Search Documents

By G. Molinda, D. Dolinar

Each year, about 2,000 falls of supported roof occur in the more than 800 underground U.S. coal mines. Therefore to help improve the design of primary support systems, the National Institute for Occupational Safety and Health (NIOSH) conducted a nationwide study of roof falls in over 2,500 km of roadways at 37 coal mines. Information on the roof falls as well as other geotechnical, mining, geologic and roof bolting factors were collected and quantified Then a multi variate statistical analysis was conducted on the data with the roof fall rate being the outcome variable The results were used to derive preliminary design guidelines for predicting the roof bolt length, capacity, and pattern required to effectively reduce the roof fall rate. The equations are fairly limited by a relatively high statistical variance in the data. Also reported is a recent survey of U.S roof bolt manufacturers that shows a significant change in bolt types used over the last ten years.

By Chelesa C. Woodward, Gregory G. Miller, Walter K. Utt, Wayne L. Howie

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the use of a drill monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof so that roof drill operators can be warned when a weak layer is being drilled. Measurements taken during drilling can be converted to suitably scaled features so that a neural network can classify mine roof strata in terms of relative strength. The feasibility of this concept has been demonstrated in the laboratory. The research project was undertaken in order to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills used in underground mining and would likely find wider application as well.

Jan 1, 2002

By R. V. Ramani, A. S. C. Owili-eger

The Methane Generator program is a part of the Internal Environ¬mental Sub-system of the Master Design Simulator (MDS). All the sub¬systems of the MDS are controlled and activated by the main program as required. The data requirements for the Methane Generator are supplied by the Geology and Reserves sub-system through common storage. Figure 6 shows the information flow between the Methane Generator and other systems of the MDS. It should be noted that the Methane Generator can also function independently as was described under model application. AREAS OF MISSING INFORMATION In any numerical analysis, the accuracy of the solution depends entirely upon the data available. In gas flow problems, parameters that constitute basic model input data are rock porosity, medium permeability, reservoir pressure and initial reservoir pressure dis¬tribution. Unfortunately, however, most of these characteristics are not available for a lot of coal seams. The need for actual field data cannot, therefore, be adequately emphasized here.

Jan 1, 1974

By E. P. Youngman

The Ottoman law, which was in force in Palestine before the British con- quest of the country (1917-18), still forms the basis of the legal system. Nevertheless, with respect to mining, legislation has been considerably re- vised since the British occupation and mandate, some of the Ottoman laws having been either radically altered or wholly abolished, in order that the legal status of Palestine might be more in harmony with that of western States. Legal transition is still far from being complete; however, no further mining legislation is pending at the present time (March, 1931). Revisions during the British military occupation (1917-20) took the form of proclamations of the commander in chief. After the establishment of the civil administration (1920) changes in the legal system were a decided de- parture from the Turkish laws. In 1922 the practice was begun of giving con- secutive numbers and short titles to the ordinances. The basic mining law is the mining ordinance of 1925, No. 19 (amended by mining ordinance No. 10 of 1926), an "ordinance to make provision regarding the winning of minerals, and the conditions under which minerals may be gotten, and to replace the existing Ottoman laws relating thereto." The chief regu- latory provisions are embodied in regulations (A) and (B)--mining ordinance, 1925. This mining legislation of 1925 repealed the following laws:

Nov 1, 1931

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

1. Mining to prevent and control underground acid formation should begin with education imparted through: (A) Course work at mining schools to teach prospective engineers. (B) Training of engineers presently employed in the mining industry through appropriate mining extension courses. 2. Considerable need exists to devote more attention to: (A) Hydrogeologic studies of mining areas to enhance the planning of new mines and the abatement program of existing mines. (B) Additional research to explore methods of dewatering the strata associated with mining areas. (C) Further effort to develop sealants for preventing contact between water or oxygen and the acid producing material associated with the coal seam.

