Search Documents

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

By H. C. Hamontre

The liquid-level gage described in this report is an instrument designed to locate liquid levels in wells rapidly and accurately and, with auxiliary equipment described, to follow moving liquid levels automatically. The depth at which the instrument makes contact with the liquid in a well is indicated at the surface by a depth meter on the cable to which the instrument is attached. When the gage is used to follow a surging moving level, the liquid depth is indicated continuously at the surface. This report contains a description and illustrations of the gage and outlines the operating procedures. The instrument is 1-3/4 inches in diameter and approximately 6 feet in length and may be operated through 2-inch tubing. The gage consists essentially of a float that moves upward with respect to the rest of the assembly, causing a change in the flow of electric current from the surface when the liquid level is reached. The instrument has been tested under a variety of conditions and has been found to be sensitive to changes in liquid level of 1/2 inch. Its accuracy is limited principally by the accuracy of the wire-line depth indicator used. It is not affected by pressure or temperature, and it can be run in open hole or under pressure through a lubricator. It employs only one electric circuit and can be run on an Amergraph single-conductor cable (type 1-H-0) ,

Jan 1, 1954

By S. H. Lorain

"INTRODUCTION The veins of the Clark Fork district have been mined on a small scale since 1913. In May 1943, the district was examined by an engineer 3/ of the Bureau of Mines with a view to possible exploration for larger ore deposits that might be of value to the war effort. The area adjacent to the Hope, Whitedelf, and Lawrence mines was re-examined 4/ December 27, 1943. As a result, the Bureau of Mines started exploratory operations in the district during the summer of 1944 which was continued until the late spring of 1946. This report presents the data obtained from the investigation.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project' as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts the preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1946

By Mayo D. Hersey

This problem was taken up by the Bureau of Mines as a result of the oxygen explosion at the Jefferson Physical Laboratory of Harvard University , and other similar explosions , in order to supply technical information which would serve as a basis for safety precautions in the future . At the Harvard inquiry the fact was emphasized by the Massachusetts State Chemist , Mr. Walter M. Wedger , that we do not know the limiting pressures and temperatures above which compressed oxygen and lubricating oil are capable of spontaneous explosion . The problem is also of importance to the Army and Navy and to the Bureau of Mines in connection with the hazards incurred in the use of compressed and liquified gases in the repurification of helium. In fact , the risk of fires and explosions due to traces of lubricating oil coming into contact with high pressure oxygen is of serious interest to all concerned with the manufacture and use of oxygen , a commodity which is now being produced and distributed on a rapidly increasing scale . Part of the money expended on this investigation was from Army and Navy funds . The problem was undertaken by the Bureau of Mines at the suggestion of Dr. Charles E. Munroe , Chairman of the Committee on Explosives Investigations of the National Research Council , and referred to the Pittsburgh experiment station of the bureau.

Jul 1, 1923

By Stephen A. Swan

Certain types of mobile surface mining equipment are required to be equipped with rollover protective structures (ROPS) capable of protecting the operator in case of a rollover accident. The Bureau of Mines has developed ROPS performance criteria for wheeled front-end loaders. This report reviews the development of rollover test procedures and subsequent testing of ROPS for 52,000-, 286,000-, and 390,000-lb gross vehicle weight (GVW) loaders. The program consisted of both dynamic (roll) and static tests to assist in the development of the ROPS performance criteria. Each test included extensive instrumentation and photographic documentation to fully evaluate the performance of the ROPS. Data summarizing side, longitudinal, and vertical force and deflections are included. The data indicate that for loaders in excess of 240,000 lb, GVW, a side force-to-mass ratio of 1.0 and an energy-to-mass ratio of 6.0 appear to be adequate criteria to protect an operator in the event of a 5400 rollover. For smaller machines, Society of Automotive Engineers (SAE) 11040 performance criteria provide adequate protection. Longitudinal loading, though not ad-dressed in previous ROPS performance criteria, was shown to be a potentially significant factor in ROPS failure. Longitudinal loading and energy criteria equal to 80 pct of side loading criteria are recommended.

Jan 1, 1988

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By M. M. Tilman

The objectives of this research were to determine the practicability of using cobalt as a means of controlling the amount of ferrite in the micro-structures of semiaustenitic stainless steels, and to determine the effects of reduced ferrite content on mechanical properties of these steels. Cobalt additions of up to 3 weight-percent were made to type 17-7 PH2 (AISI 631) stainless steel. Ferrite contents were determined for alloys in the aged condition, and for alloys quenched from the hot working temperature. Ferrite can be completely eliminated from the microstructure of 17-7 PH stainless steel by additions of cobalt, but complete elimination of the ferrite phase results in lower tensile strength, yield strength, and hardness. Tensile properties, hardness, and impact strength were determined for aged material. A subzero temperature treatment before heattreating was necessary to obtain maximum strength in the alloys containing cobalt. Addition of 2 weight-percent cobalt enhances mechanical properties of 17-7 PH stainless steel.

