Search Documents

By V. L. Nkuna, S. R. Amos, T. Naidoo

"Ivanhoe Mines’ Kamoa copper project is a recently discovered high-grade copper sulphide deposit in the Katanga Province of the Democratic Republic of Congo. The mineralization identified to date within the resource is typical of sedimentary-hosted stratiform copper deposits and comprises three distinct units: supergene, mixed, and hypogene mineralization. Since 2010, various metallurgical test work campaigns have been conducted on drill core from different areas within the deposit in line with resource expansion. The most recent bench-scale flotation test work has shown positive repeatable results. The work was conducted on a composite sample of drill core from the southern part of the Kamoa resource. The sample is representative of the first four to five years of planned production, when Ivanhoe Mines intends to produce clean, highgrade copper flotation concentrate. A detailed test work roadmap developed from first principles for the campaign led to an optimum flow sheet for treating the Kamoa mineralization. Copper recoveries of 88.3%, at a concentrate grade of 39.0% copper, were achieved using a composite sample — an improvement on the previously published 85.9% life-of-mine average copper recovery indicated in the November 2013 Kamoa Preliminary Economic Assessment. IntroductionThe Kamoa project is a newly discovered, very large, stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi in the Democratic Republic of the Congo (DRC) and about 270 kilometres west of the provincial capital of Lubumbashi. Ivanhoe Mines holds its 95% interest in the Kamoa copper project through a subsidiary company, Kamoa Copper SA Limited SPRL, and DRC government owns 5%. The project location is indicated in Figure 1.In January 2013, a new independent mineral resource estimate ranked Kamoa as Africa's largest high-grade copper discovery and the world's largest undeveloped highgrade copper discovery. At this time, Ivanhoe Mines had estimated discovered Indicated Mineral Resources of 739 Mt grading 2.67% copper, containing 43.5 billion pounds of copper, and Inferred Mineral Resources of 227 Mt grading 1.96% copper, containing 9.8 billion pounds of copper, as demonstrated in the Preliminary Economic Assessment (PEA) (AMC, 2013). A 1% copper cut-off grade and a minimum vertical mining thickness of 3 m were applied in each classification."

Jan 1, 2016

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By N. Steven

Published parameters from the Mufulira copper in situ leach (ISL) in Zambia are used for order-of-magnitude flow-rate calculations for an envisaged gold ISL in back-filled Witwatersrand stopes. A successful leach operation requires that the porous medium, usually a sand, has a hydraulic conductivity in excess of 5 x10-7m/second (i.e. a permeability >50 millidarcies).Empirical evidence suggests that average linear velocities would be of the order of 60 m/day if the backfill has the grain size of a fine sand. The proposed gold lixiviant would probably be an alkaline or ammonium thiosulphate, not cyanide. The resultant sulphate-rich ground and drainage waters could probably be processed using existing purification techniques to produce gypsum and magnesium/calcium carbonate. Within the next 100 years it is inevitable that solution mining will find widespread application on the Witwatersrand, if not for gold extraction, then certainly for water remediation purposes.

Jan 1, 2009

Numbering of the Journal Because computer and library authorities prefer journal subscriptions to be based on the calendar year, and because the present numbering system of the Journal of the South African Institute of Mining and Metallurgy does not conform with the calendar year, it has been decided to change the numbering system of the Journal.

Jan 1, 1979

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975

By K. M. Primrose

Electrical tomography has developed rapidly over the last few years in its sophistication and practical use to enable three-dimensional information on the distribution of phases within flowing mixtures to be observed1. This paper reviews the current state of application from the industrial perspective, drawing on applications case studies based on scaling studies in the laboratory right through to installations on plant. In the laboratory, applications have looked at scale-up of mixing2 processes involving gas-liquid and solid-liquid suspensions3 with a particular interest in verifying computational fluid dynamics simulations or in checking scale-up design4,5. In the processing plant, the circumstances are usually bespoke and may range from simple detection of the degree of homogeneity of a flowing mixture through to the need to measurement a sophisticated batch process such as crystallization, sedimentation, filtering and drying. Examples drawn from the chemical and pharmaceutical industries will be presented and related to the benefits that can be gained through application of the method.

