Search Documents

By E. F. Ferrell

The Bureau of Mines, U.S. Department of the Interior, studied the use of manganese sea nodules for catalytic oxidation in air of 1 pct carbon monoxide, 1 pct propane, and 1 pct methane. Catalysts were prepared from both Pacific Ocean and Atlantic Ocean nodules and compared with a platinum catalyst using a fixed-bed, steady-state microreactor with gas chromatographic analysis. Combustion temperatures with manganese nodules were 50° to 100° C lower than those with the platinum catalyst. Ion-exchange addition of rare-earth promotors to the nodule catalyst decreased combustion temperatures an additional 5° to 45° C.

Jan 1, 1978

By K. K. Kelley, W. W. Weller

This report contains experimentally determined heat capacity data for four crystalline sulfides -- AsS , GeS , NiS , and Ni3 S₂ -- over the temperature range from 50 ° to 298.15 ° K. The heat capacity data were used to evaluate the entropies of the sulfides at 298.15 ° K. Entropies of formation from the metals and rhombic sulfur and from the metals and diatomic sulfur gas are also included .

Jan 1, 1964

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By M. E. Tyrrell

Despits its high melting point (2,135° C.), resistance to attack by molten metals, and its hardness (8), spinel (MgO?Al203) synthesized by the fusion of alumina (Al 2 0.) and magnesia (MgO) is not used on a large scale as a commercial furnace lining, mainly because of the prohibitive cost. This investigation by the Federal Bureau of Mines was prompted by the possibility of producing synthetic spinel from inexpensive raw materials by methods outlined in U.S. Patent 2,029,773, "Process for Obtaining Products Containing Spinets," dated February 4, 1936. In this patent Ture B. Haglund described a process for recovering crystalline spinels from melts in the system Mg0?Al203-2CaO-SiO2, a system well suited to the use of starting materials such as dolomite CaMg(C03)2, olivine [2(Mg?Fe)0.Si02], and bauxite (Al203?2H20) which are abundant in the southeastern United States. Compositions, ranging from a low content in the eutectic mixture of 35 percent spinal and 65 percent dicalcium silicate (2 CaO?SiO2) to a high of 75 percent spinel and 25 percent dicalcium silicate, were fused in electric furnaces of the arc-resistance and internal-resistance types. So long as members of the system were in proper chemical balance, "dusting" slags could be produced over the entire range of spinel concentration.

Jan 1, 1961

By C. M. Frost

Crude shale oil prepared by gas-combustion retorting of Colorado oil shale was hydrogenated over a cobalt molybdate catalyst at an operating pressure of 1,000 psig, temperatures of 781° and 761° F, and liquid hourly space velocities of 0.10 and 0.05 Vo/Vo/hr, respectively. The yields of total liquid products and the amounts of nitrogen and sulfur removed were comparable with those obtained at an operating pressure of 3,000 psig and a liquid hourly space velocity of 1.0 Vo/Vo/hr. Approximately 1.5 times as much gasoline was produced at the lower pressure and space velocities.

Jan 1, 1973

By J. H. Field

Results of studies by the Federal Bureau of Mines on a pilot-plant scale for removing hydrogen sulfide and carbonyl sulfide from gas mixtures by the hot carbonate system are given in this publication. Gases containing up to 10 pet. hydrogen sulfide and 48 grains carbonyl sulfide per 100 cu.ft. were treated. In most tests carbon dioxide also was present and was removed simultaneously with the sulfur compounds. Because the rate of absorption of hydrogen sulfide is much more rapid than that of carbon dioxide over a wide temperature range, selective removal of hydrogen sulfide occurred in the bottom section of the absorber near the point of gas entry. Hydrogen sulfide was removed to pipeline specifications with carbonate solutions by using split-stream flows in the absorber and regenerator.

