Search Documents

By B. A. Rogers

ACCORDING to petrographic investigations, 1-4 cooled steel furnace slags contain a number of substances that have been shown to be ferro-magnetic5,6 and hence capable of undergoing appreciable changes of susceptibility with temperature. Since any alteration of the suscepti-bility of a constituent affects the average susceptibility of the sample, information concerning the nature of the substance should be deducible from its magnetic behavior. The possibility of obtaining information concerning slags in this way led to the construction of the apparatus to be described. FUNDAMENTAL PRINCIPLES OF APPARATUS The most convenient method of observing changes in mass suscepti-bility? with temperature is the one employed by Curie7 in his original investigation of the changes in magnetic properties of substances at elevated temperatures. As the method has been described frequently in the literature and in textbooks, only a brief review of the fundamental principles need be given here, but the particular arrangements used in the present work require a more detailed description.

Jan 1, 1939

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.' Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.' The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

By Harry W. Antes

The density changes that occurred on annealing cold-worked poly crystalline molybdenum, over the temperature range of 870" to 1630 SC, were determined. Increases in density were observed for recovery and the beginning of recrystallization. An initial decrease in density was observed during re-crystallization. A second decrease in density was observed after recrystallization was completed, as the microstructure changed from columnar grains to equiaxed gvains Both decreases in density were associated with an increase in gain boundary area to volume ratio. The second decrease in density was observed in the annealing range that immediately precedes secondary recrystallization as reported in the literature VARIOUS techniques have been used to identify the recovery, recrystallization, and grain growth processes that occur when cold-worked metals are annealed. As early as 1928 work was conducted that indicated measurable density changes occur when cold-worked single crystals of brass are annealed.' More recently, work by Murphy exhibited a corre- lation of density with microstructural changes observed on annealing cold-worked polycrystalline a brass.2 Other investigators have performed similar work on a brass and copper.324 In reviewing the literature, it was apparent that density work had been limited to fcc materials. Therefore, it was the purpose of this investigation to determine the density changes that accompany annealing the cold-worked bcc material, molybdenum. Two degrees of cold work, 30 and 90 pct reduction of cross-sectional area by rolling, were selected for this study. EXPERIMENTAL PROCEDURE High-purity vacuum arc-cast molybdenum was used in this study, the principal impurity being carbon in the amount of 80 ppm. The final rolling reductions were made at 1200°C in grooved rolls to provide 5/8-in.-diam rod. Density specimens 0.500 in. diam by 1.5 in. long were machined from the bar stock. The specimens were ground to the final dimensions to provide a smooth surface. Density measurements were made using a hydrostatic technique similar to that used by ~urphy.' This type of equipment permitted weighing in liquid immediately after the air weighing. During each weighing the temperature of the air and liquid was controlled to within 0.0l°C. This was accomplished by sealing the analytical balance in an air-tight brass chamber and surrounding it by an insulated wooden case. Preheated air was circulated in the air space between the brass chamber and wooden case by means of a blower. The temperature of the

Jan 1, 1964

By P. Greenfield, P. A. Beck

RECENT work by J. Darby, Jr. in this laboratory has shown that the reported vanadium-rich limit of the s phase in the Co-V system at 1200°C is in error. The appearance of a second phase in s actually is restricted to alloys containing over 68 atomic pct V. The error in the original value is due apparently to a reaction that takes place along the numerous cracks in the s specimens between the alloy and the impurities present in the He + 8 pct H atmosphere in the annealing furnace. Such a reaction and the consequent appearance of a second phase can be suppressed if the alloys are sealed under vacuum in Vycor tubing. The new value of 68 atomic pct V for the vana-dium-rich limit of the s phase in the Co-V system effects slightly the s compositions calculated from average values of N, and N,. for various s phases. The standard deviation between experimental mean compositions and those calculated from the assumption that s is characterized by a constant number of 3d + 4s electrons per atom (N,), is slightly reduced from 9.1 to 8.8 pct. The maximum divergence for the V-Mn s phase is reduced from 15.5 to 14 atomic pct. The standard deviation calculated from constant electron vacancy numbers given by N.. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2(Fe) + 1.71(Co) + 1.6(Ni) is now greatly reduced, as the maximum divergence for this correlation previously occurred in the V-Co system. This maximum divergence is reduced from 7.6 to 2.3 pct, and the standard deviation for all s- phases is reduced from 4.1 to only 2.9 pct. The correlation for electron vacancy numbers given by N. 5.66 (V when with Ni or Co) + 4.88 (V when with Mn or Fe) + 4.66 (Cr + Mn) + 3.3 (Mn) + 2.66 (Fe) + 1.71 (Co) + 0.61 (Ni) is made slightly worse, and the standard deviation increases from 2.8 to 3.9 pct. These changes, however, do not affect the conclusions of the paper.' The deviation between calculated and experimental s compositions is much less for either one of the electron vacancy correlations than for the correlation with the number of 3d + 4s electrons.

