Search Documents

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By M de Freitas Silva

One of the main steps during the decision-making process of long-term mine planning is the definition of the optimal sequence of extraction, which usually is synonymous with maximising the discounted cash flow of the project subjected to several constraints arising from aspects of technical, physical, and economic limits.Open pit mine production scheduling (OPMPS) comprises several intricacies related to its size and uncertainty of input parameters. Due to its complexity and prohibitive size, traditional mine planning usually relies on heuristic or metaheuristic methodologies which are able to provide good solutions in a reasonable amount of time. However, most of the uncertainty that surrounds the mining complex is ignored leading to non-realistic results.In this paper, a new heuristic approach is explored in order to solve a stochastic version of the OPMPS problem accounting for geological uncertainty in terms of metal content, multiple processing streams, and stockpiling option. The methodology involves generating an initial solution by solving a series of subproblems and this initial solution is improved using a network flow based algorithm.The algorithm was applied to a relatively large gold deposit with more than 119 thousands blocks. Results have shown that the methodology is promising to deal with large-size mine instances in reasonable time.CITATION:de Freitas Silva, M, 2014. Solving a large stochastic integer programming model for production scheduling at a gold mine with multiple processing streams and uncertain geology, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

IN this paper it is proposed to present certain features of operating practice at the Port Pirie works of The Broken Hill Associated Smelters Proprietary Limited, in the smelting in a blast furnace of lead ores carrying a high concentration of zinc.The subject matter selected for presentation is:(i) The effect of zinc on lead blast-furnace operations, together with an outline of the methods adopted in actual practice in dealing with the zinc problem.(2) Development of the height of tuyere above the bottom of the jacket, and the extension of the tapping interval and the combined effect of both factors upon the lead content of blast furnace slag.It will later be seen that one phase of the investigation carried out in connection with the effect of zinc on blast-furnace operations was largely responsible for the decision to increase to a marked degree the height of the tuyere above the bottom of the jacket.Due to this interdependence, it has been considered advisable to deal with the two features above mentioned.The high concentration of zinc in the lead-bearing materials smelted at Port Pirie has brought with it those troubles which are associated with zinc in the smelting operation.In the early stages of the history of The Broken Hill Associated Smelters Pty. Ltd. the trend towards increasing cost for labour, fuel, and stores, etc., rendered it necessary to increase the lead content of the charge, and reduce to a minimum the quantity of barren flux used.

Jan 1, 1931

By B Belle

In a predrained gassy coalmine, ventilation control plays a secondary role to the longwall (LW) goaf drainage systems to safely manage panel return gas levels. Typically, the LW specific gas emission (SGE) estimation models provide anticipated goaf gas emissions and arriving at required gas drainage capacity for various coal production scenarios. A study comparing the various LW goaf gas hole spacing patterns with weekly production rates of up to 270 kt/w of an operating mine with high SGE rates (~20 m3/t) was carried out. The goaf capture efficiency of LW panels ranged from 64 per cent to 85 per cent. For the first time, gas content of upper seam data post LW retreat were used to verify the current SGE prediction models. This study has shown that an average of 50 m goaf spacing is optimal for management of high production retreat gassy LW panels in presence of multiple upper and lower seams with gas emission zone influence reaching up to 200 m above workings. Due to the horizontal stress direction related geotechnical issues, goaf hole failures just behind the LW face is a recurring challenge resulting in significant and immediate increase in LW panel return gas levels. This paper highlights the shortcomings of current SGE prediction models for goaf gas estimation, and evolution of 50 m goaf hole spacing embedded in design process in managing the LW tailgate gas levels.CITATION:Belle, B, 2017. Optimal goaf hole spacing in high production gassy Australian longwall mines – operational experiences, in Proceedings Australian Mine Vent Conference 2017, pp 15–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S H. Burgmans, B Anderson

This paper aims to define the specific challenges relating to dredging fine tailings from an above ground storage facility for transferral to a mined-out pit. In addition, it compares dredging and mining perspectives on dredging of fine tailings.

Jul 1, 2021

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By Adams R. W

A commercial scale strong acid leaching plant was commissioned at the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, a member of the Pasminco group of companies, in February 1988. It was designed to upgrade the lead/silver residue product from 26% to 37% lead, thus improving the realised value and increasing overall zinc recovery. This in turn enables the lead smelter treating the lead residue to improve its productivity. The equipment consists of two 250m3 bricklined leach tanks and two 6.5m diameter stainless steel high rate thickeners operating with counter current washing at 95¦C and 120 g/L H2SO4. The present filtration and drying equipment is also being replaced. Two 35m2 squeeze action filter presses equipped with horizontal plates are being installed, together with ancillary drying equipment to ensure that the final product complies with the transportable moisture limit. The new filtration plant is due to be commissioned in mid-1989.

