Search Documents

By H. L. Overton, J. B. Lipson

The concept of sodium single-ion equivalent activity as developed by Gondouin, Tixier and Simard,' was used to determine the filtrate resistivity-activity relationships for 150 laboratory and 49 field drilling muds. With the exception of the native and phosphate high-resistivity muds and the calcium-treated muds, the filtrate resistivity-activity relationships were found to be within 20 per cent of that for pure sodium-chloride solutions. Gondouin, et al,* previously suggested a method of treating the high-resistivity muds in quantitative electrical log analysis. A new treatment is presented which uses the P-alkalinity of the filtrate as a correlating parameter in handling the calcium-treated muds in quantitative electrical log analysis. INTRODUCTION Gondouin, Tixier, and Simard in 1957 introduced new interpretive procedures for analyzing the self-potential curve of electric logging. They re-emphasized the previous work of the Schlumberger brothers, Wyllie and others, and re-defined the activity concept in terms of a number which they termed the effective resistivity. Their procedures are particuarly effective when the connate-water resistivities are less than 0.08 ohm-m or greater than 0.3 ohm-m. For gyp muds where the calcium content is known, a procedure was presented which allows calculation of the connate-water resistivity with improved accuracy. These procedures assume that one of the fluids in the system is a pure sodium-chloride solution, but they are not limited by the assumptions. For the fresh and saline connate waters, for instance, it is assumed that the drilling mud filtrate is a pure sodium-chloride solution. For the gyp mud interpretive procedure, it is assumed that the connate water is a pure sodium-chloride solution. Brown,' on the other hand, has suggested that it would be extremely fortuitous if drilling mud filtrates could all be treated electrochemically as sodium-chloride solutions, and he cites some examples where discrepancies exist. A study has been made of the deviations of sodium single-ion equivalent activities, an of drilling mud filtrates from that of pure sodium-chloride solutions. Drilling fluids in common use on the Texas and Louisiana Gulf Coast and laboratory-controlled muds were investigated. Using a cell patterned after Gondouin, et al, (Fig. I), the equivalent activities were measured. It should be remembered here that the activity measured is merely an index which uses numbers that represent the sodium single-ion equivalent activity a,., of the mud filtrate. The membrane potential developed across the cell was determined with a null-type potentiometer. The resistivities of the solutions were measured by the four-electrode method. The resistivity system was calibrated by using saturated KC1 solution as a standard. Chemical properties of the drilling fluids studied were measured with standard API-approved equipment for the particular property in question. For the activity measurements, two shale discs were chosen to serve as cationic membranes. These two discs were both 1 1/4 in. in diameter and, respectively, 1/4 and 1/8 in. in thickness. The membrane potential, Em, was determined using the shale discs as cationic selective membranes separating two standard sodium-chloride solutions of known mean activity. Then by comparing the constant Km in the following equation, with the theoretical value of — 59 mv at 75OF, the perfection of the membrane was determined. The variation of Km for the two membranes used in this experimental work, as well as one of the many unsuitable membranes, is shown in Fig. 2. The measurement of the activity of mud filtrate involves the balancing of its combined individual activities against a standard solution of known mean activity. At the point where there exists zero potential across the membrane cell, the activity effects may be assumed equal for all practical purposes. The mechanics of making a null reading of this sort requires having a large number of different mean activity solutions. A more practical method involves

By R. C. Amero

FULLERS earth is a general name applied to claylike minerals that have high natural adsorptive powers. They are usually distinguished from ordinary clays by a higher content of combined moisture and a lower apparent density. The definition is based on the ancient use of the material for fulling, or cleansing woolen cloth of oil and grease; a more modern definition should mention the ability to decolorize oil and should differentiate between fullers earth, which is naturally active, and certain bentonites which only develop decolorizing power after being leached with strong mineral acids. The distinction between fullers earth and activable bentonite is not a sharp one, since all types of intermediate clays can be found that are more or less naturally active, yet more or less responsive to acid treatment. The differences seem to depend somewhat on the amount of leaching that has been effected by natural ground waters.

