Search Documents

By M. J. Slater

Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. Continuous fluidized-bed ion exchange is an advantageous technique for processing dirty effluents and thin slurries. It also reduces resin inventory and equipment cost compared to fixed packed beds. A simple continuous fluidized-bed unit has been investigated for treating effluents and its performance is described. Breakthrough curves were first obtained from static fluidized fixed beds; these data were then used to determine the required operating conditions for a periodic-flow, countercurrent fluidized-bed ion exchange system. A waste stream, containing about 56 ppm copper, was treated in the continuous system using an extraction fluidized bed depth of 203 cm and a flow rate of 1.22 cm3/ cm2s (900 gph / sq.ft) to yield an effluent containing less than 0.02 ppm copper. A generalized design method is proposed for similar chemical systems.

Jan 1, 1978

By Alex Cormode, Carlos Perucca

"Sylvinite ore from the Saskatoon area typically contains about 5% insolubles, occurring as clays and carbonates. These insoluble slimes must be removed sufficiently well to permit an efficient subsequent potassium chloride flotation, due to their high adsorptive capacity for amines used as potash collectors. The insolubles are liberated from sylvinite by high attrition scrubbing in a slurry. The liberated slimes are separated by multistage cycloning or by a selective flocculation-flotation process.An outline of the potash processing operations at Agrium Vanscoy Potash Operations is given, emphasizing the insoluble slimes froth flotation separation process. This process was originally implemented at the Agrium plant in the mid- 1970's and replaced a hydrocyclone system.IntroductionAgrium Vanscoy Potash Operations is located 40 Km southwest of Saskatoon, almost midway between the communities of Vanscoy and Delisle. Processing operations started in 1969, and the annual production capability was subsequently increased to the current 1.8 MM tonnes per year of muriate of potash.The mining operation at Agrium Potash which was described in a paper by Jones and Pruggerl , is done underground using four large continuous double rotor boring machines for the main production with development done by heliminers. Annual ore production is 5.5 MM tonnedannum. Ore is hoisted 1,100 m to surface for processing."

Jan 1, 1999

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By F. J. Alcock

The Appalachian region of Canada comprises the three maritime provinces; Nova Scotia; New Brunswick; and Prince Edward Island; and that; part of the Province of Quebec lying south and east of Logan's fault. This; major thrust runs in a gently curving line from lake Champlain to Quebec; city and thence down the valley of the St. Lawrence to pass between Anticosti; island and Gaspe peninsula. To the northwest lies the St. Lawrence; Lowland division of the Interior Plains geological province; a region underlain; largely by early Palxozoic strata; which for the most part lie horizontal; or with low dips; where faults occur they are predominantly of the normal; type; and only locally are the beds cut by intrusive rocks. To the southeast; on the other side of the fault zone; an entirely different set of conditions is; encountered. There; Lower Devonian and older strata stand at high angles; are sheared and thrust faulted; and are intruded in many places by granitic; igneous bodies. The present paper is designed to outline briefly the geological; and structural history of this geological province and to emphasize; the part that structural conditions have played in connection with mineral; deposition.

Jan 1, 1954

The Environmental Excellence in Exploration (E3) project is driven by the recognition that the minerals industry can only maintain its long term viability by ensuring its continued access to lands to explore for, and develop, new mines. Widespread implementation of sound environmental management practices by the exploration community and improved education and understanding of that by stakeholders will help substantially in accomplishing this, and E3 is designed to meet these needs. Exploration crews are now viewed as ambassadors for the global mining community. Their performance in managing the environmental aspects of an exploration program can demonstrate a commitment on the part of the international mining sector to environmentally responsible exploration and mining. We have all observed that failure to behave responsibly can alienate local residents, encourage anti-mining NGOs and jeopardize development. As the saying goes, ?you don?t get a second chance to make a first impression?, and we want to make a favourable first impression. The E3 project is focused on creating an electronic manual, the e-manual, which will provide rapid access to the most up-to-date information on environmental management practices for minerals exploration globally. The e-manual will reflect current thinking and practices in environmental management. It will be richly illustrated with actual examples that reflect the realities of exploration. It will strive to identify the key environmental issues and concerns that apply to most exploration projects, and identify other sources of relevant information useful to field practice. It is our belief that E3, or something very like it, is central to ensuring that the industry survives the current challenges to its viability. E3 will be a cornerstone of the mining industry?s drive to sustainability simply stated, if we are not permitted to explore for mines, there will be none of them at some point in the relatively near future.

