Search Documents

By E. J. Marcotte

"BRIEF DESCRIPTION OF GRINDING CIRCUITCrushed ore at -5/ 16 in. is delivered by a conveyor system from the crushing plant to two 1250 ton fine ore bins. The ore is transferred from each bin by a 30 in. feeder conveyor belt, operated by a Link Belt P.I. V. (variable speed) drive, to a 24 in. conveyor that feeds the 8 x 10 Allis Chalmers rod mill.The rod mill discharges to a common mill discharge pump box. Three 6 x 6 SRL pumps are employed to pump the combined mill discharge pulp to a common distributor box which distributes the feed to two of the three Kreb D lSB cyclones in each of the two banks at a hydraulic pressure of 6 psi.The cyclone overflow at a specific gravity of 1. 25 (i.e. 32% solids) is transferred by gravity to two revolving chip screens for wood chip removal and from there to a pump box. Two 5 x 5 SRL pumps feed the pulp to the thickeners. The underflow from the cyclones is fed to two 8 x 8 Allis Chalmers ball mills which discharge to the common mill discharge pump box. Thus, a closed circuit is formed between the ball mills and their respective bank of cyclones. The circulating load as most recently calculated is 262%."

Jan 1, 1966

By M. T. Ho, D. E. Wiley

The iron and steel industry accounts for almost 5 % of the total world CO2 emissions. Optimisation of the steelmaking process has led to significant reductions in the energy intensity to the point where it is now close to the thermodynamic limit. Further reductions are not likely to be achieved with efficiency improvement alone and will require the development of novel or breakthrough technologies. This paper will show the costs of implementing CO2 capture at direct atmospheric emission points for a number of iron and steel production processes. These include a conventional process, top gas recycling processes, the Corex and Hismelt smelt reduction processes and the Midrex direct reduction process. Depending on the point source emission, costs of capture with existing chemical absorption technology at iron and steel plants can be similar to capturing CO2 at pulverised coal fired power plants.

Jan 1, 2015

By Hiwa Salimi, Foley. Stephen R, Loghman Moradi

Common water-miscible organic solvents including DMSO, DMF, methanol, ethanol, acetone and THF in combination with HCl and low concentrations of H2O2 were investigated for dissolution of gold. THF showed the best result demonstrating that gold powder could be completely dissolved in 1.5 hours in 1.0 mol/L HCl and 0.2 mol/L H2O2. No complete gold dissolution was observed for the rest of solvents even after 24 hours. The rate of gold dissolution was measured by dissolving gold wire in THF/HCl/H2O2 mixture. The rate of gold dissolution in optimised condition was 75 g m-2 h-1 at room temperature and significantly increased to 590 g m-2 h-1 by raising the temperature up to 60 oC. Although a THF/HCl/H2O2 mixture showed a slower dissolution rate in comparison with aqua regia, however the applied conditions are considerably milder which is highly promising for gold leaching in an industrial scale.

