Search Documents

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

By Eri G

Ok ledi Mining Limited underwent a major transition from radio based truck dispatching to computerized dispatching for its equip- ment fleet in October, 1996. Modular Mining's Computerized Dispatch System was selected based on reputation and superior customer support. Modular's dispatch system is a fleet management system that uses computer, data communication and global positioning sys- tem technology to produce automatic, optimized haul truck as- signments. Optimization is achieved by equally distributing trucks to shovels so that truck queuing and shovel idling times are mini- mized. Computer illiterate mine operations personnel had to overcome a rather steep learning curve to use the high technology equipment. fortunately the system was able to be configured to use bitmap

Jan 1, 1997

Rock bolting and rock-bolting systems depend for success on attention to a number of simple techniques. Failure to appreciate this fact can lead to disappointing results. Careful study of rock characteristics and placement methods can allow a change to highly successful rock bolt per- formance. A number of examples are quoted to illustrate the sig- nificant improvement in results which can be achieved by use of the most suitable combination of characteristics.

Jan 1, 1971

By J Hadjigeorgiou

Underground mines often rely on ore pass systems to ensure the transport of ore and waste. Consequently, it is important to ensure the smooth operation of such systems. Ore pass degradation that may require rehabilitation results in production delays and high operational costs. The occurrence of hang-ups within an ore pass also leads to disruption of ore production. There are important safety concerns when worker intervention is necessary to re-establish material flow in the ore pass. In order to facilitate the design of ore pass systems, mining operations often rely on past experience, or semi empirical guidelines. This paper describes recent efforts to establish a comprehensive database on current practices; encountered operational problems and solutions in ore pass design in Quebec underground mines.

Jan 1, 2003

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By A G. Thompson, E Villaescusa, D Howard

The Western Australian School of Mines (WASM) has developed a facility for the static testing of full-scale ground support elements (Morton et al, 2007). The test facility consists of several stiff steel frames used to support the sample and a screw feed jack is used to load the sample. A large-scale punch test method has been developed to load various shotcrete configurations. The shotcrete is sprayed on to a rock substrate containing a centrally located circular disc. The rock and shotcrete sample is placed on to the sample frame and restrained on all sides. The circular disc is displaced at a constant rate by the screw feed jack which in turn loads the sample. Instrumentation measures the displacement and the load being applied to the sample through the loading disc. The testing method is described in detail and the results from the testing program are presented. The results show that it is possible through laboratory testing to simulate some of the mechanisms of shotcrete support reactions better than conventional beam and panel tests.

Jan 1, 2008

FaulIing west of the Mount Isa mine is described and is shown to be related to three groups of folds that have been recognized in the area. The first period of faulting postdates the first generation folding; these faulIs are regional faults (tectonic discontinuities) which are folded by second generation folds. The faulting accompanying the second generation folding divides the area west of the Mount Isa mine into four structurally and metamorphically identifiable blocks. The most prominent of these second generation faults is the Mount Isa Fault, which is characterized by a number of distinct zones of intense second generation folding and the presence of localized layers of mylonite. Only limited evidence for brittle deformation has been observed and the major movement appears to be associated with the plastic deformation of the rocks. Confined to the areas of second generation folding in the Mount Isa Fault are numerous third generation kink folds. A detailed description of the Mount Isa and other faulIs is presented together with evidence for their existence. The displacement accompanying this faulting cannot be established because of the complexity of the structure.Postdating these faults and all the folding of the area are minor cross faults.

Jan 1, 1973

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

By Bevan JE

The US Bureau of Mines is conducting research to improve the health and safety for underground coal miners, and the efficiency of the mining systems that are used. In 1986, the Bureau began a major research effort on the technology for computer-assisted mining systems for underground coal mines. The initial target was technology for continuous mining machines that would allow them to extract coal by computer-assisted operation. Technology areas being investigated include guidance systems, machine condition systems, computer systems, machine control, human-machine interfaces and planning. In each of these areas, individual system development has progressed to where underground testing of these systems will begin in 1991.In addition to coal extraction, the Bureau has also begun research for the development of technology for computer-assisted roof bolting. The Bureau is developing technology for a "smart" roof bolter that would be able to sense and analyze strata conditions to determine the requirements to provide a competent roof. The system would determine the location of the hole, drill the hole to length, and select and install the appropriate bolt.

Jan 1, 1991

By Lean P. J

The present The Zinc ODrporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) tailing dam (Site C) is expected to reach its terminal capacity late in 1985. Planning and design of new facilities for disposal of tailing after 1985 which includes new tailing dams (Site D) commenced during 1980. This paper briefly describes planning guidelines and specifications, location considerations, environmental aspects, operating strategy, engineering specifications, envirormental aspects and scheduling of works.

Jan 1, 1983

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By Godresse M, Turczynski G. P J, Driver I. J, Low G, Ozawa N

Geological evaluations of coal deposits have been traditionally undertaken in a somewhat manual manner. Information is collected downhole by chip sampling, coring and using downhole geophysical logging. This information is then interpreted by an experienced geologist to define the coal and noncoal lithological units. Coal units were subsequently correlated to provide data for structural modelling. In recent years a number of advancements in interpretation techniques have been made based on Artificial Intelligence. This paper describes an integrated geological interpretation system based on maximised use of Al techniques. The first part describes the lithological interpretation which uses a number of boreholes with both logged lithology and downhole geophysical logs. This information provides a learning set of data to the neural network. The second part concentrates on the correlation of both coal and noncoal units from borehole to borehole. Problems in this area, in a manual sense, are interpretation of correlation across weathering zones and other geological anomolies. The technique is based on pattern recognition and dynamic programming techniques where a correlation matrix is developed relating all holes with their maximum correlations.

