Search Documents

By E. W. Parsons

Permanent support of the back is an important economic factor in maintaining a tunnel or other underground opening in condition to render the service for which it was driven. Timber has been most commonly used for support in tunneling and drifting because of its strength and ease of installation. Even when treated for decay, however, timber is subject to deterioration and, over a long period of time, should not be considered a permanent support. Concrete support or lining is permanent and has been used in tunnels of every size for many years but has been almost exclusively cast in place, a difficult, costly process. This report deals with the design and installation of precast concrete supports to combine the best features of both methods.

Jan 1, 1958

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flat jack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the support elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 2010

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By D. Harrington

While apparently the hysteria with regard to silicosis and other occupational diseases has largely subsided and this subject is being more carefully considered and soberly judged, it would be poor policy for any employer to maintain that the storm has ended and that he can relax and revert to conditions as they were 5, 10, or more years ago. The fact is that the plan of paying occupational-disease compensation is now in its infancy and can be expected to grow rapidly. At present, while all of the States of the Union, including the District of Columbia and excepting only Arkansas and Mississippi, have compensation acts, only the following make provision for occupational diseases to some extent or in one way or another: California, Delaware, Connecticut, District of Columbia? Illinois, Indiana, Kentucky, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Jersey, New York, North Carolina, North Dakota, Ohio, Pennsylvania, Rhode Island, Washington, West Virginia, and Wisconsin. Silicosis is compensable in one way or another in California, Connecticut, District of Columbia, Illinois, Kentucky, Massachusetts, Missouri, New York, North Carolina, North Dakota, Ohio, Pennsylvania, West Virginia, and Wisconsin, and possibly in other States. During the past few months, occupational-disease legislation (largely silicosis) has been considered in some form in Arkansas, California, Delaware, Idaho, Maryland, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah and Washington. It will be surprising if comparatively comprehensive occupational-disease legislation is not on the statute books of nearly every State in the Union within the next 5 years. With this situation confronting him, the farsighted industrialist who has the interest of his organization at heart, if he has not already done so will immediately start to "put his house in order" by studying possible occupational disease hazards to his employees and promptly applying known remedial measures or attempting to devise such measures if none exist. Unquestionably, one of the most important of the surveys to be made relates to dust occurrence, as State laws on occupational disease are almost certain to contain provisions, on silicosis and, with almost equal certainty, the provisions of any State law are not likely to be particularly similar to those of other States.

Jan 1, 1938

By E. J. Lintner, J. R. Thoenen

During the period 1937-40 and until peacetime research was superseded in 1941 by wartime activities , the junior author was engaged in studies regarding the relative efficiency of operating methods in quarries producing crushed stone for mineral aggregates . The results of some of these studies were published as reports of investigations in 1939 and 1940 ; / others were discontinued due to war demands on personnel and time . The published reports discussed the efficiency of particular quarry operations with respect to the time consumed and without reference to costs or mechanical factors . • At the time , the field data were collected for the published reports other data were collected relative to the relationship of the numerous variable factors inherent in the operation of a churn drill to the ability of the drill to produce blast holes . The churn drill is essentially a crusher and depends. for its performance upon the foot-pounds of energy it can impart to the cutting edge of its bit . The gravity stamp mill , so well-known in western gold mines , is essentially the same type of crusher . The ratio of foot- pounds necessary to crush the rock , to the total theoretical energy developed by the falling churn- drill tools , affords a good means of evaluating the efficiency of the tool . This does not include to tal over-all efficiency involving the mechanical equipment of the drill itself or its power unit .

Jan 1, 1947

By J. B. Zink

The Bureau of Mines developed a spectrochemical method to determine six constituents in coal ash in the following concentration ranges: silica 9 to 63 percent, alumina 7.5 to 35 percent, ferric oxide 2 to 30 percent, calcium oxide 1 to 29 percent, magnesium oxide 0.5 to 6 percent, and titanium oxide 0.5 to 4 percent. Samples of coal ash are fused with a mixture of lithium tetraborate and vanadium pentoxide. The resulting beads are crushed, mixed with powdered graphite, and briquetted. The pellets are analyzed spectrographically, using controlled high-voltage spark excitation. Vanadium serves as the internal standard. Effects due to matrix variations are minimized by fusion with lithium tetraborate. Intensity ratios of selected analytical lines are determined photometrically, Concentrations are read from analytical curves, prepared from synthetic standards, relating log intensity ratios to log concentration. A combustion procedure is used to determine sulfur tri-oxide. The method is most useful when large numbers of coal ashes must be analyzed but a high degree of accuracy is not essential.