May 1, 2002

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By M. Lahtinen, P. Latostenmaa, I. Kojo, E. Peuraniemi, M. Lindgren, S. Jyrkönen, M. Jåfs

The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. Since then Flash Smelting technology, now owned and developed by Outotec Oyj and the first plant, now owned by Boliden Harjavalta Oy, have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a popular theme during the first days of Flash Smelting, it has still been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. This paper describes the history and improvements of the Outotec® Flash Smelting process by looking into the early days of operation and how the development of the process and equipment has taken place over time as a joint effort between the technology provider and the users of the technology. INTRODUCTION In the 1940s, Outokumpu Oy refined the concentrate produced in the Outokumpu mine into metallic copper initially in Imatra, and later from 1945 to 1949 in Harjavalta, based on the most modern electrical melting process of the world at that time. After the war, Finland lost a significant part of its hydropower production, and due to the increasing use of electricity, the availability of electricity weakened, and the price rose. To maintain Outokumpu's profitability, it was forced to look for a melting solution that was not based on electricity.

Jan 1, 2019

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By H. Salamanca

HighService has developed different equipment using wireless technology and machine vision systems that were specially designed to allow 1) the online determination of the SAG mills liner's service life, 2) the automatic detection of a missing dipper tooth in mineral extraction shovels, 3) the reduction of accident risk potential in the mineral transportation within the mine, and 4) the reduction of collision risk potential between shovels and wheel dozers during mineral extraction. For the development of all these systems at HighService, extensive research has been done in radio frequency and image processing fields. The integration of both technologies with the expert knowledge of the company on the typical harsh environment conditions of the mining industry has led to the development of heavy duty equipment that tolerate the extreme mechanical requirements of SAG mills and electrical mining shovels.

Jan 1, 2007

By J. E. Gill

"The Wasa Lake property is a block of about 1,640 acres in Beauchastel township, Quebec. Gold was discovered there first in 1936 in what is now known as the 'Southern area ( Fig. 1). Stripping and trenching were followed by 9,218 feet of diamond drilling in twenty holes. A number of good intersections were obtained, but their interpretation in terms of ore was difficult. A shaft was then sunk to 220 feet vertical depth. Thirteen hundred feet of lateral work and 543 feet of diamond drilling were completed at the 200-foot level before work was discontinued in 1938. Results up to this point had been just fair.Early in 1944, surface diamond drilling was resumed. The first hole cut material of ore grade in a strong shear zone 1,000 feet north of the old workings, and holes to the east and west showed this to be an extensive gold-bearing zone.In August 1945, a main working shaft was started. This has been sunk to 550 feet slope depth. A cross-cut at 390 feet vertical depth was driven to the ore zone and, by drifting and drilling at regular intervals, a length of 725 feet had been tested to December 31st, 1946 ( Figs. 1 and 2). The results check those from surface drilling quite closely.In the main zone, scoping widths from 8 to 40 feet and averaging about 25 feet are indicated. The grade after dilution should be about 0.15 oz. gold a ton and operation will probably start at 1,000 tons a day."

Jan 1, 1954

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By George Kellock

Introductory The Alberta Provincial Government has contemplated a revision of the Mines Act for some time past, and it is understood that a definite decision has now been made to do this at the next session of the Legislature. The Operators' and Miners' organizations of the Province have been asked, or at least have been given the opportunity, to submit their views and ideas relative to the proposed changes. The operators have already drafted out a number of changes which they feel would improve the Act from the standpoint of safety and practicability, and this paper has been prepared so that the general membership of the Rocky Mountain Branch of the Institute, which is composed largely of the operating and certificated officials of the mines, might have an opportunity to discuss, criticize, and improve upon the suggested changes which the operators are putting forward.

Jan 1, 1929

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By I. Farr, H. Wittens

"In 1989 and 1990 abnormally high levels of arsenic in ore from the Thompson Open Pit Mine threatened Manitoba Division's electro-nickel production. The paper will discuss our development of a flotation process to separate pentlandite and gersdorffite (the prime nickel and arsenic bearing minerals).The presentation will focus on the development of the process from conception, through lab and plant test work, to plant optimization and full scale production. The paper will conclude with the benefits and cost of the completed project.INTRODUCTIONRejection of arsenic from nickel sulphide ores was not a primary concern in the Manitoba Division until 1989. At that time increased production in the Thompson Open Pit mine, which contains high arsenic ore zones, resulted in excess amounts of arsenic in the Thompson Refinery affecting electro-nickel quality. This problem was resolved through extensive efforts by Mill personnel. The purpose of this paper is to familiarize the reader with- the Thompson Mill.- the mineralogy of the Thompson orebody.- the evolution of Ni/As separation in the Mill.- the metallurgical impacts of the separation on the Mill.- the importance of the separation to the Manitoba Division."

Jan 1, 1991