Jan 5, 1951

By Society of Mining Engineers of AIME

An error has been noticed in one of the figures in the 1974 Jackling Lecture "The Henderson Ore Body-Elements of Discovery, Reflections" by Stewart R. Wallace, published in SME Transactions, Vol. 256, No. 3, September 1974, pp. 216-227. The horizontal scale shown on Fig. 5 of this article is incorrect. The horizontal and vertical scales should be equal, i.e., the horizontal distance shown as 1000 ft should be 2000 ft.

Jan 1, 1976

By D. J. Carney, J. Chipman, N. J. Grant

G. Derge—With the development of this last weapon, there is not much of a chance for hydrogen. It is certainly a very interesting paper, and it gives us more confidence in sampling liquid steel for hydrogen than we have ever had before. This satisfactory work gives considerable confidence to all of the chilled methods of sampling which should be more or less successful depending upon the degree of chilling obtained. J. T. MacKenzie—How do you handle a nonmagnetic specimen in that device? D. J. Carney (authors' reply)—I left that out in going over the analytical procedure. For the 18-8 steel, what was done was to get some iron wire which was degassed. One turn of wire was made around the sample; it was inserted into the analytical apparatus, and that was enough to allow the magnet to pull the sample and drop it in the furnace. Other methods could be devised for this apparatus to do the same thing. This was just a quick method. C. E. Sims—This method of sampling and analysis is very ingenious, and the results obtained attest to a satisfactory degree of accuracy. It was noted in the paper that the samples are satisfactory only when there is a complete absence of pipe. This should be empha- sized, particularly in view of the fact that they are cut off under water. Some reservations are held in regard to the adequacy of the method of sample storage prior to analysis. Cooling on dry ice undoubtedly slows down the rate of diffusion to a marked degree, and it obviously suffices when the analysis is made within a few hours. All of the samples, except some of high-nickel steels, were analyzed within 12 hr. It is still unknown how long this method would be safe. In the work at Battelle Institute, it was impracticable always to start analysis within 12 hr for various reasons. Some samples did not reach the laboratory for several days, and some were held as long as a month before analysis. During this period, they were held over mercury, and the gas evolved at room temperature was collected and analyzed. It should be mentioned that both the mercury and the container must be kept very clean.

Jan 1, 1951

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

The vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.' These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The maior domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War 11, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1949

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower.

Jan 3, 1954

By Frank C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of trans- porting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion.

Jan 9, 1959

By Spencer R. Persik, Richard E. Munz

Measurements of many physical properties within an underground mine may be required as inputs to computer programs. These may be as simple as running/ not running signals from equipment, or they, may be representations of analog readings such as methane concentration. Similarly, outputs from computer pro- grams may control equipment located within the mine, as when air doors are opened or closed under computer control. This paper deals with the concept of electrical signal multiplexing and explains the role that multiplexing can play in comnunicating signals between the computer and locations within the mine. One multiplexer in particular, "DIRECTROL" (manufacturer by Cutler-Hamner Products), is examined in some detail, and its properties are discussed, including scan times, data security, recovery from cable failures, and recovery from power failures. Techniques of interfacing the multilexer to a computer are explained. Illustrations of the use of the multiplexer in mining applications are given.

