placed the eutectic temperature at 247° C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time the present investigation was started. He concluded' that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247°C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if any-thing, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);" the thermoforce by Rudolfi (1910),12 and Pelabon (1923);13 the specific heat by Durrer

Jan 2, 1926

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By A. Hellawell

Specitlrens of the Al-Ge eutectic alloy have been frozen unidivectionally at rates between 2.5 x 10-6 and 2.5 x 10-4 cm per sec and the structure examined by optical and X-ray methods. There is no epitaxial relationship between phases, the aluminum having random orientation and the germanium a preferred (011) fiber textuve. Lamellar colonies which are BINARY eutectic alloys occur between either silicon or germanium with the metals aluminum or silver. common in this alloy are constructed from axial and nonaxial (111) plates of germanium which are related by a variety of twin configurations. Irregular or globular regions of the microstructure are composed of continuous single crystals of each phase, the germanium being heavily twinned. There is limited solid solubility in these systems, and the eutectic phases all involve diamond cubic with fcc crystal structures. In the microstructures of these eutectic mixtures the silicon and germanium crystals exhibit an almost infinite variety of shapes which are notably sensitive to

Jan 1, 1968

By J. K. Brooke, F. A. Renninger

During 1966, crushed stone production in the United States totaled just over 811 million tons valued at almost $1.2 billion. This represented in- creases of 4 % in tonnage and 5 % in value over that for 1965. Excluding the crushed stone used for agricultural and certain industrial purposes (cement, lime and flux), crushed stone mineral aggregate production totaled 616.3 million tons valued at almost $910 million, also up roughly 4% in tonnage and 5% in value over the 1965 figures. Limestone was by far the most widely used rock variety, followed by basalt, granite and sandstone in that order. Concrete aggregate and roadstone continued as the main uses for stone, accounting for 63% of all tonnage produced in 1966 and 60% of total stone value. Sand and gravel production in 1966 increased 3% over that for 1965. Total 1966 output was just in excess of 934 million tons valued at almost $985 million as compared with 908 million tons at $957 million for the previous year. Excluding the higher valued industrial sands, 903.2 million tons of sand and gravel valued at $891.6 million were used directly as mineral aggregates, representing a 2.9% increase in tonnage and a 2.4% increase in value over 1965.

Jan 2, 1968

By Clifford Wilson

SCREENED pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments a. Consolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use. of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1932

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By A. W. Hahn

USE of gold leaf goes back to biblical and even to prehistoric times. Both gold and silver, as well as other metals, were employed in illustrating or illuminating manuscripts. The medieval monks also used bronze powders. Metals were subdivided as finely as possible by mechanical methods, or by granulation and then were pounded into finely divided flakes. Substances such as honey have also been employed, since early times to keep the flakes of metal apart during grinding. Stearic acid is a more modern agent used in flaking aluminum and other metals. Finely divided "blue powder" is a by-product in retorting zinc ores, and contains from 78 to 90 per cent of zinc metal. This has been used as a precipitant for precious metals in the cyanide process and for chemical reduction processes. The making of zinc dust by atomizing is a step well known in electrolytic zinc plants. The Thermit process of Goldschmidt also requires the use of finely divided aluminum.

Jan 1, 1937

By John M. Bostwick

Bitumen is a general term for a group of materials composed of mixtures of hydrocarbons that are fusible and soluble in carbon disulfide. Included in the group are petroleum, asphalts, asphaltites, and mineral waxes. Asphalt is a dark-colored, cementitious solid or semisolid, which generally softens on heating and resumes a more viscous or solid state when cooled (personal communication). It is found in native form in fissures and pore spaces in rocks and as lakes. It is also obtained from the residues produced in petroleum refining. Asphaltites are black, naturally occurring solid bitumens. They are generally shiny and break with a conchoidal fracture. Common asphaltites are gilsonite (uintahite), grahamite, and glance pitch. Mineral waxes are solid or semisolid, relatively nonvolatile bitumens of various colors, having an unctuous feel and waxy luster. Of the native waxes, ozokerite is the best known. Montan wax is also classed as a natural wax, although it never occurs in the pure state and must be extracted from lignite or cannel coal (Ladoo, 1920). Mineral waxes may also be obtained by pyroprocessing of petroleum, lignite, and peat. Pyrobitumens are dark-colored, solid hydro- carbons that are infusible and relatively insoluble in carbon disulfide. They are so-called because they will yield liquid and gaseous hydrocarbons only when heated. Asphaltic pyrobitumens are defined as "substantially free of oxygenated bodies" and include wurtzilite (elaterite), albertite, and impsonite (Thrush, 1968). Nonasphaltic pyrobitumens contain oxygenated bodies; examples are coal and peat. The nonasphaltic type will not be discussed further. Petroleum Asphalts Asphalts refined from crude petroleum have almost completely replaced the native types. Refineries can produce asphalts in every desirable grade more economically and in greater quantity than the native types and with a variety of properties that meet the requirements of the various manufacturers using them. For all practical purposes, it is estimated that more than 95% of the asphalts consumed in the United States are refined from crude petroleum (private communication).