Jan 1, 1955

By C. J. Guntner, R. P. Reed

A commercial 18Cr-8Ni iron alloy (AISI 304L) was examined in tension at 300°, 76°, 20°, and 4°K. Continuous stress-strain recordings were made, X-ray analyses at periodic stress (strain) intervals were obtained, and the magnetic measurements were taken. From this data the percentage of martensitic products [bcc(a) and hcp (E)] was computed as a function of stress (strain). It was found thatup to 15 pct E phase forms at low temperntures. The amount of E formed increases to a maximum at about 5 pct strain, then decreases. This decrease indicates the additional transformation of E to a'. The total amount of E and a' was suppressed at constant stress (strain) at 4°K as compared to 76°K. It is proposed that the suppression of E and a' is associated with the decreased mobility of extended dislocations at very low temperatures. The yield strength decreased as the temperature was depressed below room temperature and then increased rapidly near 4°K. SOME ferrous alloys which are austenitic (fcc ?) at room temperature appear to be unique in that two martensitic products (hcp e and bcc a') may form on cooling to lower temperatures or on application of mechanical stress. The most common room-temperature austenitic ferrous alloys are 18Cr, 8Ni stainless steels. Most aspects of the spontaneous transformations have been previously described for these steels.' Several previous papers have described special aspects of the stress-induced transformations at low temperatures for the stainless steels, such as the existence of the hcp phase (c) after straining at 76oK,2-7 the morphology after straining using electron microscopy,7 and the decrease in E at higher strains at 76oK.4 However, for a complete representation, one must know the stress-strain characteristics and the dependence of both martensitic products on applied stress and temperature. It is the intention of this paper to provide that documentation. To accomplish this, continuous stress vs strain recordings were made at four temperatures: 300°, 76", 20°, and 4°K for annealed AISI 304L (a commercial 18Cr-8Ni alloy). At periodic stress intervals at each temperature the integrated X-ray line intensity of a selected peak for each phase (y, E, and a') was measured. In addition, photomicrographs of the strained surfaces were taken and magnetic measurements were made. The magnetic readings can be directly converted into percent a'.',e With these measurements the percentage of each phase may be plotted as a function of stress (or strain) and test temperature. It was found that up to 15 pct E phase forms upon stressing the AISI 304L alloy at low temperatures. The E percentage increases abruptly after the alloy yields, but then decreases gradually at higher stresses. The rapid increase in e at 76°K is associated with an "easy-glide" portion of the stress-strain curve. The total amount of a' + .G is suppressed below 76°K at a constant stress or strain. The yield strength decreases down to 76°K but increases rapidly below 20°K. EXPERIMENTAL PROCEDURE Tensile test specimens were cut parallel to the rolling direction from 0.1-in.-thick sheet. Continuous stress vs strain recordings were obtained at each test temperature (300°, 76o, 20°, and 4°K) using equipment and methods described elsewhere.' The specimens which were used in the X-ray analysis were stressed to successive increments of strain at each temperature, analyzed at room temperature, then restressed at the test temperature. This procedure was repeated until approximately ten X-ray analyses had been performed with approximately 1.0 pct strain increments. The specimens had a reduced section 1 in. long, 1.2 in. wide, and 0.1 in. thick. They were electro polished prior to testing and after each strain increment. Table I lists the chemical composition, grain size, and hardness for the alloy which was used. This is the same alloy for which extensive mechanical-property tests3 and morphological studies of the spontaneous transformations' have previously been made. For the low-temperature tests (76o and 4°K) below the Ms temperature the specimens were initially cooled to the test temperature, held for 1/2 hr, then warmed and X-rayed at room temperature. The results are listed in Table 11. From earlier work8 it was known that additional transformation on the second cycle would be considerably less (-0.1 pct

