Search Documents

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Bill Almdal

Today?s presentation ? Role of the Regional Issues Working Group ? What does RIWG do? ? How can RIWG?s work benefit Stakeholders? ? Review of forecasts vs. reality ? How have past investment compared to the reality? ? Risks to future growth ? The growth potential is very high and so are the risks ? Examples of outputs ? Housing needs ? Growth in population ? Tires for large trucks The Regional Issues Working Group ? Our vision ? To provide a proactive process which promotes the responsible, sustainable development of resources within the Regional Municipality of Wood Buffalo for the benefit of all stakeholders ? What we do ? Facilitate planning for growth ? Facilitate effective and efficient resolution of issues ? Involve all of the resource developers and affected stakeholders in planning ? Develop plans for sharing benefits with Aboriginal stakeholders ? Benefits for Stakeholders ? Our forecasts include up-to-date information from all developers ? including information on employment and housing needs ? Our forecasts are the basis of planning for many stakeholders ? and can assist in their development planning

May 1, 2002

By Charles Knilans, Tassos Grammatikopoulos, Nicole Hoffmann

"Twin Metals Minnesota LLC, (TMM) has recently completed a prefeasibility study evaluating the development and operation of an underground copper (Cu), nickel (Ni), platinum (Pt), palladium (Pd), and gold (Au) mining project on the Maturi deposit in northeastern Minnesota.The Maturi deposit is a magmatic Cu-Ni-sulphide deposit occurring along the basal contact of the South Kawishiwi intrusion, comprised of heterogeneous troctolites to gabbros forming a tabular body designated the BMZ (basal mineralized zone). These rocks provide the major gangue mineralogy (plagioclase, olivine, and clinopyroxene) with local, minor rock-forming orthopyroxene, biotite, magnetite, and ilmenite. Altered silicates exist within local fracture and/or alteration zones, which are commonly associated with minor faults in the regional area. The Maturi deposit is comprised of four main mineralized zones within the BMZ, referred to as Stage 1, Stage 2 (S2), Stage 3 (S3), and Upper Heterogeneous. Chalcopyrite, cubanite, pentlandite, and pyrrhotite are mainly hosted within the S2 and S3 units, with talnakhite frequently occurring within the S3 unit.A cross-discipline approach combining geology, geochemistry, metallurgy, QEMSCAN™ mineralogy, and mine planning has been implemented to develop a preliminary geometallurgical model and life of mine metallurgical performance forecast. This paper provides an overview of the methods that were used to develop the model and forecast, and discusses the advantages of such a model in project development and evaluation.INTRODUCTIONThe TMM Project proposes mining a copper-nickel-palladium-platinum-gold-silver (Cu-Ni-PGM) magmatic sulphide deposit situated in the Duluth Complex of northeastern Minnesota, USA. The prefeasibility study proposes a 45,000 million tonnes per day mine and concentrator facility to produce two saleable concentrates. The mine will access two separate deposits, Maturi and Maturi Southwest. Saleable concentrates are the final products of the sequential flotation plant where a high grade Cu concentrate is produced followed by a Ni concentrate."

Jan 1, 2015

By Gillyeard J. Leathley

The Cassiar Asbestos mine is situated on McDame Mountain in northern B.C. at a mean elevation of 6000 ft (1830 m), some 6 miles (9.6 km) from the townsite /mill complex. Asbestos ore production averages 1,200,000 tons at 9% R.M.G. (Recoverable Mine Grade) and waste production is 6,000,000 cu. yd annually. Waste is loaded by P&H 1900 AL 11-cu.-yd shovels and transported by 75-ton and 85-ton end-dump trucks to the waste dumps. The ore is loaded by a 992 Caterpillar 10-cu-yd front-end loader into 50-ton and 75-ton trucks, which transport it to the crushing plant located at the mine. The ore is transported by a 15,370-ft (4685-m) tramline to the mill complex.

Jan 1, 1978

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By Gordon S. Farnham

THIS paper summarizes the results of investigations carried out at Sydney Mines, N.S., and at Ottawa, following the disaster at Princess colliery, December 6th, 1938. The Honourable Minister of Mines for Nova Scotia appointed A. E. Cameron special investigator to enquire into and report upon the cause of the rope failure. Public hearings were held in Sydney Mines and evidence taken from many witnesses. The site of the accident was examined in detail and investigations made of the rope layout and colliery practice. At the request of the special investigator, the Department of Mines and Resources, Ottawa, kindly undertook technical and scientific examination of the broken ends of the rope. These investigations were carried out in the Metallurgical Laboratories of the Department of Mines and Resources, under the supervision of G. S. Farnham, Metallurgist for the Department. Valuable assistance in interpretation of many features of the investigation was received from other sources. Acknowledgment is due to Messrs. Stuewe, McCall, and Gordon, and other members of the staff of the Dominion Steel & Coal Corporation; to Messrs. Morrison and Scott, and other members of District 26, United Mine Workers of America; and to Messrs. Timm, Parsons, Haycock, Haanell, and other members of the staff of the Department of Mines and Resources, Ottawa, for helpful ad vice and technical assistance in assembly of information, and preparation of material and interpretation of evidence obtained.

