Search Documents

The strategy of adjusting operating conditions to maintain optimum process performance as the feed quality varies - adaptive optimisation - is being investigated by computer simulation of chemical processes for the treatment of ores. Those ore-process systems that are most likely to yield substantial benefits from adaptive optimisation are being identified as a guide to the selection and development of systems for practical application. The generalised mathematical representation of the cost structure, ore quality variations, process kinetics, reactor characteristics and operating variables for ore-process systems is described. Results are summarised for temperature, reagent concentration or residence time as the manipulated variable. For almost all systems, adaptive optimisation was economically beneficial, although a few exceptions have been identified where there is a significant synergistic effect between poor-performance and good-performance materials in a blended feed. The sensitivity of the benefits of adaptive optimisation to a range of economic and technical factors is summarised.

Jan 1, 1985

By Pitkajarvi J

Waste rock dilution causes mill feed grade to be lower than mineral resource grade. In nickel mines relative grade decrease (dilution) may be tens of per cent because of irregular ore boundaries and weak wall rocks. Five per cent dilution costs millions of dollars annually in medium size underground mine. In Outokumpu Group selective bench and fill stoping, cable bolting/shotcrete-skin support and fast ore boundary definition (OMS-logg in-hole logging or sludge sampling) are the key tools in dilution control. Commitment of the whole organisation to keep dilution low is also needed. Dilution sources and effects are discussed with examples of the dilution control methods applied in Outokumpu mines.

Jan 1, 1996

The diverse nature of inadvertent mine fires does not lend them to general treatment. But evolving from the unfortunate fires over past years is a simple principle in dealing with all fires to bring combustion under control. Control, in brief, means that the products of combustion, themselves possibly still with fuel values, are not revitalised by addition of fresh air. There are problems with fire- fighting, especially with water, as this may lead to production of CO and H2. Panel ventilation upstream of the fire must be controlled to direct all air over the fire. Some advantages in fire fighting are found by the use of "sails". Early diagnosis of fires and early treatment are essential for safety of personnel and safeguarding and recovery of property. Preparedness extends to up to date documentation, but first hand knowledge also is invaluable to the diverse personnel gathered to fight a fire, and in the decision making Involved.

Jan 1, 1981

By Lin Bin, Qain Minggao, Qu Qundi, Yao Zhichang

This paper describes the application of a 89C52 chip microcomputer in hydraulic pressure information monitoring system of powered supports in a coal face, and the details of circuit and software of a monitoring system substation. Each substati

Jan 1, 1998

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

By Sakai S, Suga S, Bisque RE

Soil gases were collected on activated charcoal, analyzed by computerized mass spectrometry and treated with multivariate statistical pattern recognition to determine the diagnostic geochemical signature associated with the Okuaizu Geothermal Field in Japan. From this a geothermal model was developed and compare to 175 "unknown" samples in a 250 m spaced grid over 30 1Qn2 mapping the areas with a matching geochemical character. Faults and fractures were generally located by the presence of high molecular weight components. Following the initial survey, the faults in two specific areas were precisely located by a second survey with samples at 10-30m spacing. Where earlier geochemical surveys had placed anomalies 1-2 Km northeast of the geothermal center, the fingerprint survey accurately mapped the system and detected several faulted zones. It was not misled by hot springs located away from the geothermal System.

Jan 1, 1987

By DiStefano AB, Dale SG

This paper describes the laboratory study implemented to investigate the application of the subaerial technique to tailings disposal for the proposed Olympic Dam Mine. The results of the study and the resulting design parameters are presented. The subaerial technique of tailings disposal is described and the advantages of the method for disposal in arid climates highlighted.

Jan 1, 1984

The reduction in man's contribution to the Greenhouse effect will only be achieved by a number of small steps. Some steps will absorb carbon dioxide (CO2) from the atmosphere in slightly greater quantities, others will reduce the amount of carbon dioxide generated. This paper deals with the reduction of carbon dioxide by improving the combustion efficiency of petroleum fuels. Until recently most reductions in fuel consumption and air pollution have been brought about through mechanical adjustments to combustion equipment. Since the development of tetraethyl lead, little has been done to chemically modify combustion reactions to improve fuel efficiency or reduce emissions. During the past five years Australian laboratory and field trials with ferrous picrate treatment have demonstrated significant and economic gains in the combustion efficiency of diesel fuels. These studies have revealed that even under ideal conditions in diesel engines, carbon monoxide (CO) momentarily saturates the combustion chamber. This state reduces combustion rates, peak pressure and power and increases the risk of pollution. Theoretical, laboratory and field data are presented which support the mechanism by which the ferrous catalyst accelerates the oxidation of CO to the terminal CO2 thus reducing fuel consumption and the undesirable combustion products accompanying the CO saturation of combustion environments. While this paper deals principally with diesel fuels commonly used in mining operations, the catalytic effect of the ferrous ion is also shown to significantly reduce fuel consumption by petrol engines thereby promising a means to reduce the much larger contributions to the Greenhouse gases by automobiles.