Jan 1, 1964

By George Rupp

THE Sunrise iron mine of The Colorado Fuel and Iron Corporation is in Platte County, Wyoming, about 110 miles north of Cheyenne. It is served by the company-owned Colorado and Wyoming Railway, which connects with the Chicago, Burlington and Quincy and the Colorado and Southern railways at Guernsey, Wyoming, a distance of 6 miles from the mine. The original Sunrise claims were staked mainly by United States Army officers and soldiers stationed at old Fort Laramie, because of small showings of copper in the Carboniferous limestones that form a horizontal capping overlying the Huronian iron ore. A small copper smelter was operated for about three years at Fairbanks, now an aban-doned town on the North Platte River. As many of the copper shafts and test pits near the present Sunrise mine were deepened, they pene-trated the capping and encountered iron. ore or gray sericitic schist, and were abandoned. Evidence of an early interest in iron ore was found when the Chicago claim was stripped for mining. A narrow, winding crevice was dis-covered, which led downward 20 ft. through the capping to the underlying soft red hematite, in which a room 10 by 14 by 7 ft. had been excavated. Stone hammers and wedges and a few rusted pieces of iron were found on the floor, and the evidence is conclusive that the excavation was used up to rather recent times by Sioux Indian medicine men, to provide war paint.

Jan 1, 1939

By B. K. Parekh, W. M. Goldberger

Silicon carbide (Sic), produced by heating rice hulls to elevated temperatures, contains a mixture of beta crystalline silicon carbide whiskers, particles, and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 microns in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean, high grade SiC whisker product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90%. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1986

By R. Taggart, G. R. Purdy

DURING a study of the tempering of ß-quenched alloys of cobalt in titanium, parallel lines were observed crossing certain faces of retained-ß crystals in the early stages of tempering, Fig. 1. The lines closely resemble stress-induced martensite' or substructures attributed to clusters of faults in titanium-nickel2 and copper-silicon3 alloys. The markings were observed only in intensely etched quenched and tempered alloys having compositions ranging from 4.5 pct* Co (the composi- formed by the lines was reproduced upon repolishing and reetching. Close metallographic examination indicated that the markings were troughs, Fig. 2, and that the characteristic surface substructure persisted within the troughs. The occurrence of the troughs was associated with the age hardening reaction due to the metastable u) phase (previously reported in titanium-cobalt alloys by Raub and Beeskow4 and indicated in this work by the broadening of 0 diffraction peaks and by hardnesses approaching 600 Dph). The troughs

Jan 1, 1961

By John Henry Harden

THIS shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & Wilkes¬Barre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51' 1/2" long, 17' 4" wide, 31' deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45' 4" long, 11' 16" wide, 31' deep, divided into six parts by buttons 8" x 12", each division, 7' x 11’ 16". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10"; backing, 3" thick ; clay puddle to ex¬clude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal ; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the" standard diamond" car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet.* Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pres¬sure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams. * Size of the "standard diamond" car, 8' 10” x 4' 3" x 2’ 8” = 100.1.4; loaded 4 inches above the top, 8' 10” x 4’ 3” x 3’ “0"= 112.7.6.

Jan 1, 1877

By T. Egleston

The importance of making analyses of gases in furnaces which are used for metallurgical purposes is every day growing more and more evident. It is the only method of understanding the reactions that take place in the furnace, and of economically conducting the operations both with regard to the fuel used and the reactions which take place on the bodies to be subjected to the influence of the heat and gases. As a knowledge of the composition of gases is becoming every day more necessary to the proper conduct of furnace operations, it seems desirable that furnace managers should generally know that the analysis of gas for commercial purposes is neither difficult, tedious, or expensive, and that it does not necessarily imply the use of corrections requiring difficult instrumental observations and long and tedious mathematical calculations. Any method, therefore, which will tend to render these analyses simple will also tend to having them made and repeated as frequently as the analyses of the ores and other materials charged in the furnace. They should be made even more frequently, as their composition is affected by any change in the condition of the furnace, and a knowledge of their composition will give a ready clue to the unseen and otherwise not easily detected changes which are taking place. The only practicable method of making industrial analyses of gas is that of measuring volumes in graduated tubes. The methods by

