Search Documents

By Gary L. Simmons

Over the past several years, Newmont Gold Company (previously Santa Fe Pacific Gold Corporation) developed a new technology for the flotation of refractory auriferous sulfide minerals which is referred to as the N2TEC flotation process. Starting in April 1997, the first commercial flotation plant utilizing N2TEC technology was successfully commissioned at the Lone Tree Mine near Valmy, Nevada. The Lone Tree flotation plant was designed to process 4,085 mt/d of ore producing 494 mt/d of sulfide concentrate. A flotation tails leach CIP circuit was added to recover cyanide-soluble gold from the flotation tails. A portion of the flotation concentrate is blended with whole ore feed to the Lone Tree autoclave, up to the limit imposed by the current oxygen plant capacity. The remainder of the concentrate is shipped to either the Twin Creeks autoclaves or the Carlin roaster for subsequent oxidation and gold extraction. This paper discusses the results achieved in the commercial flotation plant compared to pilot plant testing and engineering design flotation modeling. Capital and operating cost information are also presented.

Jan 1, 1999

By S. D. Bearden

The world's barite reserve base is adequate for at least 100 years at the current consumption rate. China, India and the United States are expected to remain the leading producing countries, and the United States will continue to be the largest consumer. None of the known substitutes for barium sulfate are expected to impact existing applications. World production in 1995 was 4.41 Mt (4.86 million st), which is about 50% of capacity. Consumption is directly proportional to hydrocarbon well installation activity. Imports are expected to continue to supply more than half of the US requirements.

Jan 1, 1997

By Y. Lin

The objectives of this investigation were to study the zeta potential characteristics of a Powder River Basin coal in water and to study the effects of zeta potential on the agglomeration of coal particles. The electrokinetic measurements show that the zeta potential of the coal is dependent on pH, temperature, coal concentration and contact time with water. The effects of various additives for changing the zeta potential of the coal were also evaluated. It was found that the strength of the coal agglomerates is increased when the zeta potential diminishes. Neutralizing the zeta potential enhances agglomeration. Therefore, it is important to control the zeta potential of coal to achieve optimum performance in coal-particle agglomeration.

Jan 1, 1997

By R. J. Pruett, J. Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1999

By Mark W. Cadwallader

Heap leach mining requires liners in order to contain leaching solutions for both economic and environmental incentives. The use of HDPE geomembrane liners for heap leaching is discussed in this paper. Comparison is made to clay liners, with inclusion of economic considerations. Several heap leach projects incorporating geomembranes are discussed.

Jan 1, 1987

By V. L. Magnus

The text of this chapter was not received in time for printing.

Jan 1, 1979

By Philomene Verlaan

The Code for Environmental Management of Marine Mining (the Code) was adopted in 2001 by the International Marine Minerals Society (IMMS) following extensive and wide-ranging consultation, and updated in 2002. The Code provides a framework and benchmarks for development and implementation of an environmental program for a marine exploration or extraction site by marine mining companies, and for stakeholders in governments, NGOs and communities in evaluating actual and proposed applications of environmental programs at marine mining sites. The Code provides for its review by IMMS after five years, with a focus toward possible modifications based on experience with its implementation and in light of developments in the field of marine mining and associated environmental practices, in consultation with the marine mining industry and with other stakeholders at marine mining operations. As the review of the Code is now due, to begin the process, this paper will present an analysis of the Code and initial suggestions for its modification. Keywords: marine mining, marine environment, sustainable development, marine environmental risk management

Jan 1, 2008

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material's flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By Nancy L. Jackson, Leslie C. Thompson

Acid rock drainage is one of the most complex issues facing regulators and mining companies for management and remediation of mining wastes. All mining waste units, including open pits, underground workings, tailings, waste rock and leached spent ore have the potential to generate acidic leachate based on the acid generation or neutralization potential of the material. This paper uses a case study of the Walker Mine in northern California to give an overview of the available control and mitigation methods. Wetland design is emphasized as a low-cost alternative treatment option for wastewater remediation. The Walker Mine is located on the eastern flank of the Sierra Nevada, 20 miles north of Portola in Plumas County, California. The Walker Mine was an active copper mine between 1915 and 1941. During active mining, tailings were discharged into an area 1 mile west of the site at the confluence of Dolly Creek and Grizzly Creek. In addition, there were two main sources of metal-rich, acid waters impacting Dolly Creek: discharge from the mine tunnel portal, and seepage and surface runoff from waters contacting mine waste downslope from the portal area. A mine portal seal was installed in 1987 which prevented the majority of mine water drainage from further contaminating the area. Minor drainage from the portal and seeps discharge into a holding pond which overflows into Dolly Creek when elevation exceeds 6,200 feet. A site characterization study was performed to evaluate the potential water quality threat to Dolly Creek from mine tunnel discharge and waste rock seeps. Based on the results of this study several remedial options were investigated, both on a design and cost basis, to determine which abatement alternatives could be realistically implemented. The remedial options considered include both in situ containment (landfill, waste pile) or removal (backfilling into underground workings and/or sinkholes) of solid wastes. Waste water remedial options include long-term, seasonal treatment of the portal mine water, or long-term, passive treatment of portal discharge and waste pile leachate.