Jan 1, 1983

By A. F. Crawley

The density and viscosity of 1iquid thallium have been measured by absolute methods to temperatures of about 200° and 150°C, respectively, above the melting point. These new data reported, especially density data, do not closely confirm previous work. Density p, in g per cu Cm, is shown to vary linearly with temperaluve t, in °C, according to the equation p = 11.658 - 1.439 X l0-3t. The viscosity data obey the well-known Andrade equation nv1/3 = A exp C/vT , the constants A and C for thallium having values of 2.19 x A and 79.648, respectively. This paper reports some new data for the density and viscosity .of liquid thallium. Measurements of these fundamental physical properties were undertaken as part of a continuing research program at the Mines Branch, Department of Energy, Mines and Resources, Ottawa. Canada. A literature search has revealed that data are so scarce that there could not be a consensus on the true values of the density and viscosity of liquid thallium. To be more specific, there exists only one set of viscosity data' and only two acceptable sets of density data,273 one of which is limited in scope.3 In Liquid Metals Handbook,3 another density study is reported but indications of impurities in the thallium render the results suspect. In this situation, further careful experimentation was required to realize the true density and viscosity of thallium. EXPERIMENTAL METHODS Density. Densities were determined using a graphite pycnometer. The technique and its accuracy have been discussed in earlier papers.4'5 It is considered that experimental data can be obtained which are accurate within +0.05 pct, all sources of random and systematic errors having been evaluated. Density results for thallium were identical whether measured under an atmosphere of argon or a vacuum of 5 x 10-6 torr and, for the most part, the argon atmosphere was used. Viscosity. Viscosity measurements were made in an oscillational viscosimeter by an absolute method—the liquid metal being held in a closed graphite cylinder. Design and operation of the apparatus, constructed in this laboratory, have previously been discussed.6 For thallium, runs were made under a vacuum of about 2 x 10-6 torr. To evaluate viscosity coefficients from the various experimental parameters, the mathematical analysis of Roscoe7 was used. Measurements of the necessary parameters and the accuracy of these measurements have also been discussed.6 The cylinder dimensions were corrected for the anisotropic expansion of graphite, as discussed for density measurements.4,5 It is well-known that thallium oxidizes rapidly and hence a newly machined surface quickly tarnishes in air. The oxide film, however. is nonadherent and is easily removed by rubbing or by solution in water. Hence, immediately before use, both density and viscosity charges were immersed in water, wiped dry, and quickly transferred to the apparatus which was then rapidly evacuated. Specimens removed after determinations were only slightly tarnished and there was no other evidence that tarnishing affected the results. For example, the sharpness of the specimen edges from the containing vessels indicated complete filling by the liquid metal. Thallium of 99.999 pct purity was used in this investigation. Because of its high toxicity care was exercised in handling this material. For example, the melting procedure to prepare machinable ingots was carried out in an open, well-ventilated area, while protective gloves were always worn when handling the solid metal. RESULTS AND DISCUSSION Density. Measurements were made over a tempera-ture range of about 200°C above the melting point. The results are listed in Table I and plotted in Fig. 1. From the graph it is evident that the relation between density and temperature is linear. Such a relation has been observed before in this program for other metals and alloys475 and elsewhere by other workers. A least-squares analysis of experimental data gives the equation: pT1 = 11.658 - 1.439 x 10-3t where p = density in g per cu cm and t = temperature in "C. In Fig. 1, together with the present results, the data of Schneider and Heymer2 in the corresponding temperature range have also been plotted. Evidently, the two sets of data do not agree well, the results of Schneider and Heymer being about 0.6 pct higher. Viscosity. Viscosity data were obtained from the melting point, 303.5°C, up to 457.5"C. The data are listed in Table I and in Fig. 2 the plot of these results demonstrates a smooth curvilinear relation between

Jan 1, 1969

By V. D. Leary, O&apos

Contracts between The Anaconda Co. and its miners at Butte, Mont., are not contracts in the true sense of the word. They are weekly verbal agreements which tacitly admit that the company, on the one hand, will supply the place, the tools, the material, and the opportunity and that the miners, on the other hand, will supply such effective labor that both parties will profit from the arrangement. Prices are seldom discussed at the time of hiring. The miner, in effect, is hired for a definite working place, as a contract miner, and if satisfied, tries to earn as much as he can. If he is not satisfied three courses are open to him: he can quit, he can ask for a change, or he can discuss prices or improved working conditions with the mine superintendent. This rather informal arrangement is due to conditions that are particular to Butte

Jan 2, 1961

By David H. Y. Tang, Syd S. Peng

In general, the strata sequence of the immediate roof in the under- ground coal mine openings can be divided into three types. They are: (A) each stratum deflects independently, (B) some stratum (or strata) loads on the underlying stratum, and (C) each stratum loads on its underlying stratum. The flexural behavior of the immediate roof which is made up of multiple strata not only depends on the material property, geometry, and external loading of rock strata, but also on the strata sequence. A computer program based on the beam-column theory is written for determining the bending stress and deflection for the generalized immediate roof. The flexural behavior of the immediate roof in various strata sequences are investigated for the following effects: roof span, horizontal stress, thickness and Young's modulus of the lowest stratum. In addition, some of the results are compared with the results of the finite element method.