Jan 1, 1960

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

By E. D. Gardner, Edmund Stein

"IntroductionMassive sulphides occurring in metal mines are inflammable and furnish the fuel for many mine fires. Actual sampling has shown that dangerous amounts of sulphur dioxide and hydrogen sulphide may occur in mine atmospheres after blasting in massive sulphides. Probably some .of the finer sulphide in the material being blasted burns while it is in contact with the flame from the explosion. It’s also possible that oxygen of the explosive enters into the reaction.That sulphide dusts are explosive under some conditions has long been suspected, but the theory has not been generally accepted as having been proved. Evidence now at hand appears to be conclusive that such explosions do occasionally occur in mine workings in massive sulphides. Information from several mines working in heavy sulphides shows that occasionally, sulphur dioxide in larger amounts than could be expected from the blasting alone are occasionally thrown out into the mine atmosphere during blasting. Accidents have occurred and lives have been lost by men being caught in such gases. Also it appears in a few cases that damage done to timber in stopes by concussions has been greater than could 112.ve been expected from the regular blasts. In most of these cases the unusually large amounts of Sulphur dioxide could only be accounted for by an explosion or by an ignition of sulphide dusts. When this occurs it is probable that the settled dust is stirred up by the first shot of a round, then the dust cloud is ignited by this or a succeeding shot.In one instance, the senior author, while wearing breathing apparatus, returned to a station to take a gas sample immediately after a raise round had been blasted, and encountered a heavy white fume or smoke that was corrosive to the skin and which forced a retreat. The sample, which was taken farther back in a greatly diluted atmosphere, showed a high percentage (0.18) of sulphur dioxide. The station and the raise which was just being started were very dry and the walls and floor of the station contained settled sulphide dust which apparently was ignited by the blast."

Mar 1, 1928

Use water-jet-assisted cut-ting technology to reduce the exposure of mi ne workers' to respirable dust. Approach Install water-jet-assist on mining machines and evaluate its impact on respirable dust. How It Works Water-jet-assisted cutting involves a mechanical cutting bit working in combination with a moderate pressure (generally up to 10,000 psi) water jet directed just in front of, or through, the bit tip. One of its advantages is reduced dust generation because the jet wets the face of the material being cut more efficiently than a conventional low-pressure water spray, thus capturing much of the dust before it ever becomes airborne. It also removes loose cuttings ahead of the bit before they are pulverized by the bit into respirable dust. Total water consumption is about the same as for conventional low pressure dust control water spray systems. However, there is some increase in power consumption because of the energy needed to provide the high pressure water.

Jan 1, 1987

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

By Stephen Gerard Sawyer

The Bureau of Mines developed a method for analyzing elastically certain types of protective cabs and canopies used on underground electric face equipment. The method is based on plane frame theory, and to be amenable to analysis by this method, cabs and canopies must contain symmetry about one plane. Additionally, protective structures with one or more top members in the long direction that do not frame into the columns should be approximately twice as long as they are wide and have two or more internal top members in the short direction. The assumptions and limitations of the plane frame method as regards analysis of three-dimensional cabs and canopies are discussed. A step-by-step procedure for application of the plane frame method is given, and three example canopies are analyzed following this procedure. Elastic strengths calculated for the three example canopies compare within 10 percent of those computed by the more complicated space frame analysis. Formulas employed in plane frame analysis of cabs and canopies are given in the appendixes.

Jan 1, 1973

By E. G. King

Difficulty has been encountered in making thermodynamic calculations of metallurgical reactions involving interoxidic compounds of the ferroalloy elements because of the serious lack of most thermodynamic data for these substances. This Bureau of Mines report (the first of a planned series dealing with entropies of vanadates, tungstates, and molybdates) presents low-temperature heat-capacity data and entropy values at 298.15° K. for three crystalline sodium vanadates--metavanadate (NaV03), orthovanadate (Na3VO4), and pyro-vanadate (Na4V2O7). The results are combined with data for the constituent oxides and elements to obtain entropies of formation of the vanadates. Previous to this report only one vanadate had been studied Similarly, ammonium metavanadate.4/

