Search Documents

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By N. Torres, G. Melcher

"An alternative to building new copper smelters, because of either stringent environmental regulations or in order to expand current plant capacity, could be achieved through the retrofitting of old reverberatory furnaces by making use of tonnage oxygen. The CONTOP® technology offers unique advantages over other techniques for this purpose, especially regarding substantial reduction in bath, capital and operating costs. This is possible to achieve since the reverb throughput could be largely increased with no major structural modifications to the furnace.The following options are offered to the smelter operators: dirty concentrates can be treated in an adjacent Contop system, or the cyclones can be mounted on the reverb roof for either dual operation or full Contop operation. ln the tatter case the furnace will be used as a settling chamber and f or slag c1eaning by top blowing with reducing gases.By incorporating Contop technology, the furnace throughput can be increased, higher malle grade, fixation of sulphur from furnace off-gas and substantial savings in energy consumption are possible to attain.IntroductionCopper smelting has been revolutionized during the last quarter century to such an extent that the standard type of plants consisting o f roasters and reverb furnaces seem a thing of the past, or almost. Though the building of new, more energy efficient smelters is a very likely opportunity for a grassroots plant, it would be hardly justifiable to replace an old existing plant unless there are heavy environmental or economic constraints(1,2,3)."

Jan 1, 1984

By Jochen Petersen, Caroline Muzawazi

The technical feasibility of ammonia leaching of PGM bearing Platreef flotation concentrates was investigated as an alternative method for the recovery of base metals prior to precious metal recovery. The composition of the concentrates includes 2.02% Cu and 3.17% Ni, and the major base metal minerals are chalcopyrite and pentlandite. Optimal leaching conditions were initially established in shake flask experiments to be a solution containing 4 M NH4OH, 4 M (NH4)2CO3 and a pH range between 9 and 10. These were used as base case conditions in column and batch stirred tank reactor tests, where the effects of total ammonia concentration and operating temperature were explored further. At optimal conditions nearly 100% Cu and Ni extraction were obtained in the batch stirred tank reactor, and 95% Cu and 60% Ni extraction was obtained in columns. The activation energy for chalcopyrite and pentlandite was 36 kJ/mol and 16 kJ/mol, respectively, in both reactors, indicating different reaction pathways for the two minerals. Gas-liquid mass transfer appears to be the limiting reaction step in columns much more than in tanks, and the degree of ammonia loss to air is significant. This initial test work indicates the feasibility of using ammonia leaching for this and similar materials as an alternative route to conventional smelting and refining prior to PGM recovery, but a number of technical challenges still need to be overcome.

Jan 1, 2014

By D. Tao

The adverse effects of clay particles on coal and mineral processing processes such as gravity separation, flotation, filtration, and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed largely to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of clay binding agents developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical and column flotation tests were carried out using coal and potash samples. Process parameters investigated include slurry solids percentage, impeller rotation speed, binder dosage, collector dosage, etc. Flotation results show that use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time was about 1 lb/t and 0.5-1 min, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Jan 1, 2006

By Dave Thomas

?Uranium is a common trace metal at the earth?s surface, but these are amazing super-high grade (up to 25%) pods, veins and disseminated uraninite (UO2) near unconformities between Proterozoic siliciclastic red beds and metamorphic basement with graphitic metapelite and radiogenic granite. ?Pitchblende fills extensional features in reactivated fault zones and replaces matrix in sandstone ?One mining district in Canada ?the Athabasca Basin ->30 deposits /prospects -most in eastern ¼of basin -produces 1/3 of world?s U -employs northerners -VERY high tech -VERY high safety standards Unconformity-associated uranium depositsUnconformity-deposits