Jan 1, 2008

By W. D. Grimsley, R. P. King, J. B. See

Samples (15 to 20 g) of pre-calcined Mamatwan manganese ore or pure Mn 304 smaller than 48 mesh were reacted at temperatures in the range 1000 to 1300°C with samples of spectrographically pure graphite smaller than 325 mesh. Samples (1 g) of ore or pure Mn02 smaller than 48 mesh were reacted at temperatures of 1000 and 1200°C with pure graphite fines in argon, with graphite in carbon, .'1onoxide, and with carbon monoxide alone. In each case, the loss of mass as a function of time was recorded with a hermobalance. The rate and degree of reduction were found to increase with additions of carbon and with increasing temperature up to 1300oC, when they reached their maximum. The shape of the reduction curves, together with the results obtained from examination of the products of reaction by microscopy and X-ray diffraction, were used as the basis for a postulated reduction mechanism. Some details are given of an initial kinetic model that was used to verify the proposed mechanism. It was found that the reduction of Mamatwan ore by graphite at temperatures in the range 1000 to 1300°C occurs in two stages: (i) an initial stage during which the higher oxides of manganese are rapidly reduced to MnO with concurrent formation of CaMn2O4 and (ii) a longer stage during which CaMn2O4 and MnO are reduced to carbides by carbon dissolved in the ferromanganese phase.

Jan 1, 1978

A powerful, interactive metallurgical process simulator for use on micro- computers has been developed in the Department of Metallurgy and Materials Engineering at the University of the Witwatersrand. MICROSIM presently allows simulation of all ore-dressing flowsheets and a selection of hydrometallurgical unit operations, and is extendable to all such processes. MICROSIM is written in Pascal. This modern language provides very versatile data structures which can be effectively used to solve the major problem in generalised simulation programs, namely storage and transmission of data relating to liquid and solid phases. Dynamic memory allocation allows optimal utilisation of computer storage space. The simulator utilises very efficient precalculation algorithms that determine the tear streams for optimal sequential modulator calculation convergence. Microcomputer graphics simplifies flowsheet specification, and form-filling data capture with supplied default values eliminate most common input errors.

Jan 1, 1987

By A. Buncombe

In March 1984, two years' work by senior metallurgical personnel from the six major mining groups culminated in the formation of the Mine Metallurgical Managers' Association of South Africa. This Association has joined a group of specialist Associations operating within the South African mining industry whose aims are to uphold the standards and promote the interests of their various professions.

Jan 1, 1987

By P. A. Botha

The production of iron and steel generates various types of waste materials containing oxides, carbon, and flux material. Usually, these materials are land-filled at the plant site or are hauled away for disposal. Some of these waste materials are hazardous, and they must therefore be recycled or disposed of properly. The influence of different waste materials in iron-ore sinter blends on the quality and operational parameters in sinter production is described. The recycling of waste materials such as dolochar, scrap fines, mill scale, electric-arc furnace slag, basic-oxygen-furnace mud via the sintering process can achieve a saving in the cost of the raw materials (for example, fuels and flux) and a reduction in pollution. A comparison of a typical sinter with a sinter produced through the utilization of waste materials shows a distinct correlation between certain types of waste material and some metallurgical properties and operational parameters. Dolochar (and arc-furnace slag) in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. In general, dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter, but not necessarily the operational parameters such as the production rate. At Vanderbijlpark, approximately 15 kt of various waste materials per month are successfully recycled in the sinter plant. Investigations into the handling and recycling of other waste materials may indicate that even more waste materials can be utilized.