Jan 1, 1989

Solid Energy New Zealand Limited owns and operates the Ohai coal field (Wairaki Coal Mining Licence, CML) in western Southland. The Morley Stream passes directly through the middle of the CML and has required diversion in the past to enable open cast mining to proceed. Solid Energy is evaluating two new open cast pits at Ohai. Commissioning these new pits would necessitate further diversion of the Morley Stream. One of these potential new mines is adjacent to an abandoned State Coal Mines (State Coal) pit and there is an opportunity to substantially rehabilitate this old pit as a corollary to the new mine and the stream diversion project.   Past Morley Stream diversions were undertaken by State Coal and so they predated the Resource Management Act 1991 and the degree of community environmental awareness and involvement that has become the norm these days. Not surprisingly the design and construction of the historic stream diversions was based purely upon mining (operational) and engineering considerations. This led to the stream being diverted in a manner that achieved the clinical conveyance of design volumes of water from points A and B.   Solid Energy realised that the proposed new diversions need to adopt more holistic and environmentally sustainable design principles while also including appropriate mining and engineering constraints. This project involved the design of a 1.7 km diversion of the Morley Stream (median flow of about 1000 litres/second) that would enable progressive prestripping and development of the new mines and would also address final rehabilitation (of the stream), geotechnical risks, hydrological and ecological issues. To address all of these factors the project required a multidisciplinary approach. Moreover, it required a clear understanding of how the mining operational constraints could be integrated with the environmental considerations. A significant aspect of the project was how to take account of fishery instream habitat needs, the resource consent requirements and most of all, the involvement of key stakeholders such as the Fish & Game Council, Department of Conservation, the Iwi and local community in the design process. This was achieved through coordinated consultation and stakeholder involvement in a technical design workshop.

Jan 1, 2005

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of >6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J McCluskey, N Barros

"Long-term strategic planning at BHP Billiton’s Western Australia Iron Ore business aims for sustainable value maximisation of its large, long-life, low-cost, expandable mineral inventory and supply chain infrastructure. While mine plans are key components of this value equation, this objective requires a whole-of-business approach through comprehensive consideration and optimisation of the full value chain. Only through a system view do we believe that the value proposition of a set of plans is truly optimised.The fundamental considerations include: mineral inventory information, given its intrinsic uncertainty and risk/knowledge horizon a marketing view of future quality premium/discount based on overall market quality load whole of supply chain optimisation on a throughput accounting basis alternative sequences of capital decisions closure costs with significant magnitude of total movement requiring optimisation as part of the plan. In addition, the plan provides a view of acceptable uncertainty levels at different times in the future.BHP Billiton Iron Ore uses a structured Life of Asset planning process that supports the business with the optimisation of its maximum value proposition through a non-deterministic scenario-based optimisation approach on an annual basis. This is a key input to each year’s medium-term plans and budgets, including activities identified through a value of information approach that resolve the key uncertainties and steadily improve confidence in the plan.CITATION:McCluskey, J and Barros, N, 2014. Life of asset planning, uncertainty and value optimisation of the iron ore business – from exploration, to market, to closure, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

The subject of my paper is one which, I am certain, has exercised the mind of every man on whom depends the safe and economical conduct of mining operations; particularly in this district where the enormous size of the ore body has necessitated the mine workings assuming a scale that was hitherto unknown in the history of Australian mining. I, therefore, approach the subject with the feeling that I am displaying considerable t.emerity, knowing as I do that the subject has engaged the earnest attention and thought of everybody immediately concerned in the extraction of the ore of this district, and particularly of the Broken Hill lode.I think I shall not be contradicted in asserting that a very large proportion of eur accidents are distinctly traiceable to inexperience on the part of the miner, and records at the mines and verdicts of coroners' juries in many instances uphold this assertion by showing that the accident under notice was the direct result of lack of knowledge of the conditions of the work, or, at any rate, of an error of judgment hardly conceivable in the experienced miner. That this assertion is correct may also be proved by visiting any of the mines of the district.To the experienced eye it will be evident at once that a very large number are not in way skilful in the use of their tools and, therefore, lack the experience which of necessity must be coincident with the acquirement of skill. Now in making this' assertion, I do not intend to be too sweeping...

