Search Documents

By Werner W. Scholz

A corrosion-resistant lining is, quite often, selected on the merits of its corrosion resistance only. This paper demonstrates the effects of temperature, pressure, weather, design aspects and variances of physical properties within the scope of the generic designation of a corrosion-resistant material or materials. The base for the study is a rubber- and brick-lined steel vessel, with unchanged chemical conditions. Graphs and sketches illustrate the various effects of physical influences on the selected lining specifications.

Jan 1, 1979

By Li Xibing

The In order to mine safely with reasonable cost, it is necessary to research the fracture characters of backfill and its matches with rock mass. Four kinds backfill with cement-tailing ratio of 0.250, 0.125, 0.100 and 0.083 respectively were tested, and basing on stress-strain curves tested, the deformation characters and fracture laws as well as the damage constitutive equations investigated with damage mechanics whose calculating results are coincided with experiment results well were proposed. The results of damage analysis show that there have different damage characters in different backfill, e. g. the lower the ratio of cement to tailings the lower the damage values when stresses reach to peak value; the lower the content of cement the more rapid in damage and the more abrupt in breakage process. In addition, using catastrophe theory, an energy model was proposed for backfill and rock mass acted each other in mechanics, and the unstable condition of the system was obtained. Research results show that the higher is the stiffness of rock mass the more stable the system, and the lower is the ratio of cement to tailings, the more unstable the system will be. Further more, according to the catastrophe model proposed, the reasonable matches between backfill and rock mass were researched, and a calculation formula that designs reasonable strength of backfill during mining was put forward. It has been proved by practice that the model and theory researched in this paper can guide filling design in mining. Keywords: Cemented tailings backfill, constitutive equation, catastrophe theory, match of backfill and rock mass

May 1, 2007

By Dirk van Zyl

The world is consuming more and more electronic products every year. This has caused a dangerous explosion in electronic scrap (e-waste) containing toxic chemicals and heavy metals that cannot be disposed of or recycled safely. But this problem can be avoided. We are pressing leading electronic companies to change; to turn back the toxic tide of e-waste. Every year, hundreds of thousands of old computers and mobile phones are dumped in landfills or burned in smelters. Thousands more are exported, often illegally, from the Europe, US, Japan and other industrialized countries, to Asia. There, workers at scrap yards, some of whom are children, are exposed to a cocktail of toxic chemicals and poisons.

May 1, 2008

By D. G. Ingram

This paper reviews the operating and maintenance practices at Bethlehem Copper from the commencement of operations in November 1962 to the present. Cost data and wear life of major components are also discussed.

Jan 1, 1979

By J. L. Collins

"This paper deals with the quantitative analysis of mine maintenance records. Based on a case study of dozer engine records, the author suggests an easy method of deriving useful information for managerial decisions in a step-by-step manner.More specifically, the paper deals with the following topics:• determination of the most economical replacement time,• determination of reliability characteristics,• determination of the number of replacements, and• determination of the number of spares.IntroductionThe mining industry collects a lot of information about every aspect of its activities, an example of which appears in Table I. In Table I , the distribution describes the operating hours at failure of 56 different dozer engines used in severe applications. Besides calculating an average and possibly a standard derivation from the data, little else is derived, at least from a statistical point-of-view.More information can be obtained from these records that could help management in the decision-making process.To illustrate this point, the sample data appearing in Table I will be analyzed in detail by making use of well-known concepts in reliability engineering.Distribution of DataTable I represents a distribution obtained from the recorded hours cumulated from the operators' time cards. The operating hours have been divided into fourteen classes for each 1000 hours of engine running, e.g . all engines scoring an operating time of between 1001 and 2000 hours formed a class , those scoring between 2001 and 3000 hours another one, etc. Generally, the class interval should be a multiple of the equipment preventive maintenance check period.The minimum acceptable sample size should be large enough to ensure that the score in each class interval is at least one. Ideally, the score for each class interval should be at least five so that a chi-square test could be carried out if necessary.The average life of an engine can be found by adding the products of the frequency and the class mark (mid-point) values. Therefore:"

Jan 1, 1987

By A. Tohn, K. Adham, R. Lu, D. Lemieux

"To remove sulphur, carbon and arsenic from the gold concentrates of Dundee Sustainable Technologies (DST), Hatch has designed a demonstration plant roaster using the fluid bed technology. The fluid bed was selected for its ability to maintain stable temperatures and uniform reaction conditions. Data points from a small pilot plant (operated by DST) were used for setting the parameters of the demo plant roaster.The DST demonstration plant is being built to further prove their patented gold extraction process at an industrial scale. Their gold extraction process is based on halogenation at atmospheric pressure and relatively low temperatures. Before the halogen leaching, most of the sulphur, carbon and arsenic should be roasted out of the feed concentrate.The Hatch fluid bed roaster design includes a moist feed introduction system, simple bed cooling for temperature control, and cyclone fines recirculation. The demonstration plant roaster is planned for construction in 2014, and the performance results will be presented in a future paper."

