Search Documents

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By H. E. Powell

A solvent extraction procedure was developed on a laboratory scale for recovering trisodium phosphate, zinc, and iron from waste phosphate sludge as separate products. The sludge was dissolved in hydrochloric acid, and iron was extracted as ferric chloride by isopropyl ether. Zinc was extracted by di-2-ethylhexyl phosphoric acid in kerosine. The efficiencies of the one-and two-stage extractions ranged from 98 to nearly 100 percent. Trisodium phosphate was recovered by crystallization from the raffinate. The value of two marketable products is considerably more than than the costs of the major reagent. The process was developed to permit recycling of values in this waste and to consequently reduce stream pollution from this source.

Jan 1, 1972

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By Frederick K. Allgaier

This is the first in a series of progress reports on the longwall subsidence research program at the Bureau of Mines Denver Research Center. As part of this program, the Bureau and the Utah Power and Light Co. are cooperating on a study conducted at the Deer Creek Mine, which is directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. A monitoring network has been established at the Deer Creek Mine to measure subsidence over four adjacent longwall panels. To date, two panels have been mined. Subsidence began as the first panel was mined and continued for 1 year following completion of the panel, during which time the adjacent panel was mined" A maximum of 2.7 feet of subsidence occurred over the two longwall panels mined at a depth of 1,500 feet. Because of the length of time that subsidence continued after mining, the final subsidence profiles and angle of draw have not yet been determined.

Jan 1, 1982

By W. W. Agey

Past investigations on waterborne impurities in the flotation process have been concerned primarily with the treatment of specific ores with particular local waters. Although some anions and cations present in water are known to react with flotation reagents, a definitive study has not been made on the effect of such common ions upon the flotation process. This report describes the fundamental research undertaken to define and measure the adverse and/or beneficial effects of different concentrations and combinations of several common anions and cations when oleic acid is used to froth-float limestone from a pulp of quartz and limestone. Research on the effect of waterborne impurities upon the flotation process was composed of two equally important phases. The first phase comprised development of a procedure for floating limestone from quartz that would give the same results in test after test. Some difficulty was encountered, but once such a procedure was developed, the second phase, comprising study and measurement of the effect of various ions c on to natural water upon the flotation of limestone, was quickly completed.

Jan 1, 1963

[ ]

Jan 1, 1981

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By W. Hermanson

This report presents the results of a task to complete a final design of a remote controlled hi-roof bolting machine for high roof areas in coal mines. The project was begun by visiting several coal mines to become familiar with roof fall areas. Several machine concepts were generated and presented to the design committee for criticism. A preliminary design was completed, as covered by this report. A Final Design and Final Report will be issued incorporating the committee comments at the Preliminary Design review and comments received concerning this Preliminary Design Report.

Jan 1, 1979

By H. R. Beard

The citrate process for sulfur dioxide emission control was developed in pursuit of the Bureau of Mines goal of minimizing the adverse environmental impact of mineral-processing operations. This publication describes the gas analysis procedures used during development of the process. The research required the capability to analyze SO2, H2S, CO, CO2, COS, volatile hydrocarbons, NO, NO2, O2, N2, and H2. The methods described include gas chromatography, electrochemical detection, infrared spectroscopy, and the use of a computer program to predict the product composition in complex reactions. Laboratory and pilot plant applications are discussed.

Jan 1, 1979

By E. M. Tignor

A research program to aid development of improved methods for increased production of petroleum from partly depleted reservoirs is a vital part of the Bureau of Mines effort to effect true conservation of that mineral resource. This report presents results of an investigation to identify the clay minerals within some Appalachian petroleum-reservoir sands, the effect of clay content on the fluid-flow behavior of those sands, and the use of brines in water-flooding operations. Permeability measurements using kerosine, calcium chloride brine, simulated oilfield brine, potassium chloride brine, sodium chloride brine, and distilled water were made on reservoir-rock cores. Clay fractions were separated from sand grains of disaggregated portions of each core sample, and the clay minerals were identified by the differential thermal analysis method. Relations of the permeability to various fluids were developed.

Jan 1, 1957

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

By Foster Fraas

The objective of this research was separation of one highly conductive mineral from a second conductive mineral , a procedure which is impractical in commercial electrostatic separators using metal rolls . Such separators permit separation of nonconductive from conductive minerals . A new technique involved use of carrier electrode rolls specially prepared by anodizing and / or oxidizing at high temperatures to form suitable oxide surfaces . Specific oxides included aluminum , copper , and nickel . The significant result provided by the new surfaces was the extension of the separation range to higher conductivities , an extension in relative mineral conductivity from 10-14 mhos . The results are in accordance with the blocking- layer theory .

Jan 1, 1964

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987

By Ε. P. YoUNGMAN

This paper presents one of a series of digests of foreign mining legis- lation and court docisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in vericis foreign countries. This interpretation of the laws - of Italy has been prepared, in part, from an aclysis made by John W. Frey, for merly associate mineral economist, U. S. Bureau of Mines. It incorporates addi- tional data and comments offered by Enrico Giobbe Della Pitta, a well-known Italian lawyer, in response to a questionnaire. These comments were forwarded by Harold H. Tittmann, American chargé d'affaires ad interim, at Rome, and trans- mitted to the Bureau of Mines through the courtesy of the Department of State.

Oct 1, 1930

By Clarence Hall, CHARLES F. MUNROE

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its impor- tance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes. Both the quantity of explosives used and the number of purposes to which they are applied are increasing. They are now made at about 150 plants, in different parts of the United States, and the product of a single year is estimated at nearly 500,000,000 pounds. Nothing in all this material is a safe or "safety" explosive when in the hands of a careless or ignorant person; and this is true whether considered in connection with the shipment or the use of these explosives. In addition to the large losses of life and property resulting from an improper use of explosives in mining, the recent statistics of the railway bureau for the safe transportation of explo- sives have shown more than 400 persons killed or injured and over $3,000,000 worth of property destroyed by explosives in transit by rail. The fact that three years of cooperative effort under the wise supervision of this bureau has reduced these losses to almost nothing encourages the hope that similar cooperative effort may likewise greatly lessen losses of life and property from the use of explosives in mining. The additions to the large death roll of our mines make a recurring appeal to the public for fair treatment of the coal-mining industry, and to the miner and the manager that they join in every possible effort for greater safety. It may never be possible under conditions such as exist to-day to prevent mine accidents entirely. Little can be accomplished in that direction by either the operators or the miners working alone, but experience in all countries shows that

Jan 1, 1911

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube&apos;s deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support&apos;s resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984