May 1, 2006

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

By Alexander Smith

"The Silver Standard mine is 6 miles by road northwest of New Hazelton, B.C., a small town on the northern line of the Canadian National Railways some l 75 miles northeast of Prince Rupert. The deposits lie on the western slope of Glen Mountain (elevation 2,100 feet), with the main adit, mill, and campsite at 1,300 feet. The deposits were found in 1910, shortly after the area had been swept by forest fire and during a period of prospecting activity spurred by the construction of the railway. Crude ore only was shipped until 1918, when a 50-ton gravity mill was built which operated until 1922. Gross value of production of this period, at present metal prices, was about $1,000,000.In 1947 the present company was formed and a 50-ton flotation mill installed. Production from 1948 to 1955 has been in excess of $10,000,000, and net smelter returns about two-thirds of this amount. More than 60 per cent of the production and 80 per cent of the profit have come from one vein, No. 6. On the 1,300-foot level this vein had an ore section 375 feet long and 2.5 feet wide, averaging 0.18 ounces gold, 85 ounces silver, 10 per cent lead, and 16 per cent zinc.The mine workings follow a simple pattern. A series of parallel veins, striking northeast and dipping southeast, are numbered from 0 to 12, starting at the northwest. They lie within a zone trending south 70 degrees east, and the distance between Nos. 0 and 12 veins is about one mile. Recently several cross-veins, dipping northeast, have been found between Nos. 8 and 12. They are apparently of the same type as the others, though they may not have the same structural controls. They could be an important new source of ore.The mine has been developed principally by crosscut adits at the 1,500- and 1,300-foot levels and a 510-foot shaft with levels at I, 150, 1,000, ·and 850 feet. Drifts and crosscuts total 17,000 feet, chiefly on Nos. I, 4, 6, 7, and 8 veins. The drifts are stoped by shrinkage, top shrinkage rill, cut-and-fill with resuing, or open stope methods. The mill produces a lead-silver-gold-copper concentrate and a zinc concentrate, with indicated recovery of more than 96 per cent (4)."

Jan 1, 1949

By T. S. Smith, C. C. Rennie

"THE LEAD-ZINC and tungsten mines of Canadian Exploration Ltd are on Iron Mountain, 8 miles south of Salmo, B.C., in the Nelson mining division. Relative location of the mines is shown on the general plan.First recorded lead production was in 1908 from surface outcrops. Small amounts of high lead ore were mined intermittently until 1926. No major lead-zinc production occurred until 1949 when outcroppings on the south side of the mountain were mined and diamond drilling began to prove the existence of a large replacement orebody. Lead-zinc ore has been mined continuously from the Jersey orebodies since March 1949, with monthly tonnage as high as 50,000 tons per month, but currently averaging 30,000 tons per month.Schee1ite-bearing tungsten ore was found in 1942 by H. Lakes in an old adit and open cuts at the north end of the Emerald tungsten orebody. The Emerald tungsten mine was developed by the Federal Government as a Wartime Metals project and operated for eight weeks in the fall of 1943, when the poor demand for tungsten closed the mine. Canadian Exploration Ltd. purchased the mine in 1947 and mined in excess of 100,000 tons in 1947-48 until the demand for tungsten dropped again and interest was centred on lead-zinc. The Federal Government repurchased and reopened the Emerald Mine in 195 L and built a new concentrator. The mine and mill were sold back to Canadian Exploration Ltd. in 1952.Regional Geology and IntrusivesThe host rock for both the lead-zinc and tungsten mineralization is the Laib formation of Lower Cambrian age, which consists of 400 feet of crystalline limestone underlain by beds of argillite, and argillaceous limestone locally altered to ""skarn"" or ""tactite"". The Laib limestone is overlain by black argillite and underlain by the Reno quartzite of Pre- cambrian age. Repetition of folded beds has allowed the interpretation of the large isoclinal fold which repeats the limestone (see general cross-section). Dolomitization and the associated lead-zinc ore have been found only in the right-side-up limestone and are not known in the overturned limestone.Two elongated stocks of granite cut the sediments. The Emerald stock outcrops along the east side of the Emerald tungsten mine and again west of the Jersey workings, while the Dodger stock outcrops only at the north end of the Iron Mountain. The shape and attitude of these bodies are believed to have been governed partly by pre-granite faulting and partly by pre-granite folding of the sediments. Although some forceful intrusion may have occurred the detailed granite surface indicates a gentle stoping emplacement."