Jan 1, 1989

By Huntington J. F, Green A. A

The quality of a photointerpreter's anno- tation of an image may be displayed by writing maps in which the pixels are shaded according to the number of times a pixel was seen to be on a feature. The map of grey tones is more valuable, if, for each grey level, a measure of quality is determined, which is the probability that a feature exists in a pixel of a given grey tone. From repeated annotations (at least four) of the same image by a single observer, it is possible to formulate a perception model which describes stochastic processes in the observer. From that model, it is possible to assign estimates of data quality for each observer to each grey tone. For two observers on the same scene, the 'mean' method of quantifying the grey levels is to assign a value equal to the mean of the ii,:lities for each of the two observers separately. For this example, the grey tones arr thus quantified at probability levels of 0.70, 0.80, 0.90 and 0.95.

Jan 1, 1977

By Dai Q

The mechanism of flotation of potash ores with long chain primary amines has been assessed. Since at high electrolyte concentration in saturated brine the electrical double layers of the interacting particles and bubbles are entirely compressed, the induction time measurements confirmed the elimination of kinetic factors associated with the energy barriers opposing particle-to-bubble attachment under such conditions as could be expected. The lack of the kinetic hindrance resulted in the correlation found between the contact angles on the KCl surfaces and the sylvite flotation measured under the same physico-chemical conditions. The iep values and acid numbers obtained for various Esso oils tested as extenders in the flotation of coarse potash ore fractions confirmed the base oils with high content of nitrogen-bearing compounds to be good extender oils. The performance of such oils could further be improved by dissolving in them a small amount of long-chain aliphatic amine.

Jan 1, 1993

By Callinan AN

Broken Hill Proprietary Company Limited have recently commissioned a 14 Megawatt power station adjacent to its underground coal mining operation at Appin NSW. The power station is fuelled by methane gas extracted from the coal seams 500 metres below the surface. The methane is compressed and cooled prior to its injection into the combustor of a single shaft gas turbine. The turbine is coupled through a reduction gearbox to an alternator. There is sufficient power generated to cover colliery load, with any excess being exported to Prospect County Council, which is the supply authority for the south western region of Sydney.

Jan 1, 1987

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

This paper discusses the concepts of core risk associated with mining projects and operations and illustrates the types of core geotechnical risks and consequences that may relate to a range of different mining methods, with recommendations on risk management procedures to ensure that the core risks are under constant and ongoing scrutiny and priority management focus. These core geotechnical risks can and should be identified at the initial mining method selection stage, during a feasibility study. They should form part of the auditing of the project and the decision-making regarding the project viability. They should then be built into the ongoing management structure of the project, right through into ongoing operations, with regular audit and review.

Jan 1, 2003

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

By R Castedo, P Segarra, L M. López, J A. Sanchidrián, A P. Santos

The cylinder test allows us to determine the expansion of a copper cylinder by the detonation of an explosive charge inside. This test, originally designed for military explosives, has been adapted for industrial explosives with non-ideal behaviour. From data obtained with this test and known physical relationships, an analytical procedure has been developed to calculate the Jones-Wilkins-Lee (JWL) equation of state parameters for five ammonium nitrate/fuel oil (ANFO) and six emulsion-type explosives. A new radial wall expansion function is proposed considering a non-zero initial velocity with the consequent positive Gurney energy at unit relative volume. A set of equations is established to determine the JWL parameters, three of them obtained at the Chapman-Jouguet (CJ) point and the other three at different relative volumes. These equations, along with some constraints to ensure a physically sound solution, are solved for the JWL parameters by a non-linear least squares scheme. A 2D Lagrangian axisymmetric finite elements (FE) numerical model is developed for each tested explosive to validate the analytical results, in terms of expansion histories, with good agreement. This confirms that the set of conditions, constraints on the parameters and least squares calculation used constitute a robust methodology that fully captures the physics of the detonation products expansion involved in the cylinder test.CITATION:Castedo, R, Sanchidrián, J A, López, L M, Segarra, P and Santos, A P, 2015. Jones-Wilkins-Lee parameters for civil explosives, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By Gibbons S. L, Ritchie I. M, Murr D. M

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1990

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By Martin T

High methane content of the medium volatile metallurgical coal mined from the Coal Basin mines causes very difficult mining conditions. Rapid desorption into the mine ventilation system limits coal production, requires huge fresh air quantities and creates mine safety problems. In workings deeper than 2000 ft (600m) gassy coal and heavy cover create outbursting conditions. Cross-measure methane drainage has reduced ventilation requirements on advancing faces, but degasifica- tion of virgin coal is needed to improve mining Conditions.

Jan 1, 1982