Jan 1, 2015

By S. Avalos, J. M. Ortiz, W. Kracht

Semi-autogenous grinding mills are intensive energy consumers. Current models base their energy consumption inference on operational variables and feeding ore characterization. While they provide adequate design guidelines, they are not suitable for real-time energy forecasting dealing with gaps in operational dataset and up/downstream process bottlenecks. This work explores the capability of Gated Recurrent Units to learn the semi-autogenous grinding mill consumption behaviour. Gated Recurrent Units are trained to forecast different time-support consumptions under a time-series operational dataset. The results show high performance on small supports (30 minutes) to capture local variability and long-trends while larger time supports (8 hours) can only capture time-trends but not local variability. The proposed technique seems promising for further research and implementation on real mine cases since the input variables are low-cost and easy to obtain. INTRODUCTION Current changes in the Chilean energy matrix (Román-Collado, Ordoñez, & Mundaca, 2018), from fossil fuels to renewable energies, have impacted different industries and particularly the mining sector. Solar energy incorporation into greenfield/brownfield projects will help reducing costs and will lead to rethink foundational paradigms (production and processing strategies) (Pamparana et al., 2017). Also, integration of new space-time predicting tools together with automated real-time updating models are some of the main challenges in the geometallurgical framework (Ortiz et al., 2015; van den Boogaart & Tolosana-Delgado, 2018). Those contexts encourage and demand the development of tools capable of predicting the energy consumed by mining systems, being comminution the greatest energy consumer with an average close to 50% of the entire mine consumption (Cochilco, 2013). In comminution, the semi-autogenous grinding mill (SAG) represents the largest energy consumer (~10 nominal each SAG). Theoretical and empirical energy consumption models (Jnr & Morrell, 1995; Morrell, 2004; Silva & Casali, 2015) base their inferences mainly on feed/product size distributions, SAG sizing, bearing pressure, feed hardness, water addition and grinding charge level, and commonly assume steady-state and work isolated from up and downstream processes. While those techniques provide adequate design guidelines, they are not suitable to predict hourly, daily or even weekly energy consumptions on interconnected comminution circuits where upstream/downstream bottlenecks lead SAGs to operate below designed regimes. Forecasting energy consumption is required by short-term energy management, medium and long-term planning energy consumption, designing the nominal capacity of renewable energy sources, among other. Also, when models are input-sensitive and some of those input measurements are expensive and/or time consuming, model robustness suffers when real-time predictions are required.

Jan 1, 2019

By G. Labonté, J. Truskoski, A. Kerr, A. Bouchard, J. Barrett

"Improving mill grade recovery relationships is always good business. Inco’s Clarabelle mill has just undergone a $16 M process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Project team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as Inco embarks on its second century of operation. IntroductionIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at Inco’s Clarabelle mill in Copper Cliff, Ontario."

Jan 1, 2003

By T. M. Siew

"This paper begins with a brief discussion of the geology of the Newfoundland Zinc Mine area. The results of groundwater studies and pumping tests are then presented. It was decided that groundwater in the mine could best be controlled by conventional sump pumping and grouting. The system is fully described, as well as plans for improvements on the method. LocationThe Newfoundland Zinc Mine is located in the Great Northern Peninsula of Newfoundland, six miles northeast of Daniel's Harbour. The mine is situated at an elevation of approximately 350 feet above sea level, 5 miles farther inland , west of the long range of mountains which rise abruptly with elevations of over 2,000 feet above sea level.GeologyThe ore deposits occur in lower Ordovician carbonate rocks that form part of the stable St. Lawrence platform, which is mainly composed of (1) the lower Cambrian Labrador group, (2) the upper Cambrian to lower Ordovician St. George group, (3) the disconformity overlying Middle Ordovician limestones and shales of the Table Head formation and, (4) two overlying klippen composed of Cambrian and lower Ordovician rocks.The ore deposit is a Mississippi Valley type of the Tennessee variety, having proven are reserves of 5.3 million tons averaging 9.70/0 zinc from eleven ore zones which exist in an area of 5.5 square miles.Among these ore zones, the L zone is the major underground mining area, and is by far the largest of the known deposits. It has proven are reserves of 3.4 million tons with 11.5% zinc; this underground development has been inprogress since 1974.Stratigraphically, the orebody, which occurs about 300 feet below the disconformities between the Table Head and St. George formations, is situated in the upper St. George formationof lower Ordovician age.The upper St. George formation of the L zone is divided into three main units (Fig . I) : the underlying lower limestone the middle grey dolomite pseudo breccia unit and the overlying siliceous dolomite unit. In this area of the mine, the beds of the St. George formation dip gently west to northwest to 10 to 15 degrees. The orebody, which is generally strata controlled with a southwesterly plunge and which has the form of thin, narrow, but elongate, en-echelon ore bed s, is contained in grey dolomite pseudo breccia. Its dimensions vary from 50 to 900 feet in width and 8 to 120 feet in thickness, and the over-alllength exceed s 6,000 feet.The surficial deposit of the area is a till comprising a heterogeneous mixture of sand, gravel, cobbles and boulders, with an average depth of 20 feet."