Jan 1, 1903

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

Collecting the clay fraction of active stream sediment from a flowing stream for geochemical analysis i a difficult process. One either takes a sample of dry fine-grained sediment from the stream bank (dry weather and dry sample are uncommon in parts of New Zealand and Tasmania), or dredges up a sample of sand and mud out of the stream.The latter method produces a soggy ample bag full of mud and sand, with varying amounts of gravel, depending on the size of the stream. The water can be filtered from such a sample by means of a Buchner filter funnel, but is difficult to obtain a vacuum in the bush. This problem can be solved by using a small hand- queeze bellows such as used in priming petrol pumps on outboard petrol motors. The common laboratory hand bellows is not powerful enough.A 70 mm diameter two-piece polythene Buchner filter funnel (Fig. 1) can be used. A length of rubber tubing is fitted around the inlet valve of the hand bellows and this valve is then jammed into the pipe at the bottom of the filter funnel (the polythene pipe may be trimmed with a knife to fit over the inlet valve of the bellows). The vacuum is generated and maintained by squeezing the hand bellows.The technique of collecting a sample of the clay fraction is to dredge a sample of the fine-grained active stream sediment out of the stream with a container, such as a plastic mug. The sample is agitated to get the clay fraction into suspension and the muddy suspension is then decanted into the Buchner funnel. The desired clay fraction is obtained as a thin film on the filter paper.If the "fines" are also required, a filter of nylon bolting cloth (stretched across the mouth of a short length of 80 mm diameter polythene pipe and attached by rubber bands or a concentric polythene pipe) can be placed over the mouth of the Buchner funnel and the whole sample of stream sediment...

Jan 1, 1969

By N Boughen, K Moffat, L Brooks, A Zhang

In 2015, Ernst and Young (EY) ranked socio-political license to operate (SPLTO) as the fifth greatest challenge to the mining sector (EY, 2015). The EY report asserts that SPLTO will continue to present a risk to the mining sector in the context of ‘increased activism, digitally connected stakeholders and politicians who need to respond to general consensus’. While there is no consensus on a definition, SPLTO is commonly regarded as the ongoing acceptance or approval of an operation by affected stakeholders (Moffat and Zhang, 2014; Thomson and Joyce, 2008) as well as those stakeholders that can affect the operation (Graafland, 2002). Warhurst (2001) relates the process of stakeholders granting SPLTO to the establishment of meaningful partnerships between operations, communities and government based on a variety of factors that build trust between stakeholders.From these accounts, we can see that understanding stakeholder attitudes about company performance and impacts on stakeholders directly affected by an operation are important in any attempts to measure SPLTO. Understanding the level of acceptance of an operation within these stakeholders provides a good proxy or outcome measure of SPLTO. Moreover, trust seems to be a central variable in the translation of these experiences of an operation into acceptance. What the mine or company does, its behaviour, degrades or builds trust with stakeholders, and this then affects acceptance (Moffat and Zhang, 2014).In addition, a strong emphasis is placed on the nature of the relationship between companies and stakeholders as influenced by inter-group interactions. It is not just what companies do well or poorly with respect to environmental impacts, for example, that will determine trust and acceptance, but how the company relates to its stakeholders at personal and group levels.These relationships between communities of stakeholders and extractive companies are dynamic. Brown and Fraser (2006) recognised the importance of industry being able to respond to the changing nature of societal approval and acceptance, arguing that ‘business must have regard for evolving social attitudes and expectations if it is to maintain its ‘social licence’’.This paper will describe a series of five pilot projects conducted by CSIRO with Anglo American in Australia and South Africa to generate a real-time understanding of SPLTO to guide more reflexive and effective social performance strategies.CITATION:Moffat, K, Boughen, N, Brooks, L and Zhang, A, 2016. Social licence in real-time – using dynamic methods to support a new kind of community relationship, in Proceedings Life-of-Mine 2016 Conference, pp 191–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By I Gray

This paper examines the effects of the changes in stress that a coal may undergo as part of the drainage process. As a consequence of this, some coal seams will come to the situation that they have zero horizontal stress existing within them at the time of mining. The hypothesis of this paper is that this lack of horizontal confining stress means that on mining, the vertical stresses may be easily raised to a level where failure occurs. This failure may be accompanied by significant energy release from energy stored within the coal as well as that coming from the roof and floor. To determine the state of stress within the coal seam, the concept of the effective stress path that the coal passes through is examined and is found to be very dependent on the shrinkage of the coal with degassing, the Young’s modulus of the coal and its Poisson’s ratio. The Young’s modulus of the coal is important and has been found to be highly dependent on the state of stress within the coal. It may change by more than an order of magnitude.CITATION:Gray, I, 2014. The consequences for pillar stability of zero confining stress brought about by forced or natural drainage, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014