Jan 1, 1939

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By N. Pajunen, R. Mäkikoskela

"The current state of environment has been achieved by acting linearly. At the same time, we know that transition towards circular economy cannot be made the same way that we have used to, trusting only a market economy and economic growth. Environmental improvements have been promoted, some progress has been made, but major steps towards sustainability have not been taken. Industry is now facing significant change, from process related environmental thinking to product-based environmental thinking.Engineers make decisions which have lifelong influence and even longer on environment and society. Material engineers in case of saving natural resources and increasing material cycle, have an important role to play in the transition towards sustainability. Best knowledge of minerals and materials is in the material development phase. If we want to increase the cycle of different materials, it is vital to make decisions towards circular economy in early phase of product´s life cycle.The target of this study is to promote circular economy; to increase material efficiency; to save natural resources; and to extend product lifecycles in process industry via product design and material development. In this study we have a new kind of cooperation. We combine two disciplines, engineering science and fine arts. We promote sustainability via breaking out the silos. We bring the cyclic artistic thinking into engineering science and environmental research. The new research combination makes the existing information visible in a new way, and it will change attitudes and ways to act by means other than traditional linear rationality.We have tested the new working method via the industrial case study with the chosen product: the sandwich panel of construction industry. The target of the study was to create something new from the chosen product with artistic thinking. The working method will be presented in this paper."

Jan 1, 2016

By P. Hajiani

"Feasible and sustainable separation of lanthanides outside of China has been a dilemma for the past few years. The present technique uses REE electrophoretic mobility (Ui) variation in an electrical field to separate them. The present invention relates to a system and a method to separate and refine rare earth elements/compounds produced in hydrometallurgical processes while they are dissolved in an acidic medium, without any intermediate precipitation step. This process uses free-flow electrophoresis to isolate REE from the concentrate simultaneously without any pre-treatment or intermediate steps related to the nature of elements.INTRODUCTIONRare earth elements (REE) invariably occur together in nature, and any given mineral contains several or most of them. Production of high purity individual rare earth (RE) elements/compounds from their ores generally requires two stages of processing, including mineral processing and hydrometallurgy.Depending on the ore, mineral processing and hydrometallurgy treatment of the ore before REEs purification is relatively simple and quite achievable though conventional methods. However, producing individual REE from mixed REs compounds is tremendously tedious. RE processing often requires dozens of steps, each resulting in minute improvement in the complex RE streams. Separating and extracting a single REE requires a great deal of time, resources, and expertise. Today, advanced RE refinery facilities cost hundreds of millions of dollars to build. The high purity RE concentrates are separated into individual REE using solvent-based or ion exchange methods. Although there are several techniques to separate REEs, most of them suffer from different types of drawbacks. For instance, solvent extraction requires a great number of steps to achieve high purity REEs. The process which uses ion-exchanger for separation and refinery operates with low REE concentration in solution which leads to very large liquid volume quantity, bulky tanks, dehydrators, pumps, etc. The low concentration will adversely affect the water consumption as well as other chemicals. Similar chemical properties of those three valent elements do not allow them to be isolated easily one from one another using conventional separation techniques. Solvent extraction has been successfully applied for rare-earth refining (lanthanide, scandium and yttrium) for the past few decades in China. Since then, efforts have been dedicated to develop other techniques which could be applied industrially around the world."

Jan 1, 2016

By D. du Plessis, R. Stobbs

The Canadian Clean Power Coalition (CCPC) was created in 2001 to protect and enhance Canada’s vast coal and other carbon-based resource wealth, and to ensure that environmental public policy decisions recognize that these resources are a Canadian asset, not an environmental liability. To achieve its mandate, CCPC has undertaken to demonstrate technologies for use in new coal-fired power plants to control air emissions including carbon dioxide (CO2), nitrogen oxides (NOx), sulphur dioxides (SOx), mercury (Hg), and particulates (PM). The first phase of the demonstration project assessed three existing technologies for coal-fired power plants that reduce all emissions, including CO2, to levels equivalent to or below that of gas-fired power plants. The technologies considered in this phase included integrated gasification combined cycle (IGCC), ‘oxyfuel’ combustion, and amine scrubbing of pulverized coal. These technologies were evaluated with three coal types: Eastern bituminous, western sub-bituminous, and lignite coals. This paper presents the studies, conclusions concerning the capital and operating costs of these technologies, the cost of electricity produced (with CO2 removed), and the cost per tonne of CO2 avoided. It also discusses the potential for using captured CO2 for enhanced oil recovery, and possible technology enhancements for improving the competitiveness of gasification of low-rank western Canadian coals. The second ongoing phase of CCPC’s work includes the design and construction of a commercial-scale plant to demonstrate the feasibility of integrated gas combined cycle (IGCC) and/or polygeneration technologies and the potential for using the CO2 generated for enhanced recovery of conventional oil.

Jan 1, 2006

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946