Jan 1, 1980

By F. Osmond, R. Kelly

"Malcolm Knowles, the famous adult educator once wrote: ""What a challenge we in human resources development face if we are to avoid the obsolescence of our workforce. I can foresee this challenge requiring that we reconceptualize (...) and redefine the role of HRD, away from that of managing the logistics of conducting training activities to that of managing a system of learning resources"".The context in which this was written surrounds the subject of adult education and the need for business and industry to change its approach to the treatment of adults as learners. In explaining what 'managing a system of learning resources' means, Knowles refers to line supervisors and managers as the most ubiquitous resources for day-in and day-out employee development. In many organizations training has been largely a staff rather than line responsibility. Even where trainers reported to line management, it was still seen as a staff function performed by a few specialists.This change referred to by Knowles places a much heavier responsibility on line supervisors and managers for the development of their personnel than has traditionally been the case. Managing that change - handing over the responsibility to the line organization - is the supreme challenge for the HRD function.Just why is this change necessary? Because too often, the learner does not effectively use on the job what he or she learned in the classroom. In fact, learners often discard new methods and revert to the older ways. The reason training does not stick is that the systems for training and work management are most often separate entities and while one may support the other, they need to be a single integrated system in order to ensure the transfer to the job effectiveness of training and some real value for the training dollars.Because much training can be wasted, steps have to be taken to ensure that it fulfills its intended purpose. The effective and continuing application of knowledge and skills that learners acquire can only be realized when line supervisors and managers are at the centre of the training system.This paper describes how such a systemis being developed at the Iron Ore Company of Canada (IOC) as a functional training program is introduced. The following text provides background information on the IOC - who they are and where they are located, a definition of functional training, an evaluation of the suitability of this approach for adults in industry, a description of how the program is being implemented at IOC and some observations that have been made as this change is experienced."

Jan 1, 1995

By Göckmann. Klau

"IntroductionCopper has been recycled ever since its discovery. Even in Graeco-Roman times recycling of this resistant, and thus valuable material was carried out as a matter of course. Just take, as an early example, the Colossus of Rhodes: after the figure collapsed during an earthquake, the bronze parts were melted down into ingots and sold.Copper is a material which can be recycled again and again because copper produced from recycling is not different from copper originating from primary materials. This is mainly due to electrolytical copper refining whereby not only the base metals but also the precious metals can be removed. In contrast, with aluminum and iron only the more electropositive elements can be removed by refining, and the resultant scrap must, therefore, be sorted mechanically into various alloys for subsequent smelting.The recycling rate for different base metals is given in Table 1. Despite this ideal prerequisite, the generally quoted recycling rate of copper of about 40070 appears rather low. However, it must not be forgotten that the recycling rate is defined as the ratio of the annually utilized quantities of copper scrap and the annual production figures (Table 2). Moreover due to the economic growth over the last 30 years the availability of copper from scrap materials is lower than its consumption because copper is principally employed in very long-life consumer durables and only returns to the recycling circuit after many years. The average time for the copper of some goods to be recycled is detailed in Figure 1."

Jan 1, 1992

By Michael Samis

NOFLEX valuation results ? CF deviations and net CF risk discount factors ??Cash flow deviations indicate average cash flow variability. ??Net cash flow riskdiscount factors (NCFRDFs) indicate the size of the risk adjustment applied to a cash flow. NCFRDFs profile should change with variations in cash flow uncertainty since the risk adjustments applied to the project cash flow reflect investor sensitivity to uncertainty.?DCF and RO will often produce different NCFRDFs for the same project since they use different methods of risk-adjustment.