By T. PH. D. Egleston

THE importance of making analyses of gases in furnaces which are used for metallurgical purposes is every day growing more and more evident. It is the only method of understanding the reactions that take place in the furnace, and of economically conducting the operations both with regard to the fuel used and the reactions which take place on the bodies to be subjected to the influence of the heat and gases. As a knowledge of the composition of gases is becoming every day more necessary to the proper conduct of furnace operations, it seems desirable that furnace managers should generally know that the analysis of gas for commercial purposes is neither difficult, tedious, or expensive, and that it does not necessarily imply the use of corrections requiring difficult instrumental observations and long and tedious mathematical calculations. Any method, therefore, which will tend to render these analyses simple will also tend to having them made and repeated as frequently as the analyses of the ores and other materials charged in the furnace. They should be made even more frequently, as their composition is affected by any change in the condition of the furnace, and a knowledge of their composition will give a ready clue to the unseen and otherwise not easily detected changes which are taking place. The only practicable method of making industrial analyses of gas is that of measuring volumes in graduated tubes. The methods by

Jan 1, 1877

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

By D. Y. F. Lai, R. J. Borg

Tracer diffusion of Fe59 has been measured in the a-stabilized Fe-1.8 at. pet V alloy from 700° to 1500°C. The activation energies are obtained in both the presence and absence of magnetic order. Furthermore, it is established that diffusion in the alloy is identical to that in pure iron and consequently the values of Do and Q accurately represent the temperature dependence for self-diffusion. The purpose of this investigation is to obtain an accurate estimate of the temperature dependence for self-diffusion in bee iron in both the presence and absence of magnetic order, and, in so doing, to establish the temperature range of the magnetic effect.&apos;" As the temperature interval suitable for diffusion measurements is severely limited in both bee phases of pure iron because of the intervening fee ? phase, the experiments were performed on an a-stabilized alloy containing 1.8 at. pet V. This alloy is bee over the entire range from room temperature to the melting point. Although there have been several independent investigations of self-diffusion of iron in a, iron,1, 3-6 there still exists considerable disagreement regarding the values of Do and Q for the paramagnetic region. The two systematic studies of diffusion in 6 iron6, 7 previously reported are also only in fair agreement; but in view of the extremely small temperature range available for diffusion studies, i.e., 1390o to 1535oC, this is not surprising. It is comparatively easy to obtain accurate values of Do and Q for the a-stabilized alloy inasmuch as measurements can be made over the entire temperature range -700o to 1500°C. However, in order to assume that these same values apply to pure iron requires careful comparison of the data in the a, and 6 regions in both the alloy and pure iron. We have made several measurements in the appropriate temperature ranges and are unable to establish any systematic difference between the diffusion coefficients of iron in pure iron and in the alloy. We therefore conclude that the values obtained for the alloy are truly applicable to pure iron; the complete evidence favoring this conclusion will be discussed later in this paper. EXPERIMENTAL The experimental methods will be given here only in barest detail since they have been thoroughly de- scribed elsewhere.l, 7 The alloy was prepared by induction melting and chill casting under argon. Diffusion samples were machined from the ingot and annealed in hydrogen for several days at 900°C to give an average grain diameter of 1 to 2 mm. The penetration profiles of the tracer were established by a sectioning technique, the residual activity being counted after the removal of each section. The tracer used is Fe59 which emits two high-energy ? rays of 1.098 and 1.289 Mev, respectively; these were detected by a ? scintillation counter equipped with a pulse-height analyzer. For the measurements in the temperature range -700o to 1130°C the samples were vapor-plated with Fe59, encapsulated in quartz under vacuo, and annealed in resistance-heated furnaces which are controlled to ±1°C. The specimens diffused at higher temperatures are prepared as edge-welded couples, the two halves being separated by a thin washer of the alloy to prevent sintering. The diffusion anneal is then carried out by inductive heating under a dynamic vacuum. The temperature is monitored pyrometrically. RESULTS The diffusion coefficients are obtained from the penetration profiles in the usual way using the error-function complement relationship. The results over the entire temperature range are shown in Fig. 1. In the linear region, 900o < t > 1500°C the least mean squares (lms) values of the diffusion coefficients are given by D = 1.39 exp[-(56.5 ± 1) x 103/Rt] cm2/sec [l] The average departure of the measured diffusion coefficients from the values given by Eq. [1]In order to determine whether or not the slope is truly constant over the entire range from 900" to 1500°C, the data are arbitrarily divided into two groups, the first containing values between -900" and 1133°C and the second between -1133o and 1500°C. The lms values for the two groups are given by Eqs. [2] and [3]: D = 0.519 exp[-55.7 x 103 /RT](900° to 1133°C) cm2/sec [2] D = 1.45 exp[-56.7x103/RT] (1133° to 1500=C) cm2/sec [3] Thus, there is no significant difference between the high- and low-temperature segments of the linear region. This not only assures us of the consistency of the values obtained by induction heating as compared to those obtained from the resistance-heated