Jan 1, 1993

By NIM REPORTS

Notices CONFRRENCE ON COMPUTRRS IN ENGINEERING The above Conference, which is being organized by the Electrical and Electronics Board of the Institution of Engineer!!, Australia, ill to be held in Sydney on 16th and 17th May, 1974. It is being planned in conjunction with the Sixth Australian Computer Conference and will be held during the week immediately preceding the latter. NIM REPORTS Report No. 1495 A method for the determination of ekmental sulphur on the surface of sulphide minerals. Report No. 1500 The chromatographic separation and determination of nobk metals in matte-leach residues. Report No. 1505 The production of the refractory aluminium saicates, with special refererence to South Africa. Report No. 1517 Computer-controlled flotation plants in Canada and Finland. Report No. 1526 Heat of solution as a control of aqueous-ammonia concentration. Report No. 1529 South African costs of equipment for the metallurgical industry (197).

Jan 9, 1973

By S. M. Spottiswoode

A simple method for the application of excess shear stress (ESS) analysis to the mining of planar reefs is examined. The potential for seismicity associated with mining is expressed as the calculated increase in ESS on a regular grid of points 50 m above the reef, and is compared with observed seismicity around a deep-level, relatively geologicaly-undisturbed gold mine. Thirty regions were studied, involving over 2000 seismic events with magnitudes greater than 1,5 on the Richter scale and associated with almost 2 million square metres of stoping. The total seismicity, measured either as the number of seismic events or as the total radiated energy, corelated more closely with changes in ESS than with ERR. The incidence of rockbursts also favoured the ESS model. Corelation coeficients of around 0,8 for seismicity and ESS indicated that the assumptions inherent in the method used are collectively reasonable. The total seismicity in each region was found not to be strongly controlled by the presence of dykes and faults, although numerous individual seismic events were located close to such features.

Jan 1, 1988

The imbalance between the coal resources contained in thin seams (1,5 m or less) and the production from them is outlined. It is suggested that an Increase In the exploitation of thin coal seams is necessary, and that drum-type continuous miners can produce a substantial amount of any increase. Continuous miners are employed in a number of mining methods including bord-and-pillar, pillar extraction (stooping), rib-pillar extraction, and shortwalling. These techniques of mining are evaluated with respect to production rates and the cost of extraction for South African conditions included in these evaluations are the types of equipment used to transport coal from the mining machine to the section conveyor belt. Computer simulation techniques are used to generate the required production levels, and interpretations are made of other results from the computer modelling. For thin, coal seams, bord-and-pillar mining utilizing continuous haulage is apparently the most productive and cost-effective of all the methods using the continuous miner. The relative efficiencies of the other techniques of mining and of coal-transportation vehicles are also outlined.

Jan 1, 1984

By J. S. Freer

Two very successful schools on 'The design and operation of plants for the recovery of gold by activated carbon', were held from 14th to 18th October, 1985, and from 24th to 27th February, 1986, at Mintek. They were arranged by the Institute in close co-operation with Mr. Peter Bailey of Gencor, who was course leader. Computers and mathematics APCOM 87, the 20th International Symposium of the Application of Computers and Mathematics in the Mineral Industries, is to be held in Johannesburg from 19th to 23rd October, 1987. Interested people are invited to submit titles and synopses in any of the following topics or others. Papers can cover theoretical developments, practical applications, case studies, and software and hardware systems. Tunneling '88 The Institution of Mining and Metallurgy is pleased to announce the holding of 'Tunneling '88', the fifth international symposium and exhibition in the series, from 17th to 22nd April, 1988, at the Kensington Rainbow Exhibition Centre, London, England. Centenary exhibition and conference The major trade show to take place in the year of Johannesburg's centenary will be the 7th International Mining and Electrical Engineering Exhibition- ELECTRA MINING 86. The Exhibition, which is also the third-largest mining exhibition in the world, wil take place from 15th to 19th September, 1986, at the National Exhibition Centre, Crown Mines, Johannesburg. Mining electro technology The Eighth WVU International Mining Electro technology Conference is to be held in Morgantown, West Virginia, U.S.A., from 29th July to 1st August, 1986.

Jan 1, 1986