Jan 1, 2014

By Dale A. Sketchley

"Abstract - Large differences in gold content between rock fragments or small volumes of unbroken rock, commonly referred to as the nugget effect, are related to sample and subsample weights, crushing and pulverizing sizes, and density, shape and size distribution of gold grains. Gy’s sampling theory, which relates gold grain characteristics to sample weight, fragment size, and error, provides a method of estimating a sampling constant that quantifies deposit characteristics that contribute to the nugget effect.Sampling control tests provide methods for determining the sampling constant. Sampling control charts, comprising nomographs that relate sample weight, error and particle size, use the sampling constant to optimize sample weights and comminution sizes, and to minimize the variability introduced by incorrect or inadequate sampling and sub-sampling procedures. The sampling constant is useful in classifying ores into arbitrary categories according to expected sampling difficulties. Spatial variations in the sampling constant can be used to aid in defining ore types for modeling geological domains, which should have unique sampling protocols. Examples that illustrate the relationship between the sampling constant and expected sampling problems, and the spatial variation of the sampling constant, are given for various deposits. Case histories of sampling programs are presented.Quality control procedures consist of monitoring sample contamination amd accuracy and precision of analytical results. Accuracy, precision and contamination are monitored by including standards, duplicates and blanks into batches of samples being analyzed. Analytical results of standards and blanks are plotted on a batch-and-time basis with control lines at plus or minus two/three standard deviations as confidence limits of the accepted round-robin value. Examples are given that illustrate a laboratory system in statistical control and the various types of problems encountered when interpreting quality control data. These include sample transcription errors, degradation, contamination, sampling errors, detection limit problems, instrumental drift, lack of statistical control, laboratory bias, procedural problems and data tampering.Where bias is negligible, precision, as a function of concentration, can be obtained from duplicates using the Thompson-Howarth precision algorithm, which also allows calculation of the practical detection limit. Examples are given that illustrate variations in precision, with grain size, for different types of duplicates, as well as mineralogical changes and sampling errors."

Jan 1, 1998

By Tedd E. Lister, Andre Anderko, Peiming Wang

Mobile electronic devices such as smart phones and tablets are a significant source of valuable metals that should be recycled. Value metals in phones are gold, palladium, silver, copper, cobalt and nickel. Devices now contain increasing amounts of rare earth elements (REE). Effective recycling schemes should include the recovery of these critical materials. Targeted recycling of items containing more of the less available critical materials could address their future criticality. This presentation will describe an electro-hydrometallurgy approach to efficient recycling of metals from scrap mobile electronics. The electrorecycling (ER) process generates oxidizing agents at an anode while reducing dissolved metals at the cathode. Development of the process involved generation of E vs pH diagrams, complemented with metals dissolution experiments used to assess the effectiveness of various solution chemistries. Although several schemes were envisioned, a two stage process has been the focus of work: 1) initial dissolution of Cu, Sn, Ag and magnet materials using Fe+3 generated in acidic sulfate and 2) final dissolution of Pd and Au using Cl2 generated in an HCl solution. Results from laboratory work will be discussed.

Jan 1, 2014

By Marc Bétournay

This article examines how fuel cell technology and related power distribution system fits within mine operating requirements. Considerations for improvement of power plant architecture and functions to yield production advantages are presented. Improvements to conventional mining approaches are also discussed.

May 1, 2007

By T. Navessin

Recent research activities in proton exchange membrane fuel cell (PEMFC) have significantly improved the performance per unit cost and its lifetime. These activities narrow the technology gaps, and thus, enable commercialization in some applications. One particular focus is in the development and understanding of proton conducting membrane materials. Many novel membranes are being developed which provide control and systematic understanding of complex relationships between chemical structure, morphology, physicochemical properties, and electrochemical kinetics. In this study, different classes of proton conducting membranes suitable for portable and automotive applications were evaluated in an operating PEMFC at the Institute for Fuel Cell Innovation, National Research Council. Analysis of these results may provide constructive feedbacks to the material researchers.

Jan 1, 2005

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By B. Vorobyov

A Canadian company, Sight Power Inc., has developed a revolutionary, fully automated shaft monitoring and inspection system for deep-level mining based on a 3D mobile laser scanning technology. It consists of a special hardware unit and proprietary software with Artificial Intelligence elements for object recognition, features identification and change detection. The main purpose of this system is to significantly improve the safety of underground mining as well as to increase the available hoisting time thus generating substantial additional revenue for the mine.