Jan 1, 1965

NEW MEMBERS The following list comprises the names of those persons who became members during the month of December, 1913: Members ADAMS, CHARLES W., JR., Smelting, American Smelting & Refining Co., Murray, Utah. ARMSTRONG, FRANK H., Mechanical Engineer Vulcan, Mich. ARNOLD, JOHN B., Attorney-at-Law Room 840,200 5th Ave., New York, N. Y. BOYS, HARRY R., Mining Paso Robles, Cal. CAVANAGH, JOHN L., Min. Engr., Nova Scotia Steel & Coal Co.; Wabana, Newfoundland. CHOW, KAI CHI, Student 1120 Amsterdam Ave., New York, N. Y. CLARK, ARTHUR B., Mining Engineer 72 Harbour Bldg., Butte, Mont. CURLEY, JOHN R., State Mine Inspector P. 0. Box 633, Leadville, Colo. DAVIS, ANGUS W., Mining Engineer, Consolidated Mining & Smelting Company of Canada, Trail, B. C., Canada.

Jan 1, 1914

By V. B. Kurfman

The temperature, strain rate, and orientation deDendence of defbrnzation of single-crystal MgAg has been examined. The crystals exhibit a tendency to single glide and little or no hardening at 25°C for many orientations. A much higher hardening rate is observed when multiple glide occurs, such as can be initiated by surface defects. The tendency for easy glide becomes less dependent on surface preparation and orientation as T — 100°C and bars so tested often fail after one-dimensional necking-. At T > 200°C (transition temperature for single-crystal notch sensitivity and poly crystalline ductility) single glide diminishes and two-dirnensionul necking begins. The crystals do not strictly obey a critical resolved shear stress law, but show the influence of {loo) cracks in determining the slip mode. The results are correlated with the difficulty of sciperdzslocation intersection and semibrittle behavior of this compound in single-crystal and poly crystalline form. Comparisons are made with the slip selection mode observed in tungsten, with the reported observations of easy glide in bee metals. and with the mechanical behavior of poly crystalline MgAg. PREVIOUS work on tensile deformation of polycrys-talline MgAgl and bending deformation of single-crystal MgAg2 has shown that the compound is semi-brittle (i.e., notch and grain boundary brittle). If this semibrittleness is supposed to result from the difficulty of multiple glide (associated with the problems of superdislocation intersection) one might expect single crystals deformed in tension to show pronounced single glide and strong orientation dependence of hardening rate. These experiments were done to examine this supposition and to study the tensile deformation of a highly ordered system which may be considered bcc if the difference between the two kinds of atoms is ignored (actual structure: CsC1). EXPERIMENTAL Single-crystal ingots were grown by directional freezing as previously described.&apos; These ingots were sliced into a by a by 2 in, rectangular bars by electric discharge machining, then round tensile bars were conventionally machined to 1/8-in.-diam by 1-in.-long reduced section. The bars were typically tested without an anneal because of the problem of magnesium vapor loss and they were typically tested as mechanically polished. The analyses are within the same limits as those reported earlier; i.e., the average composition for each specimen is within 0.5 at. pct of stoichiometry, while the total range from end to end in a given specimen varies from 0.7 to 1.4 at, pct. There has been no indication in the results of any variation in slip or fracture mode attributable to the composition fluctuations. The slip systems were determined by two-surface analysis of the bars after testing to failure at room temperature. Single glide was so dominant that there was little difficulty in identification of the dominant slip system even though the tensile elongation to failure often approached 7 to 8 pct in room-tempera- ture tests. Elevated-temperature testing was done in a silicone oil bath and low-temperature testing was done in liquid Np or a dry-ice bath. All stress measurements are reported as engineering stress unless otherwise specified, and crosshead travel is used as the strain measurement. RESULTS The tendency toward single glide is best seen in the pictures, Figs. 1, 2, and 3, which depict deformation at fracture as a function of test temperature. While it is possible to find regions of secondary slip by careful microscopy, such regions are very small. The development of a ribbon-shaped configuration from an initially round section bar pulled at 100°C is typical, occurred by single glide, and illustrates the degree to which such glide continues. At temperatures =100°C the bars typically show elongation of 20 to 50 pct by predominently single glide. Despite the large elongation, fracture even at 150°C occurs in a brittle mode, Fig. 2, in the sense that it is an abrupt failure which shows no discernible necking in the second dimension of the bar&apos;s cross section (i.e., there is no appreciable action of any slip modes which would decrease the broad dimension of the cross section). Near 200°C the fracture mode changes slightly. Although most of the sample extension is by single glide, after the bar develops the characteristic ribbon shape it begins to neck in the second (i.e., broad) cross-sectional dimension. The bar becomes very thin in the "necked down" region, Fig. 3, and the reduction in area approaches 100 pct. Often there oc-