Jan 1, 1970

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The usual run time errors occur when illegal mathematical operations are attempted by MFIRE For exam¬ple, if the user enters a negative value for the input variable HEAT to model a heat sink or cooling station, a run tame error will occur because an exponential function is employed to better model the changing temperature dis¬tribution in the airways. DATA FILE ERRORS Two types of data file errors can occur. 1 An error may occur because the input data file itself is invalid This may be caused by: The data file cannot be found due to incorrect spelling, drive, or path specification Check the spelling and path at the prompt for location of the data file. The data file contains non-ASCII symbols Check op¬eration of the text processor to insure that only ASCII characters are produced Delete all non-ASCII and/or all out of place characters. 2 Data are accepted by the program, but are incorrect for the data types or ranges or the combination causes a data inconsistency This may be due to. An invalid character is located where a numerical value is required The input data value is outside the reasonable range The input data is insufficient to build the model for simulation. The input data exceeds the capacity of the program. PROGRAM ERROR DETECTION When the program is running, tracing messages are given on the screen indicating the group and lines of data that have been read and the section of the program that is executing Program termination indicates that problems are caused by the subsequent (not read) data file section. For each detected error, descriptive message starting with * ERROR * is issued and the program terminates. When a possibly wrong value and/or its calculated intermediate result is detected, a descriptive message starting with * WARNING * is issued and the program continues. If a modification of input value or calculated intermediate result is automatically made by the program, descrip¬tive message starting with * ATTENTION * is issued and the program continues. LOCATING ERRORS If a message indicates that the error condition occurred due to the data input file, locate and correct the data item. If no error message is issued, but the simulation results are not as expected, carefully check the list of input data shown in the output file WARNING messages and ATTENTION messages may reveal an error in the input data even though the program continues to operate Insure that the default values or modifications adopted by the program run are acceptable. Anomalistic data, though not incorrect or impossible, may lead to an unusual simulation For example, making a fan unusually powerful may prevent a normal strength fire from affecting the airflow distribution in the system Much care must be employed before considering an ex¬treme case. If a message indicates that the accuracy criterion in the temperature section of the program was not satisfied, a table detailing the current parameters of airways which have large fluctuation in the average air temperature from iteration to iteration is produced If the pattern of the parameters is clearly cyclical, while the variation of natural ventilation pressure is stable or cyclical from iteration to iteration, then, most likely there is no single equilibrium stage for the event If the variation of natural ventilation pressure decreases steadily though slowly, increasing the value of data item variables MADJ or ITN (on control line number 1) may allow convergence.

Jan 1, 1990

By E. P. Youngman

The mining laws of Russia (Collection of Laws, vol. 7, 1912) are still in force in Latvia. The Free State of Latvia (declared independent on November 8, 1918) is composed chiefly of the Baltic Provinces of the former Russian Empire, which are ethnographically Lettish: The Province of Courland, four districts of the Province of Livonia, and three districts of the Province of Vitebsk. Since the establishment of its independence, Latvia has not felt the need of a special mining law, inasmuch as mining so far has not been found profitable in that country. A supplement to this paper, entitled "Mineral Resources," is a brief summary of the minerals found and utilized in latvia. RIGHTS OF FOREIGNERS A foreign individual is permitted to explore for minerals and to own and operate mines in Latvia on equal terms with Latvians. A foreign corporation is required to establish a branch in Latvia, which shall be subject to the corporation laws of the country. A certain number of the partners or incorporators must be citizens of Latvia.

Nov 1, 1931

By T. E. Marshall, D. R. Dolinar, T. M. Barczak, T. P. Mucho

Over a portion of the older limestone mine workings at the NIOSH Lake Lynn Laboratory, a mining health and safety research facility, a large sinkhole formed caused in part by the intersection of several tightly spaced joint sets and unusual weather conditions. The anticipated propagation of the associated roof failures threatened to encroach upon a portion of the facility’s secondary escapeway. To protect the escapeway, two cribs walls and over 80 cable bolts were installed. In addition, extensometers were installed to monitor roof movement in the escapeway. However, a large roof fall associated with the propagating roof failures in the sinkhole area partially destroyed one crib wall where the adjacent escapeway was not reinforced by cable bolts. Recent roof movement information indicates that this area is still active. Based on these measurements, steps have been taken to stabilize this portion of the escapeway. This paper discusses roof monitoring, the roof movement, the large roof fall, propagation of the roof failures, and the recent support measures undertaken to stabilize the escapeway.