Jan 1, 1975

T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Mr. Killian is to be commended for his inquiry as to why a decrease of 15.3 pct in coke consumption was accompanied by a decrease of only 1.9 pct in the CO/CO, ratio of the top gas. Although I encouraged him in his efforts to find a more significant and meaningful carbon-gas ratio, the method, calculations, and conclusions originated entirely with the author. Whether we agree entirely with the assumptions underlying his corrected ratio, I think we can all agree that a better ratio is needed, and that he deserves credit for recognizing the need and for doing something about it. To be most useful, the CO/CO, ratio for the top gas should reflect the way in which the carbon is gasified in the furnace, particularly the degree of oxidation and the extent of heat release. The effect of CO, from the decomposition of the limestone and the effect of the reaction of CO and water vapor in the upper part of the furnace on the quality of top gas should be isolated from the effect of more basic reactions such as ore reduction and solution loss. The reduction of sufficient iron oxide to produce a ton of pig iron and the accompanying changes in the proportions of the carbon gases can be expressed on a mol basis as follows: 16.5FeA + 16.5CO - 33FeO + 16.5CO, [1] 33FeO + 33.0CO = 33Fe + 33CO. [2] The CO, from eq 1 normally escapes from the furnace because it does not react with coke at the temperature of its release. However, as much as 50 pct of the CO, from eq 2 may react with coke because it is released at temperatures above 1000°C: 16.5CO. + 16.5CO2 = 33CO [3] Thus we see that the gasification of 16.5 mols or about 200 lb of C in solution loss will regenerate as much CO as is required for the last stage of reduction. The pronounced effect of reaction 3 on the final proportions of CO and CO, in the gas stream is obvious. It also follows that reaction 3 materially alters the heat release but it cannot be entirely eliminated in Lake ore practice. A previous study indicates that 100 lb of solution loss may be necessary to maintain the reducing power of the gas. A reduction of 100 lb from the normal level of 200 lb would mean that over 1,-000,000 additional Btu are released in the process. The 100 lb of additional carbon which will be burned at the tuyeres will release 437,000 Btu and the absorption of 583,000 Btu by eq 3 would be prevented. One of the chief objectives of sized ore burdens and more uniform distribution of the gas stream is to minimize solution loss by completing reduction higher in the furnace and in turn to release the maximum amount of heat from the carbon charged. It was odd, indeed, to find that the use of sized ore and sinter in the careful tests reported by Dobscha had changed the CO/CO2 ratio very little. The author has stressed the close correlation between his corrected CO/CO, ratio and production. A correlation of fuel consumption and the CO/CO, might be more logical. Fuel consumption on the prepared ore burden decreased 15.3 pct whereas the corrected CO/CO2 ratio decreased 19.0 pct. Although this agreement between the reduction in fuel and the reduction in corrected CO/CO2 ratio is not as close as the correlation with tonnage, it indicates the corrected ratio is superior to the normal ratio which decreased less than 4 pct. Some adjustment should be made for the reaction: CO + H2O = CO2 + H2 —700Btu [41 because there is evidence to indicate that about one half of the hydrogen is formed in the upper 21 ft of

Jan 1, 1953

By J. L. Huiatt, D. G. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated methods of recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite and carnallite. Six sulfate- chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2% to 22.2% K20, and recoveries by crystallization ranged from 85% to 99%. Sylvite flotation from chloride evaporites with amine collector, recovered 90% to 97% of the potash in a concentrate containing 54.3% to 60.3% K20. Fatty acid flotation of the high sulfate evaporite recovered 78% of the sulfate minerals in a 28%-K20 concentrate. Flotation of the remaining chloride minerals with amine collector recovered 80% of the potash in a 59.7%-K20 concentrate. Solar evaporation of 37 854 L (10,000 gal.) of brine recovered 99% of the potash in a crude evaporite containing 24.5% schoenite and 20% sylvite. Flotation in a 45-kglh (100-lblh) continuous flotation unit recovered over 95% of the potash in schoenite and sylvite concentrates, containing 28% and 62.3% K20, respectively. An economic evaluation is included.

Jan 1, 1985

By R. M. Barnes, A. H. Bell

The ideas set forth in this paper are proposed for consideration and discussion as the result of recent study of various plans for control and proration of gas and oil production from Kettleman North Dome oil field. They would be applicable to any oil field during its flush production stage. The problems of development and proration are so Fig. 1.—Ideal Cross-section, Kettleman North Dome Oil Field. intimately connected in Kettleman Hills and in many other flush fields that they have both been covered in this paper. Many are of the opinion that Kettleman North Dome oil field should be considered as containing only one zone to its present total penetrated thickness of nearly 1500 ft., and that the hydrocarbon content of this zone gradually changes from dark and relatively low-gravity oil with relatively low gas-oil ratios on the flanks and plunges to mostly light-colored and high-gravity oil with high gas-oil ratios in the higher structural positions, somewhat according to the idealized section shown in Fig. 1. At least the lower 400 ft. contains dark oil in the higher structural positions.

Jan 1, 1933

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943