Jan 1, 1967

By Charles White Merrill

Money is one of the most .pervasive elements in human life. The compensation for a workman&apos;s daily efforts is expressed as a wage and is measured in money. What an individual may consume depends largely on his income which also is expressed in terms of money. If he would start an enterprise its size would be determined in large part by the amount of money available for capitalization and its success would be measured in net income expressed in money. In short, the most widely used common denominator for comparing merchandise, real property, jobs, enterprises, gross national product, or personal success is money. Despite this use of money by almost everyone past infancy to express his appraisal of the in- numerable values he sees around himself, the complexity of the device called money makes its nature and workings a mystery to most users. Some of the difficulty in understanding money results from the fact that it has three distinct but interrelated functions: (1) a medium of exchange, (2) a unit of account, and (3) a store of value. In many statements about money the discussion moves from one function of money to another without the speaker or the listener recognizing the changes. For example, the housewife says "We took the money we had saved up to make the down payment and after twelve monthly payments the television will be ours." When this housewife spoke of "saving up the down payment" she referred to money in its function as a store of value; when she spoke of "the down payment" she was using money as a medium of exchange; and when she referred to the "monthly payments" she spoke of money as a unit of account. Another cause of confusion in understanding money is its paradoxical nature in that it represents both the power to produce and the power to consume. For example, when the rich uncle dies one nephew may regard his inheritance as an opportunity to buy a farm and leave the ranks of the wage earners to become an independent producer, whereas the other nephew may regard his portion as the means of living in complete leisure as a pure consumer.

Jan 1, 1959

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By Harrison A. Schmitt

One of the great copper-producing areas of the world is comprised of five U. S. western states and northern Sonora, Mexico. The Southwest province of this area, covering southern Arizona, south- western New Mexico, and northern Sonora, produces some 55 pct of U. S. copper output and the equivalent of 15 pct of world production. In 1956 the area produced about 550,000 tons. Tucson is approximately the center of the oval- shaped province, which measures only 300 miles on its east-west axis and about 200 miles on its short axis. Northwest of the oval, and forming a tenuous connection with the Utah and Nevada copper fields, is an important operating mine, Bagdad, and also the now inactive United Verde. Along its north- south axis, running from Globe, through Tucson, to Nogales, ten moderate to major copper properties have been discovered or revived during the past 15 years, and five of these in only the past seven years. The latter five properties lie in an area 25 miles in diameter, centering 20 miles south of Tucson. In order of discovery, or revival, they are: Banner&apos;s Mineral Hill and Daisy; Cyprus et al&apos;s Pima; Duval&apos;s Esperanza; Asarco&apos;s East Pima (now called Mission mine) ; and Lewisohn&apos;s Peach. Total tonnage is estimated at about 250 million tons averaging some 0.90 pct Cu, but ultimate production may exceed this amount since some of the reserve is open ended.