Jan 1, 1983

By Jack L. Henry, R. D. Holliday

GASEOUS products of an aluminum reduction cell consist mainly of carbon dioxide and carbon monoxide. Sulfur dioxide, hydrogen fluoride, and hydrogen sulfide have also been conc~usively identified. Carbon tetrafluoride has been observed only during the period when the anode is polarized.' This period, known as anode effect, occurs when the alumina content of the molten bath approaches depletion.= Increased resistance at the polarized anode results in a voltage rise from a normal 5 volts to as

Jan 1, 1958

By John Fayerweather

Here is a challenge to industry to meet the need for management training for the men now passing from essentially technical work into managerial responsibility . . . And a program to handle the job. The purpose of this article is to throw out a challenge both to industry and to educators-a challenge to meet a crying need for management training among the young mining engineers of our nation, the men from 25 to 35 years old who are passing from essentially technical work into managerial responsibilities. It is the author's suggestion that these men could profit tremendously from the intensive training in management subjects which could be provided by short programs in mining administration. The challenge is to mining educators to provide such programs and to the mining industry to support the programs and to release their men to receive the training they need. Such a proposal clearly requires sound supporting arguments.

Oct 1, 1956

By Ezequiel Ordonez

MOST spectacular of Nature's contributions to the making of the postwar world is the Paricutin volcano, in Mexico, which I described in the July issue of this magazine last year, a few months after it was born. Now, after more than a year of continuous eruption, it is still and perhaps will remain a comparatively small though no less interesting volcano. The cone on April 1 had an altitude of nearly 1200 ft. above the level of the small flat field from which it began to grow on Feb. 20, 1943. This cone is now almost entirely surrounded by the lava flows that poured out at different dates, from its base or from outlets on the slopes near its base. To the north and northwest these lavas were

Jan 1, 1944

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

ALFRED C. LANE, Tufts College, Mass. (written discussion*).-The attention of members may well be called by Allen to his discoveries, which affect not only correlations in Michigan but, as I have pointed out,1 the use of names like "Animikie" which are widely applied. It shows that one disadvantage of the wide use of locality names is that local discoveries may show that they are inappropriate. The Wewe hills were found not to contain the Wewe slate! So we note that Allen, in his correlation, drops the term Animikie, which his researches indicate covers both middle and upper Huronian: It would seem well, then, in dividing the Huronian or Proterozoic, to use, as Allen does, terms like upper, middle, and lower Huronian, or newer, middle, and early, which may be shortened into eo-, mio-, and neo-Huronian rather than to carry local terms far away; or we shall soon be

Jan 12, 1919

By William E. Ford, Edward Salisbury Dana

In their action upon the senses a few minerals possess taste, and others under some circumstances give off odor. 444. Taste belongs only to soluble minerals. The different kinds of taste adopted for reference are as follows: 1. Astringent: the taste of vitriol. 2. Sweetish astringent: taste of alum. 3. Saline: taste of common salt. 4. Alkaline: tast'e of soda. 5. Cooling: taste of saltpeter. 6. Bitter: taste of Epsom salts. 7. Sour: taste of sulphuric acid.

Jan 1, 1922

H. 0. HOFMAN, Boston, Mass (written discussion*).-The paper by Mr.. Pyne gives clear evidence of the difficulties the metallurgist is likely to encounter when he tries to recover in the blast furnace the metal from old chromite lining used as a refractory material in the copper reverberatory furnace. It appears that chromite cannot be fluxed at temperatures which usually prevail in copper blast furnaces. This calls to mind the freezing-point curve drawn by M. Simonis1 of mixtures of chromite and kaolinite. The chromite used in the experiments contained 52.9 per cent. Cr203, 22.6 FeO, 4.8 AI203, 9.6 Si02, .10.1-MgO; FIG. 1. the kaolinite was clay from Zettlitz with 98.5 per cent. clay-substance: The accompanying curve shows that the eutectic mixture with 35 per cent. kaolinite and 65 per cent. chromite freezes at Seger cone No. 15 (1435° C.), while kaolinite fuses at cone No. 35 (1770° C.) and chromite at cone No. 42 (2000° C.). The curve indicates that the difficulty in the blast furnace can be overcome by having at the smelting zone a temperature much higher than is usual in copper smelting; a charge composition similar to that prevailing at the Mansfeld copper smeltery -which gives with 23 per cent. coke a, slag of the composition Si02, .49.09; .(FeMg)0, 5.58; (CaMg)0, 16.02; A1203,-16.02-might flux and fuse chromite.

Jan 3, 1918