By V. P. Bhavanandan

The mucus secreted in the respiratory tract provides the first barrier against inhaled particulate and gaseous toxicants. Trachea removed from pathogen-free rats were maintained as organ cultures and used to study the effects of coal dust exposure on the synthesis of mucin. The high molecular weight isotopically labeled (3H-glucosamine, 14Cleucine or 35S-sulfate) mucin could be purified by gel filtration, treatment with testicular hyaluronidase, ion exchange chromatography, delipidation and CsBr density gradient centrifugation. To examine effect of coal dust on mucin production, groups of explant cultures were exposed to media containing coal dust at 100 µg per ml every 2 days for 2 weeks while control cultures were treated with media without dust. Analysis of the spent culture media showed that treatment with dust markedly decreased the production of nondialysable glycoproteins as well as hyaluronidase-resistant acid-precipitable fraction consisting mainly of mucin. Since the synthesis of protein was not affected to the same extent the decrease in mucin production is not entirely due to cell death. In separate experiments rats were subjected to in vivo coal dust exposure in inhalation chambers and tracheae of these and control rats were removed for explant cultures. The incorporation of precursor isotopes into mucin by these explant cultures are being examined. (Supported by U.S. Bureau of Mines through the Generic Mineral Technology Center for Respirable Dust under grant G1135142, project 4210).

Jan 1, 1988

In the last few decades, a considerable amount of effort was directed at accurately determining the coal pillar strength to use for safely designing coal mines. The outcome of this early work was the well known Obert-Duvall, Holland-Gaddy, Bieniawski, and Salamon-Munro equations for coal pillar strength. All of these equations were developed for, and were calibrated with, pillars in a large room-and-pillar area such that the loading could be determined using the "tributary-area" theory. In order to account for the abutment loads associated with full-extraction mining, the empirical methods have typically adopted a simple conceptualization of the abutment load through use of an "abutment angle." Short of a complete numerical or analytical analysis of the coal seam and surrounding strata, very little work has been Fretted toward refining the empirical analysis of pillar loading. It appears that the vast majority of the research has been directed at determining the pillar strength, the numerator of the safety factor equation, when the denominator of the safety factor equation, the pillar loading, plays an equally important role in pillar design. This paper will address the deficit of pillar loading research by exploring the accuracy of the empirical abutment load calculations using insight provided by an elastic overburden model, a laminated overburden model and field observations. Ultimately, it is determined that a constant abutment angle probably over-predicts the abutment load as the mining depth increases.

By S. F. Ravitz, T. M. Romslo

During 1940 and 1941, the Bureau of Mines examined a large number of silver mines in Arizona for their potential as producers of manganese ores. Although very little manganese ore had been produced from these mines, it was generally known that manganese oxides in appreciable amounts were associated with the silver ore. Following the examinations, the Bureau further investigated some of the ore deposits by diamond drilling and other types of sampling. The results of these investigations, from the viewpoint of manganese, were discouraging. However, the investigations did indicate that appreciable tonnages of manganese-silver ores had been left in some of the mines by earlier operators. Most of these ores were too low-grade for direct shipping as ores of manganese or silver, and their beneficiation by ordinary processes was not economic. Exploitation of the ores appeared to be dependent upon the development of a low-cost milling method, which would yield a marketable manganese product and recover a high percentage of the silver. Later, the Bureau of Mines constructed an experimental mill at Salt Lake City, Utah, for the treatment of manganiferous ores by the dithionate process, designed to recover manganese as a high-grade product. The dithionate residues can be treated by other processes for the recovery of additional values that may be present in the ore. This development focused attention on the manganese-silver ores of Arizona and led to setting up Bureau project No. 370, which is the subject of this report.

Jun 1, 1947

By I. AITKENS

The group of gems included under the general name "feldspar" occupies only a minor place in jewelry. Feldspars, with the possible exception of quartz, are the most important of rock-forming minerals, but most occurrences are of quite ordinary varieties, without striking color and unattractive. Few specimens are suitable for use as gem stones, but occasional crystals that exhibit unusual brilliance or play of color are cut into various shapes for personal adornment or for architectural decoration. The best known of the feldspar gems, and probably the most important in point of production, is the moonstone. Amazon stones, labradorite, sunstone, and a number of less common varieties have been produced in various parts of the world.