Jan 1, 1961

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By W. H. Oppelt

A lignite from west-central North Dakota (Mercer County) was dried by the Bureau of Mines by the Fleissner process at saturated steam pressures to 1,500 pounds per square inch absolute (p.s.i.a.). Normally, the process is operated at pressures of 200 to 370 p.s.i.a. At the highest pressure the temperature of the saturated stearn is 596° F. The purpose of the investigation was to evaluate the influence of very high stearn pressure and temperature on moisture removal, steam consumption, and physical and chemical characteristics of the dried lignite. Two drying cycles were used: A normal cycle, corresponding to previously established standard time requirements, and an accelerated cycle, wherein time requirements were determined by boiler capacity and handling speed. Blank tests to determine stearn requirements for heating the empty autoclave were performed for each cycle and each test condition. Moisture removal, final moisture content, net steam consumption, and size stability of the dried lignite were determined.

Jan 1, 1959

By Manuel Gomez

Carbon number distributions were obtained for tar acid fractions from five low-temperature tars by low-ionizing voltage mass spectrometry. Quantitative data for phenols representing seven structural compound types were examined by statistical analysis. It was shown that for the phenols discussed, the data could be represented by regression equations expressing phenolic concentration as a function of the reciprocal of the carbon number and the carbon-to-hydrogen ratio of the parent coal. The total concentration of each structural type present was found to depend on the molecular weight and boiling point of the initial member of the group. Carbon distribution data for the tar acid fractions studied support the view that low-temperature tars contain the same chemical compounds but in different proportions.

Jan 1, 1965

By Daniel W. H. Su, Gregory J. Hasenfus

This paper demonstrates that finite-element modeling can be used to predict in situ coal pillar strength, especially under non ideal conditions where interface friction and roof and floor deformation are the primary controlling factors. Despite their differences in approach, empirical, analytical, and numerical pillar design methods have apparently converged on fundamentally similar concepts of coal pillar mechanics. The finite-element model results, however, are not intended to suggest a new pillar design criterion. Rather, they illustrate the site-specific and complex nature of coal pillar design and the value of using modeling procedures to account for such complex site-specific conditions. Because of the site-specific nature of coal pillar design, no single pillar design formula or model can apply in all instances. Understanding and accounting for the site-specific parameters are very important for successful coal pillar design. More work remains before the century-old problems related to pillar design are finally solved. Future research should focus on the cross-linkage of empirical, analytical, and numerical pillar design methods.

Jan 5, 1999

By Richard F. Link, George W. Gladfelter, George S. Koch

Contour maps, useful in mineral industries, for example, in analysis of trends in mineralization, may be constructed through statistical methods of regression analysis programed for an electronic computer, For many applica­tions, the resulting maps are more useful and objective than conventional contour maps that are necessarily subjective because they are drawn by hand methods. In principle, an equation is found that fits a quadratic surface to observed elevations of points referred to a datum plane, The quadratic sur­face, represented by a contour map may take the form of a ridge, valley, dome, or basin, Once an equation has been derived, its coefficients may be used to construct a contour map--showing lines of equal value that are derived from the original observed data points by the averaging process of fitting the quadratic surface. Methods employed are illustrated by an example analysis, based on data from a large vein of the Fresnillo mine, Zacatecas, Mexico. Computer programs to implement the methods are described in an appendix,

Jan 1, 1964

By Jerry L. Huiatt

An accurate and reproducible procedure was developed using the gas-liquid chromatograph to quantitatively measure oleic acid on flotation products and in flotation water phases. The method comprised extraction of the oleic acid from the mineral surfaces with alcoholic NaOH, esterification of the extracted oleate, and chromatography of the methyl ester with an internal standard. Quantitative analysis of oleic acid on flotation products from test tube and bench-scale flotation tests with pure minerals and with natural ores proved the applicability of the method on a variety of minerals. The accountability of oleic acid added was 100 percent, ±5 percent.

Jan 1, 1968

By G. S. Rice

The recommendations of the Bureau of Mines on rock-dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions,5 approved by the. American Engineering Standards Committee,6 December 30, 1925 It is specified that the dust to be used is of a size that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch.

Jan 1, 1930