Jan 1, 1968

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By Joseph B. Cummings

"Occurrences of fluorite on the Packard property were first examined by an engineer3/ of the Bureau of Mines in July 1943 as the result of receipt of an application for an access road. In August of the same year the showings were examined by a geologist4/ of the Federal Geological Survey. The property was again examined by an engineer5/ of the Bureau of Mines in March 1944. This last examination resulted in a proposal that access be gained by construction of a truck trail and that the Bureau of Mines undertake to explore the fluorite showings.The truck trail was constructed by the Public Roads Administration, which began the work on February 17, 1945, and completed it 8 days later.The Bureau of Mines exploratory program was completed on May 16, 1945. It consisted of stripping overburden, trenching, test pitting, tunneling, sampling, and topographic mapping.In addition to being described in some detail, the extent of the work as well as results are shown in accompanying tables and figures.Mrs. Rhoda A. Packard, Mrs. Nora 1. Cline, and C. B. Pettingill, all of Tonto Basin, Ariz., own the property, which comprises four contiguous, unpatented lode mining claims recorded at Globe, Ariz., as the Walnut and the Bluebird 2, 3, and 4. The claims are situated in T. 6 N., R. 11 E., Gila County. David L. Roscoe of Tombstone, Ariz., holds a lease and option to purchase.Access to the property is by Highway 88 from Globe, 34 miles to Roosevelt, thence 24 miles by a graded county road along the west side of Roosevelt Lake to Tonto Basin. Here the Greenback Ranch road, constructed by the Forest Service and maintained by the county, crosses Tonto Creek and continues easterly to the foothills. The truck trail leaves the road 8.5 miles east of Tonto Basin and runs 2.5 miles in a southerly direction to the property. (Fig. 1.)The fluorite deposits lie in and along a small canyon in a rough, rocky area at an altitude of about 3,400 feet, Vegetation is scant and of the usual desert variety. The summer climate is dry and hot and the winter climate moderate. Rainfall at the Forest Service Station in Tonto Basin was 11.4 inches from May 1944 through March 1945."

May 1, 1946

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Ruth F. Brinkley

This report is the 16th of a series of reports originally issued annually and more recently biennially to acquaint the reader with the work of the Explosives and Physical Sciences Division, Region VIII.3/ In the majority of instances the results of the investigations are made available to the public through Government publications and journal articles. In certain instances (specifically as regards security-classified research, investigations of a confidential nature, and short-range programs of very limited scope) results are reported only to those immediately concerned.

Jan 1, 1957

By C. F. Jackson

This paper describing the mining practices at a mine in the Southeast Missouri district is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The conditions, operating methods, and practice described in the following pages arc those obtaining at a property in the Southeastern Missouri lead belt, St. Francois County, Mo. This property is the eldest in the county and is a consolidation of a number of separate mines originally opened up as individual operations many years ago. Present-day operations have necessarily to be adapted to suit the older levels, stones, and pillars, and also the recovery of ore from worked over areas which was considered too low grade to mine in the earlier days constitutes a different problem than that of development and mining in virgin ground.

Jan 1, 1929

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By R. R. Wells, G. M. Potter, A. O. Ipsen

This paper gives results of laboratory and pilot - plant investigations of concentration of western manganese ores during the Bureau of mines manganese-development program initiated in December 1940. The data summarize results obtained from laboratory investigation of concentration of ores from three properties in southeastern Arizona . The high - grade Gray - claims lot B ore , a product of hand sorting , is marketable directly or after sintering treatment . Intermediate - grade lot A selectively mined ore would be marketable after sintering as a plus 35 percent manganese produce , but gravity concentration methods were employed effectively to produce high - grade manganese concentrates with over 80 percent recoveries . Complex association of fine - grained manganese oxides , calcite , and fluorite in a siliceous ground mass limited the recovery of high-grade manganese concentrates obtainable from the low-grade Pyrolusite -group ore . A recovery of 63.7 percent of the manganese was made by flotation in a concentrate that sintered to plus 48 percent manganese grade . The low-grade Davis ore contains iron and manganese oxides too intimately associated to permit production of marketable manganese products . However , good rejection of calcite gangue was obtained by flotation , and the enriched manganese - iron product might have value as a spiegeleisen ore .

Feb 1, 1946

By Thomas E. Lobb, Harry C. Verakis

This article examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are:(a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f)training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Significantly increase the amount of fresh air that sweeps the face in front of a continuous mining ma-chine, in order to prevent methane gas buildup. Approach Water sprays are mounted along the sides of a continuous miner and behind the cutter head to help push ventilating air along the required path, and prevent its short circuiting. How It Works A continuous miner is fitted with two sets of water sprays, one of which is used at a time. The set of sprays shown in the diagram, helps move the ventilating air forward along the left side of the miner and across the cutter drum from left to right. That air is then drawn into the exhaust air passageway located along

Jan 1, 1978

By FRANCIS FEEHAN

Safety first is no longer merely a motto ; in some industries and in some parts of the mining industry it is an accomplished fact . In connection with the National Safety Competition of 1928 in which 284 mines and quarries participated , 42 plants were operated without a single lost - time accident . The winning company in the bituminous group had an accident severity rate of 0.053 per thousand man hours of exposure . Excellent safety records of various kinds are becoming more and more frequent , and the indication is that in reality safety is first in many mines and qquuaarrrriieess .. The safety achievements in the Stewart mine of W. J. Rainey , Inc. , are unusual even among mines winning awards in the competition .

Apr 1, 1930