May 1, 2006

By Peter Harben

"This paper discusses the benefits of industrial minerals, their sources of supply, price and marketing trends, and their increasing use as substitute materials and ""strategic"" minerals. IntroductionKaolin finds have yet to spark the kind of frenzy associated with the 1849 California gold rush; no dolomite deposit has ever gained the notoriety of the Comstock Lode; and few industrial minerals are counted among the currently fashionable list of "" strategic mineral s"". Nevertheless, the glamorous zhine associated with metals may be somewhat superficial; further digging provides perhaps the real foundation of modern society - industrial minerals.They are often tagged as common, everyday materials that are simply dug out of the ground, crushed and hauled to a local point of consumption. Although this description is accurate in the case of road aggregates, sand and gravel, and the like, there are many exceptions to this rule. The term industrial minerals is rather nebulous, covering as it does the mundane and esoteric, the chemically active and the refractory, the $2 and the $10m-a-ton product. All of these minerals influence every facet of modern life from fertilizers to fire retardants, ceramics to cars, construction to clothes, and toothpaste to tennis courts. Their usefulness is well illustrated by the variety of industries they serve; the main ones are listed in Table 1. It is now time to dismiss the notion of non-metallics as the ""third world"" of natural resources business after the metallic and energy products by dispelling some of the myths regarding abundance, variety and value of the group's sixty-plus products."

Jan 1, 1982

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By G. Vibert Douglas

NICKEL minerals are known in New Brunswick but have never been reported from Nova Scotia. The attention of the writers was drawn to an occurrence of pyrrhotite, reported to carry nickel, at the Second Gold brook, Middle river, Cape Breton. The purpose of this paper is to record the occurrence and give an account of the general geological association. In a later paper it may be possible to give greater details? than are available at present. GEOLOGY The area lies at the edge of a plateau of Precambrian rocks which forms the panhandle of Cape Breton island. This plateau has a general elevation of 1,200 feet. Middle river, with its tributaries, the First, Second, and Third Gold brooks drains the area. The lower country to east and southeast of the plateau is underlain by lower Carboniferous sediments. The rocks of the plateau are presumably of Precambrian age but have never been definitely correlated with the Gold-Bearing Series of the mainland. ?There i:s; however, some resemblance, although they have apparently been more intensely mountain-built. They are essentially fine grained, sheared quartzites and slates . The general strike is east and west, with a north dip of 45° to 55°. There are smalllocal drag-folds in the area. The only igneous rock in the immediate vicinity is an intrusive pink porphyry. It has small phenocrysts of quartz and feldspar. It has intruded the sediments generally along the structural planes, but in places crosses the structure . Its intrusive character is further proved by the fact that it contains xenoliths of the quartzite.

Jan 1, 1937

By Jacek Paraszczak, Stefan Planeta

"RésuméDans la première partie de cet article on discute Ie contexte technico-économique de l'usage des foreuses à l'eau sur béquille dans des mines sud-africaines. Par la suite on présente les résultats d'une étude comparative du forage avec les foreuses à l'huile et à l'eau par rapport aux foreuses pneumatiques. La performance des foreuses est discutée sous les deux aspects: l'aspect technique concernant Ie taux de pénetration et la quantité d'eau rejetee dans les galeries et l'aspect de fa santé et sécurité au travail, et plus particuliérement, les niveaux de bruit et de vibrations ainsi que Ie brouillard de l'huile. On conclut par l'évaluation du potentiel de forage à I'aide des foreuses hydrauliques dans Ie contexte canadien.AbstractIn the first part of this paper the technical and economical aspects of water-powered drilling are discussed. This technology, originally employed in South Africa, received some interest from Canadian mine operators. In this context a comparative experimental study of pneumatic and hydraulic (oil- and water-powered) jackleg drills has been realized. The performance of the drills is compared and the results reviewed with regards to technical aspects (penetration rate, amount of water spilled) as well as health and safety considerations (noise and vibration level, presence of oil mist). The potential for application of hydraulic jackleg drill is discussed."