Aug 1, 2013

By M. Hawker, M. Kreuh

The mining and metallurgy industry is known to be of cyclical nature associated with price volatility. As such, some years are quite lucrative and other years require mining companies to tighten their belts. The field is a mix of junior, mid-tier, and major mining companies. One thing that is common to all of them is the time required and the cost to develop a flowsheet in accordance with best practices. Although a long list of factors can impact flowsheet development, this paper will include the impacts of: experienced metallurgical engineers and laboratories, representative samples for high quality and valuable testwork results, and following engineering development stages. The paper also provides typical time frames to complete selected engineering flowsheet development steps.

Jan 1, 2014

By J. K. Van Beek

The Deep Underground Science and Engineering Laboratory (DUSEL) is a scientific facility that will be placed in the deeper reaches of the Homestake mine, Lead, SD. Our team of geologists and engineers is carrying out the first scientific project awarded to the site ? Towards a Transparent Earth. Taking advantage of the thousands of open exploratory and sand-line holes, we are installing the beginnings of a seismic observatory. Each installed station consists of a 3-D accelerometer package and a 1 nanoradian 2-D tilt meter. In order to allow for a variety of monitoring and characterization studies, the array instruments are sensitive over the frequency bandwidth of 0.2 - 1 KHz. Three, three component accelerometer stations are currently installed ? in a 140 m deep bore beneath the slurry pump house, and in 12 m deep bores on the 2000-foot level, 800 and 400 m from the Ross shaft. There is a tilt-meter installed at each 2000 level station. These installations are in 150 mm diameter sand-holes. From the currently installed tilt sensors we are investigating solid earth deformation as a response to tidal potential. The accelerometers are being used to locate and characterize events associated with mine dewatering and rehabilitation.

May 1, 2009

Post--Crunch Financial Management -An Overview A. The Industry and the Capital Markets B. .The SME -De-risking the Current and New Assets Followed by: C. The Lender?s Perspective on Re-financing?Jeff Stufsky, BNPParibas, NYCD D. .The Agency/Export Credit Lender Perspective?Doug Macaulay, EDC, Ottawa E. The Foreign Political Insurance Perspective?Pierre Vieillescazes, Carrick-Bend, Washington, DC ?Four Fundamental Metal Models No Longer Prevail. ?Mining is in new ?waters?: so be prepared (next page). ?Capital markets are uncertain-so be your own financier first ?If tight capital may remain, prepare to triage based on cash-flow production (not oz, lbs, tonnes, etc) ?Know your banker/financier(and it should know mining) ?In the past, it was ?know your borrower? ?The climbing team can fall if one climber carries too much ?Constantly re-assess the risk matrix (and j/v?s), and ?De-risk/diversify both the asset and the capital base

May 1, 2010

By E. A. Cleveland

A glance at the map discloses the fact that the Pacific Great Eastern railway either traverses or crosses some of the most important rivers of the province: the Squamish with its branches the Stawamus, Mamquam and Cheakamus; and the Green, Lillooet, Birkenhead, Fraser and Quesnel rivers. Each of these and some of their tributary streams, having their ?sources and upper reaches in the higher altitudes in regions of abundant snowfall, is capable in greater or less degree of furnishing water under suitable heads for the economic production of power. Beginning at its present terminus at Squamish the railway has the only hydro-electric development within its territory among the whole list of streams mentioned. A 225 horsepower installation at the edge of the East branch of the Squamish river, using water from Stawamus river, a branch of the former, under a head of 418 feet, is a modest beginning. Two or three additional sites, where water may be used under somewhat similar heads, may be found on this little stream. Next above Squamish, along the route of the railway, is the Mamquam, a long tributary of the Squamish from the eastern slopes. It has a drainage area of something like 130 square miles with widely varying discharges of from less than 50 to about 14,000 cubic feet per second. The preliminary investigations so far have disclosed no suitable storage sites, so the Mamquam may be regarded as a small continuous power stream - probably less than 1000 horsepower.

Jan 1, 1925

By Patrick J. Williams

Defining Features of IOCGs ? Sulphur-poor Cu-Au(-Fe) deposits ? Contain low-Ti iron oxides ? Hydrothermal origin (breccia, vein, replacement) ? Local structural controls (no ?causitive? intrusions) Common Features (Economically-Significant Terranes) ? Regional space-time association with plutons ? Association with widely metasomatized crust ? Na ? Na-Ca ? K ? Variable enrichment in F, Co, Ba, LREE, U ? Little hydrothermal quartz (cf. porphyry deposits)

May 1, 2006

By M. G. Lipsett

General Challenges for Mining & Mineral Processing Operations ? Capital-intensive industry ? Ongoing cost pressures ? Remote locations ? Workforce demographics ? Dynamic, unstructured, rugged environment

May 1, 2008