Jan 1, 1967

By V. F. Parry, J. B. Goodman, W. S. Landers

"This investigation was conducted: under the direction of A.C. Fieldner, chief, Fuel and Explosives Branch, Bureau of Mines, Washington, D. C. The following members of a Technical .advisory Committee were helpful in advancing the investigation: L. C. Harrington, dean, College of Engineering, University of North Dakota; D. F. Pane, president, Sheridan-Wyoming Coal Co.; Carson W. Smith, president, Consolidated goal & Coke Co.; Durbin van Law, consulting, engineer, Denver & Rio Grande Western Railroad; and C. B. Carpenter, professor of metallurgy, Colorado School of Mines. Coal samples from the Northern Colorado field used in the stoker during 3 years of service were supplied through the cooperation of N. C. Brooks, secretary, Northern Colorado Coals, Inc.This report describes the development and practical tests made on a small stoker-fired system for heating service water automatically. The system was designed to take advantage of the favorable reactivity of low-rank fuels, and the objective was to devise a combination of stoker, heat-receiving, and hot-water storage system Which would be automatic for at least 30 days without attention, while heating service water at minimum cost. The system was developed to a point where coal consumption was less than 10 pounds (or less than 100,000 B.t.u.) per day. The total operating cost of hot water for an average-family-was about $1.00 per month, with coal retailing at $6.00 per ton and electric power at 4 cents a kilowatt-hour. The heating system was designed for the utilization of low-rank fuels, but the general features of the double-tank system can be 'employed fuels, either gas or liquid fuels.The Subbituminous Coal and Lignite Section of the Bureau of Mines began investigations on the utilization of low-rank fuels in domestic appliances during 1939. Tests were made on various devices to find out if they were suitable for the low-rank fuels. Most of the available appliances for burning coal have been designed for the higher-rank fuels, and they are not well-suited for burning the lower-rank coals at maximum efficiency, because subbituminous coals and lignite have high bed moisture ranging between 20 and 40 percent by weight, which lowers heating value to the range of 10,000 to 6,500 B.t.u. per pound. They are noncoking, and the ash content ranges between 4 and 6 percent, with a fusion temperature of about 2,0000 F."

Jun 1, 1946

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By Louis C. Srichta

The rapid depletion of known high-grade ore deposits of the Tri-State district and the recognized need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores led to Bureau of Mines examination of several abandoned mining areas for possible deposits adapted to strip mining. Examination of the North Empire tract in Cherokee County, suggested that mineralized zones contiguous to previously mined 2e deposits presented probabilities of meeting the requirements for an open-pit mine - hence the tract was selected for further investigation by churn drilling. The zinc-lead deposit on the property is in a sink-hole structure that has been subjected to intense deformation and silicification. Numerous shafts, mine dumps, and surface caves are evidences of exploitation of an extensive area. The reported active mining period was 1895 to 1905. No production records are available, but it is generally stated locally that the value of the mill products exceeded $2,000,000 which represents considerable production, considering the low metal prices of that epoch.

Jan 1, 1950

By G. S. Rice

The Experimental Mine of the United States Bureau of Mines is a unique coal mine that serves as a large-scale testing laboratory. It is used primarily for testing the explosibility of coal-dust and gases but is also the workshop for many other kinds of research work of which the chief object is to increase safety in mining. The mine is situated in Allegheny County, Pa., about 13 miles southwest of Pittsburgh among the high hills of the west bank of the Monongahela River, at the northeastern edge of the gas-coal district of the Pittsburgh coal bed which extends south through the Connellsville coking-coal district into West Virginia. The Pittsburgh bed, of the Upper Carboniferous age, is one of the most extensive continuous coal beds in the United States, if not in the world. Throughout large areas it shows remarkable uniformity of thickness, levelness, and character of coal, which is a coking coal of high-grade bituminous rank. Its thickness in the northern part is 5 to 5 ½ feet and in the central and southern part is 7 to 9 feet.

Jan 1, 1933

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By P. L. Michael

Several evaluations were made by Modified Rhyme Test (MRT) word lists transmitted through various simulations of the Trapped-Miner Communication System being developed by the U.S. Bureau of Mines. The tests were performed in a "single blind? situation so that the evaluators would not be biased by knowing the characteristics of the system being simulated. A computer program was developed to provide a simulation of the electrical aspects of the communication system and to provide an evaluation by calculation of the articulation index (AI). The study indicates that communication through the presently proposed system will be somewhat unreliable at depths as great as 300 metre even with the system operating at maximum effeciency.

Jan 1, 1977