Jan 1, 1995

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste land form. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using the Daydream embankment at Fortescue Metals Group's (FMG's) Cloudbreak Operations as a case study.

May 1, 2010

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

A rapid automated search method, developed for the location of native gold grains in polished sections with a scanning electron microscope (SEM), has been extended to locate platinum group elements (PGE), in particular platinum and palladium, and their minerals down to 1 ¦m in size. Problems associated with the search for PGE minerals are discussed and examples of PGE minerals located with the facility in drill core sections, crushed ores, and metallurgical test products are given.

Jan 1, 1991

By Walraven F, Knott G. G

Using a typical small logging instrument (Neltronic KPD), a natural gamma reference section for part of the Brockman Iron Formation and part of the Mt. McRae Shale has been established in the Newman area. This is compared with the stratigraphic type section of Trendall and Blockley (1968). Folding and faulting are recognised using natural gamma logs. Because of the confidence with which stratigraphic horizons can be identified, less expenditure on diamond and percussion drilling is required to confirm stratigraphic position. Using natural gamma logs as stratigraphic control the apparent thinning of the Banded Iron Formation during iron enrichment is Demonstrated.

Jan 1, 1973

Ok Tedi Mining Limited commenced construction in mid-1981 of facilities and infrastructure to mine and process gold ore at Mt Fubilan in Papua ew Guinea. Production ofgold began more or less on schedule in mid-1984 although design capacity is yet to be achieved. Due to geotechnical problems, two important items of infrastructure, hydropower and permanent tailings disposal, are not yet in place. Current low metal prices make it likely that copper facilities will be postponed.The deposit compriscs a leached gold capping overlying copper sulphide porphyry mineralisation containing significant gold and molybdenum. Mining is by open pit methods. The soft leached capping gold ore is ripped and dozed, loaded by hydraulic shovel and trucked to a dump pocket. After passing a large semi-autogenous mill of nominal capacity of I, I00 tonnes per hour, the ore is treated by the carbon-inpulp process, with a gravity circuit to recover coarse gold. The final product is 12 kg dore bullion bars.At present, all tailings are detoxified with hydrogen peroxide; after cycloning, the coarse fraction is stored, and the slime fraction discharged into the river system; expected environmental impact is acceptable. Investigations for a suitable dam site for a permanent tailings system are still underway.Peak 'I. hour power demand for Stage I is 17 MW, presently supplied by a diesel alternator power station and a 2 MW mini hydropower plant.Initial access to the base camp at Tabubil was only by air. Eventually a road was pushed through 134 km from the river port at Kiunga (where port facilities have been constructed) and a further 23 km to Mt Fubilan.Roads are constructed of compacted gravel and crushed limestone generally underlain by geofabric. Eight major steel bridges were built.The town of Tabubil has been established, including housing, airport, shops, offices, schools and all facilities.Environmental studies have been extensive and a detailed monitoring program is maintained. Ok Tedi Mining Limited is making considerable efforts to train Papua New Guineans and to foster local business.

Jan 1, 1985

By C F. Nichol, L Smith, R D. Beckie

A better understanding of the hydrogeology within mine waste rock and cover systems is essential for the quantification, prediction and prevention of metals loading to the environment surrounding waste rock piles. The effect of surface condition on the internal flow mechanisms within an intermediate-scale constructed waste rock pile is being investigated at the Cluff Lake Mine, Saskatchewan. Changes in the water balance, the outflow distribution and water residence time have been observed in the waste rock pile following successive modifications of the surface condition. The three year old, run of mine, free-dumped surface was ripped to a depth of 30 cm to 40 cm, and levelled in October of 2001. In August 2002, a 10 cm to 15 cm cover of compacted waste rock was placed on the pile. Outflow, precipitation and run-off data collected during natural and artificial rainfall events have been used to quantify the maximum infiltration rate, and the spatial pattern of discharge and cumulative volume of water that infiltrated into the waste rock under each surface condition. Infiltration data together with the outflow data provide a basis to address the residence time of water within waste rock and the dominant flow mechanisms for different surface conditions. With a free dump surface spatially distinct wetting fronts are observed at the base of the pile that vary in flow rate by an order of magnitude (measured at a 2 m by 2 m scale) and in time by up to a week. Following ripping and levelling, similar cumulative outflows were observed, but the magnitude and arrival time of wetting fronts changed across the pile. A decrease in outflow volume, a decrease in infiltration volume, a two-fold increase in the response time of wetting fronts and a more spatially uniform distribution was observed following placement of the compacted surface layer. Based on preliminary data, the internal structure appears to be the dominant factor controlling outflow variability.

Jan 1, 2003

By M Bannear, J-F Wilhelmy, R Jones

Mineralogical study of the interactions between fluxes and iron-oxides helps to understand how magnetite oxidises to haematite during pellet firing. Samples of OneSteel magnetite pellets tested at COREM pilot plant were collected after three firing steps and were studied mineralogically. Preheated pellets revealed no particular microstructures related to the composition of fluxes but were more affected by their bed position. After kiln firing, the impacts of lime and magnesia became more apparent. Magnetite oxidation is complete in the cooling stage. The position and the microstructure of the residual magnetite can bring useful information that could æcompleteÆ the view of the firing cycle.

Jan 1, 2007