Nov 1, 1931

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By H. M. Lawrence

"In the land-pebble district of Florida a lively interest in the possibilities of obtaining increased recoveries of phosphate rock is evident. Research in several directions is being carried on by companies operating in the district to increase the yields obtained by the washing plants. The Bureau of Mines is cooperating with this research program to promote more efficient plant practice and to avoid unnecessary depletion of mineral resources.Washing practice, as carried on in the district at present for the recover of phosphate rock from the crude ores or matrix, is not a complicated process. Flow sheets of the several companies are similar, although the equipment varies with the preferences of the individual operators. For disintegrating the matrix log washers are favored, although revolving drums equipped with flights to break up lumps of clay are also used. Fine sand is removed by screening. Vibrating screens have become well established in the district, although stationary flat screens and trammels are also employed.The writer acknowledges with appreciation the cooperation of the phosphate companies in the land-pebble district; suggestions and criticism by Will. H. Coghill, supervising engineer, Ore Dressing Section of the Bureau of Mines; and the laboratory assistance of J. O. Davie, J. W. Pamplin, and E. Roca, cooperative fellows of the University of Alabama.Losses in the Finer SizesOf the phosphate that is not recovered by present washing methods the greater portion is in the finer sizes. In these sizes the phosphate grains are accompanied by grains of sand - largely quartz - of the same size, and recovery of these phosphate grains as a commercial product is not possible by simple washing methods. Phosphate recoveries approaching complete extraction can only be effecte by applying metallurgical processes, either mechanical or chemical. As yet, most of these processes have not advanced much beyond the laboratory or perhaps the pilot-plant stage. Such processes may have some application to the beneficiation of phosphatic ores or washer rejects, but a discussion of them is not within the scope of this paper."

Apr 1, 1929

By James Rowland

On June 1, 2004, the underground coal mine ventilation safety standards under the Code of Federal Regulations (Title 30, Part 75) became effective for the use of a conveyor belt entry as an intake air course to ventilate working sections. These standards, also known as the Belt Air Rule, contained a section which limited the air velocity in the conveyor belt entry to no greater than 500 feet per minute unless otherwise approved by the US Mine Safety and Health Administration in the fire suppression system section of a mine?s ventilation plan. The Belt Air Rule included a requirement dictating compatibility of air velocity with fire suppression systems. The final rule of limiting air velocity in the belt entry was challenged in the Court of Appeals for the District of Columbia Circuit. The court granted that petition and vacated the requirement on the air velocity cap, according to MSHA. The removal of the air velocity cap from the final rule, paired with the compatibility requirement, led to a need for research on high air velocity?s influence on fire suppression system performance in belt entries. Test data was needed that illustrated the relationship between fire suppression system performance and air velocity, especially with the increased use of wider belts in underground coal mines, so National Institute for Occupational Safety and Health and MSHA collaborated to obtain the data. However, this work was initiated before the revised Belt Air Rule was promulgated on December 31, 2008, when 1000 fpm air velocity became a requirement. Four different

Jan 1, 2009

By Ron Merkel, A. Mayton

Operators of underground mobile equipment, particularly shuttle cars, are often exposed to significant levels of whole-body vibration (WBV) and shock. The human factors group at the NIOSH-Pittsburg Research Center has investigated the use of viscoelastic foam to reduce shock for the equipment operator and improve seats on mine shuttle cars.

By Donald P. Tuchman

The U.S. Bureau of Mimes is investigating Fourier transform infrared (FTIR) spectroscopy for on- filter quartz analysis of respirable dust. A custom accessory is described for full-face examination of filters utilizing a large-diameter infrared (IR) beam. The accessory positions samples to match diameters with that of the diverging analytical beam. Sample absorbance is then measured. With nonuniform deposition of dust on collection filters being a major issue for such analyses, this approach is the most direct way to accomplish sample area averaging. The approach is unconventional since it utilizes large-beam geometries instead of the usually desired minimized beam dimensions. The issues and problems involved in the analysis of quartz on a filter matrix are discussed. Absorption bands chosen, light-scattering effects, curved baselines, random noise, interference fringes, and possible solutions to technical difficulties are the topics covered. The more significant findings include a 20-pg detection limit for quartz when the custom accessory is used and minimal occurrence of light-scattering effects at low wavenumbers. The custom accessory performance was satisfactory and merits further work. With continued research, an on-filter method for quartz analysis of respirable dusts seems achievable.

Jan 1, 1992