Jan 1, 1949

By Jean-Paul Drolet

"The ultimate aim of the Law of the Sea Conference, held under the auspices of the United Nations, is to ensure that all aspects of the use of the sea are covered by international law. The question facing the nations of the world can be stated as: "" Who will control and benefit from the use and the wealth of the sea?""The United Nations Conference on Law of the Sea - known as UNCLOS - which reconvened in New York during the latter part of August 1978 was the third such Conference in the UN's history. The concepts of sovereignty over the territorial sea and freedom on the high seas have remained fundamental to the international law o f the sea until our time. The legal regime based on these two concepts developed initially from state practice meant that the unilateral actions taken by one or more countries were eventually accepted and followed by others.It was not until 1958, during the first Geneva Conference on the Law of the Sea (pursued in a second Conference in 1960) that the Law of the Sea was codified and modified to a certain extent by the then independent nations of the world in the four multilateral conventions on territorial sea and contiguous zone, continental shelf, high seas, and fishing and conservation of living resources.A third Conference got under way many years later when the members of the UN met in New York at the end of 1973 for preliminary discussions . This meeting stemmed largely from the need to fill gaps in existing international legislation which did not cover the new uses of the sea. The Conference was subsequently reconvened a number of times - in Caracas (1974), in Geneva (1975) and twice in New York (1976) for what was called "" substantive negotiating sessions."" A sixth session was held in New York in 1977; a seventh, held in Geneva at the beginning of 1978, recessed and reconvened in New York at the end of August 1978. This is what is referred to, in international jargon, as the seventh session of the Third United Nations Conference on the Law o f the Sea. The following dates are the principal markers of a saga which began some twenty years ago with the purpose of regulating the use of the oceans."

Jan 1, 1981

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By F W. Irwin

In recent years, a number of significant developments have occurred in the steel industry which are no-table and of general interest. This paper is confined to the steel-melting phase of the business. The development of high production rates on Stelco's Basic Open Hearth furnaces is chronologically summarized. Al-though various aspects of this subject have been presented previously, this paper summarizes the developments in high fuel rates, the usage of basic refractories, low and high oxygen rates and hearth maintenance. Background T HE interest which has been shown in steelmaking techniques in the past few years has been due, primarily, to the extremely high production rates obtained. Upon further study of the facilities and techniques employed to generate this steel at record rates, tonnage oxygen appears as the common factor. It can be stated that tonnage oxy-gen has revolutionized steelmaking techniques to a degree never before encountered. It was only about ten years ago that the use of large amounts of pure oxygen in a steelmaking

Jan 1, 1965

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By Zhou Yanwen, Fudong Wang, Shing Liu

Mixed CrB2 and MoS2 powder (Cr:Mo=1:1 atomic %), without any further process, were used as the targets to be sputtered and deposited onto stainless steel and silicon substrates by pulsed DC power supply. The structures and properties of the CrBMoS films were then analyzed by using SEM, XRD, micro-hardness tester. The SEM morphology of the films showed dense, defect free structure, and the preferred orientations of the films were CrB2 (111) and MoS2 (200) according to XRD spectra. The thicknesses of the films were measured and the relationship between the deposition rates and pulsed factors was determined. The films, with the micro-hardness as high as 19GPa and friction coefficient as low as 0.02, could be considered to be the hard solid lubricant films.

Jan 1, 2015

By David Green

"This paper describes Outokumpu's Tank Cell concept using the unit reactor principle and operating experience gained in various applications. Presently the tank cells used range in size from 35 t pilot size to 100 m' (3500 cuft). The paper discusses operating experience and results from commercial installations in copper and zinc rougher and cleaner services.The key feature of the Tank Cell described is the effective control of the froth phase and resulting possibility to operate on an improved grade recovery curve by manipulating the control variables."