Jan 1, 1995

By P. E. Davidson

The management of solid waste is known to be a large and increasing problem in high-population areas throughout the world. It is not necessary here to add further definition to the nature and magnitude of the problem. Instead, it is the purpose of this paper to describe a new process, called the Andco-Torrax System, which will be of use in converting municipal solid waste into useful energy forms and a granulated slag by-product. The paper includes a description of the first commercial plant for the process.

Jan 1, 1977

By R. Guimarães, L. Silva, J. Milboume

The São Bento concentrator was built by Gencor in 1985 to treat refractory gold-bearing flotation concentrate. The plant was the first commercial application of pressure oxidation for refractory gold ore following about a year after the first use of pressure oxidation on a whole ore at Homestake's McLaughlin operation in California. Ore from the Sao Bento mine is remarkably consistent in gold grade and arsenic and sulphide concentration as is typical in banded iron formations (BIF) (l). Gold content is approximately 9 g/t with approximately 30 - 40% free milling. The balance is associated with arsenopyrite and pyrrhotite. An expansion of both process facility and mine was undertaken between 1996 and 1998, raising the treatment capacity from 32,000 t/mo to 45,000 t/mo.

Jan 1, 2004

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By Pierre St-Julien, Réjean Hebert, M. Racine, Roch Gaudreau, Pierre Lacoste, Michel Rocheleau

"Les unités volcano-sédimentaires de la ceinture de l'Abitibi à l’est de Val-d' Or ont été regroupées en quatre domaines litho tectoniques. Du nord vers le sud, nous reconnaissons les domaines d'Assup, de Garden lsland de Val-d' Or, de Trivio et de Villebon. Deux de ces domaines (Garden Island et Trivio) correspondent à des couloirs de déformation, d’envergure régionale et d’orientation approximative E-W. Les trois autres domaines sont caractérises par des volcanites defond océanique de type MORB (tholéiites et komatiites) qui sont en position inferieure; ces volcanites sont surmontées par des sédiments marins de type turbidite (domaine de Ville bon) ou évoluent dans le temps, soit vers un volcanisme bimodal d'affinités tholéiitique et calco-alcaline ( domaine d'Assup), soit vers un volcanisme d'arc insulaire (domaine de Val-d'Or). Il n'existe aucune certitude de corrélation litho stratigraphique entre les différents domaines et l'on doit considérer la possibilité que ceux-ci représentent l'accolage tectonique de terranes de nature et d'origine différente.Les principales caractéristiques structurales de la région sont regroupées en quatre étapes de déformation dont trois sont archéennes et la quatrième attribuée à l'orogenèse grenvillienne. Au moins cinq facies métamorphiques ont été reconnus: I) un facies régional faible propre à la province du Supérieur, 2) un facies de cornéennes a amphibole en périphérie du pluton de Pershing, 3) un facies hydrothermal dans la zone tectonique de Cadillac, 4) un facies régional moyen dans la zone de bordure de la province de Grenville, et 5) un facies régional élevé a l'intérieur de la zone structurale du front de Grenville.Le front de Grenville est défini dans la région par l’apparition subite des ortho gneiss au faciès métamorphique élevé et par la disparition du grain tectonique E-W. Le contact brusque entre les deux provinces pourrait correspondre à une zone de chevauchement de la province de Grenville sur la province du Supérieur. La région étudiée est l’hôte d’un gite majeur de sulfures massifs et de plusieurs gites et indices aurifères; elle présente des cibles favorables pour l’exploration minière dans le contexte tectonométa-morphique de l'influence grenvillienne. L'intérêt de la Formation de Val-d' Or pour les métaux de base et le potentiel aurifère des couloirs de déformation d'orientation approximative E-W, sont bien connus. Les structures grenvilliennes NE-SW, qui se développent vers l'est, représentent aussi des cibles intéressantes, en particulier dans les secteurs ou elles intersectent des cisaillements E-W kénoriens."

Jan 1, 1990

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014