Jan 6, 1959

By W. W. Mason

The US began exporting coal in the late 1800s, at first in very small quantities to Canada and, beginning in 1897 and 1898, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War I when shipments overseas increased from 7.3 Mt/a to 20 Mt/a. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War II when the US again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the US was the only country able to supply large quantities of coal at reasonable prices needed for reconstruction of the European economy, the US coal exports overseas expanded rapidly to 38.6 Mt in 1947. Additionally, we shipped 23.8 Mt of coal to Canada in that year for a total export of 62.3 Mt. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 69.3 Mt - a high that has not been reached since. Over the years the level of US coal exports has fluctuated fairly widely. Approximately 80-90% of all US coal exports are high quality metallurgical grade coal so our exports level depends directly on world-wide economic conditions and world steel production levels.

Jan 1, 1982

By J. D. Verhoeven

In the past 15 years a considerable amount of experimental and theoretical work has been done concerning the onset of convection in liquids as a result of interm1 density gradients. This work, which has been doue in many different fields, is reviewed here and extended slightly to give a rrlore quantitative understanding to the probletrz of conzection in liquid metal dlffusion experinletzts. In liquid metal systems the capillary reservoir technique is currently used, almost exclusively, to measure diffusion coefficients. In this technique it is necessary that the liquid be stagnant in order to avoid mixing by means of convection currents. Convective mixing may result from: 1) convection produced as a result of the initial immersion of the capillary; 2) convection produced in the region of the capillary mouth as the result of the stirring frequency used to avoid solute buildup in the reservoir near the capillary mouth; 3) convection produced during solidification as a result of the volume change; and 4) convection produced as a result of local density differences within the liquid in the capillary. The first three types of convection have been discussed elsewhere1-a and are only mentioned for completeness here. This work is concerned only with the fourth type of convection. Local density differences will arise within the liquid as a result of either a temperature gradient or a concentration gradient. It is usually, but not always, recognized by those employing the capillary reservoir technique that the top of the capillary should be kept slightly hotter than the bottom and that the light element should be made to migrate downward in order to avoid convection. In the past 15 years a considerable amount of work, both theoretical and experimental, has been done in a number of different fields which bear on this problem. This work is reviewed here and extended slightly in an effort to give a more quantitative understanding of the convective motion produced in vertical capillaries by local density differences. The Stokes-Navier equations for an incompressible fluid of constant viscosity in a gravitational field may be written as: %L + (v?)v = - ?£ + Wv - g£ [1] where F is the velocity, t the time, P the pressure, p the density, v the kinematic viscosity, g the gravitational acceleration, and k a unit vector in the vertical direction. A successful diffusion experiment requires the liquid to be motionless, and under this condition Eq. [I] becomes: where a is the thermal expansion coefficient [a =-(l/po)(dp/d)], a&apos; is a solute expansion coefficient [a&apos; = -(l/po)(dp/d)], and the solute is taken as that component which makes a&apos; a positive number. Combining with Eq. [3] the following restriction is obtained: Since there is no fixed relation between VT and VC in a binary diffusion experiment, Eq. [5] shows that the condition of fluid motionlessness requires both the temperature gradient and the concentration gradient to be vertically directed. Given this condition of a density gradient in the vertical direction only, it is obvious that, as this vertical density gradient increases from negative to positive values, the motionless liquid will eventually become unstable and convective movement will begin. The classical treatment of this type of instability problem was given by aleih&apos; in 1916 for the case of a thin fluid film of infinite horizontal extent; and a very comprehensive text has recently been written on the subject by handrasekhar.&apos; It is found that convective motion does not begin until a dimensionless number involving the density gradient exceeds a certain critical value. This dimensionless number is generally referred to as the Rayleigh number, R, and it is equal to the product of the Prandtl and Grashof numbers. For the sake of clarity a distinction will be made between two types of free convection produced by internal density gradients. In the first case a density gradient is present in the vertical direction only, and, since the convection begins only after a critical gradient is attained, this case will be called threshold convection. In the second case a horizontal density gradient is present and in this case a finite convection velocity is produced by a finite density gradient so that it will be termed thresholdless convection. Some experimentalists have performed diffusion experiments using capillaries which were placed in a horizontal or inclined position in order to avoid convection. These positions do put the small capillary dimension in the vertical direction and, consequently, they would be less prone to threshold convection than the vertical position. However, if the diffusion process produced a density variation, as it usually does, it would not be theoretically possible to avoid thresh-

Jan 1, 1969