Jan 1, 1995

By S. Dominguez, E. Gebrehiwot, S. Richardson, S. Sandoval

Copper electrowinning/electrorefining (EW/ER) is powered by direct current (DC) rectifiers that typically generate 30,000 to 70,000 amps and a bus-bus voltage of 200 to 500 volts DC. Tankhouses are designed so that DC current flows through “cell lines” which contain individual EW/ER cells electrically connected in series. Electrolyte composed of copper sulfate and sulfuric acid in water forms the “liquid conductor” that connects the metallic conductors in this circuit. In this setting, stray current is a DC current that strays from and therefore bypasses the tankhouse circuit by finding a path to ground, often through the electrolyte in pipelines that feed into and discharge from the cells, or through dried electrolyte (i.e. sulfate), which is also electrically conductive. Tankhouse workers can be exposed to shock hazards if they become part of a stray current path to ground. This presentation details examples of stray current shock hazards in electrolytic tankhouses and provides voltage and amperage measurements associated with stray current in these examples. A review of critical safety controls in EW/ER tankhouses that will mitigate the risk of employee shock from stray current is also provided. INTRODUCTION Electrolytic tankhouses are designed to deliver relatively large amperages of DC current to a series of electrolytic cells in which copper is plated out of solution using the classic anode-cathode pair geometry within each cell. Electrolyte is the “liquid conductor” that transfers current in between the metallic conductors of the cell. The metallic conductors include inter-cell copper bus bars and the anodes and cathodes themselves. It is sometimes forgotten that electrolyte as a conductor is capable of delivering DC current outside the designed circuit of a tankhouse. Stray current is a DC current that strays from the tankhouse electrical circuit by finding a path to follow other than the designed path. Safety becomes a concern when there is a risk of an employee becoming part of an accidental stray current path, thereby suffering an electrical shock. In 2016, Freeport-McMoRan (FMI) suffered a fatality at one of its copper electrowinning tankhouses. The forensic analysis concluded that stray current from the tankhouse rectifier contributed to the fatality. An employee accidentally fell into contact with a metal flange at the end of an HDPE pipe that was collecting cell overflow electrolyte from the tankhouse. DC current passed through the employee to ground, creating a shock that was judged to contribute to his death. The situation was exasperated because the employee was unconscious, and therefore was exposed to the stray current for several minutes before being found. In addition, the employee’s clothing was saturated with liquid, and the employee was found kneeling in puddled liquid on the ground. FMI immediately began an investigation into the root cause of the stray current that was measured at the scene. Sufficient electrolyte had accumulated in the HDPE pipe such that a continuous path was formed between it and electrolyte that was continuously overflowing from energized electrowinning cells. The metal flange on the pipe was the metallic conductor that carried the current to the employee from the electrolyte inside the pipe. Current then flowed through the employee to ground. Because of this incident, FMI undertook an extensive review of the hazards of stray current in EW/ER. FMI’s tankhouse workforce received a Tankhouse Electrical Safety training course developed in- house to insure worker understanding of stray current hazards. Tankhouse design changes were implemented to better insulate workers from stray current. Personal protective equipment (PPE) standards were also reviewed and changes made.

Jan 1, 2019

By J. Palarski

Hard coal, mined in Silesia Region as well as in the eastern part of Poland, is a key national resource. In Polish underground coal industry, modern mining technologies have been successfully tested and used in the last 50 years. More than 98% of the coal produced underground is extracted by longwall mining method. Current underground coal mining expands into increasing depths. The use of conventional coal extraction methods ? room and pillar and longwall with caving - is becoming increasingly difficult. The coal mining is modifying existing methods and is testing innovative technologies. Backfill is an important component of modern underground mining operations. In Polish underground mines, backfill is recognized as an integral component for extraction of coal from greater depths in a densely populated environment. The modifying and innovative methods require the use of backfill or grouting of caving to provide structural support in underground excavations and to ensure that the mining operations are safe. Depending on the geological structure, mining conditions and environmental requirements there are several variations of longwall methods used in underground coal mining in Poland, in particular: longwall with caving, longwall with backfill, longwall with grouting of caving area. This paper will discuss the different components of an effective longwall production and filling process of caving area. The paper will give a overview of the current application of backfill technology, focusing on Polish coal mining operations. This paper will also briefly describe how backfill contributes to an innovative method ? underground coal gasification. The paper discusses specific requirements for fill materials and the technology of backfilling for underground coal gasification (UCG) operations and problems of implementation and correlation of backfill parameters with other processes that occur during thermal processing of coal.

Aug 1, 2013

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016