Jan 1, 1993

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By C. G. Bock

Geologic profiles constructed from exploratory drill holes gave basic geologic information for bidding on 4913 ft. of twin rock tunnels under the Potomac River. To provide additional geologic information for construction, tunnel faces and shafts were mapped throughout excavation. This information was plotted in plan and section so that geologic structure could be projected ahead and prediction of conditions could be made. In structurally complex areas, 3-D models were made and used to show the geologic structure. Core from exploratory drill holes was relogged and structure oriented with that found in the tunnels to make the ultimate use of the core and refine the geologic picture. As excavation proceeded, geologic mapping showed that the projection-prediction approach was useful and essentially correct.

Jan 1, 1974

By Martin C. Jones

INTRODUCTION This paper outlines the methods used to drill and pregrout prior to the excavation of five Mine Shafts in the Coal Measures of the Eastern United States. One example is the use of cement pregrouting of four 240 meter deep shafts and the second is the use of chemical pregrouting of a 360 meter deep shaft. These two examples will be compared and contrasted, both at the investigation stage of each project, and during the drilling and pregrouting itself, to illustrate the different approaches taken and how these affected the outcome, both technically and economically. INVESTIGATION FOR 240 METER SHAFTS In the case of the four 240 meter shafts, site investigation was carried out prior to bid, and information was made available by the Client in the form of a report. This report was based on pressure testing of NQ cored boreholes at each shaft site. Pressure testing was repeated two or more times, at each test setting, using 345 or 690 kPa of water pressure in accordance with the procedure outlined by the U. S. Bureau of Reclamation. Flow readings were taken every minute over a period of ten minutes. Maximum computed permeabilities, for the strata which accepted water under test for the shafts, carried between 1.0 x 10-6 m/s and 3.0 x 10-6 m/s, and total calculated seepages varied between 170' litres/minute to 3891 litres/minute. Although these figures did not indicate an excessive amount of seepage, the Client decided that pregrouting should be carried out, and chemical grouting was not discussed, even though the test permeabilities indicated the use of cement grout would be limited in this case.

Jan 1, 1979

By Chris Joyce, Peter Ryan

Investigation of the occurrence and significance of acid drainage from mine sites in Australia has received a degree of attention in recent years. For contemporary and future projects, particularly those in hi1;1her rainfall areas, the focus on prediction and resolution of acid drainage issues is. likely to increase. This paper describes the preventative and remedial measures adopted at three metalliferous mines in northern Australia at which acid drainage was identified as a key issue with respect to project environmental management and rehabilitation. The thre case studies respectively comprise an active, ·1 recently decommissioned and an abandoned operatiou which was rehabilitated in the mid '80s.

Jan 1, 1991

By M. Rieber

In July 1985, as the U.S. copper industry contracted and the Mexican industry expanded, a trans border pollution agreement was signed which included smelter air pollution control in the "Gray Triangle": Cananea, Nacozari and Douglas. Since then the Douglas smelter has been closed, a year earlier than initially required; though its new smelter is operating, S02 collection and acid disposal at Nacozari is yet to come; and the Cananea smelter has been un-touched. Nacozari and Cananea copper mining have expanded while a reduced U.S. copper industry has rationalized to a point of fragile profitability. As a paradigm of U.S. copper competitiveness, this paper attempts to explain the differential fortunes of copper in the two countries, to project the future of the smelter agreement as a function of acid disposal, and to consider the consequences of the politicized application of smelter pollution control in Arizona.

Jan 1, 1988

By Robert G. Beverly

INTRODUCTION Standards limiting the annual exposure of United States uranium miners to radon daughters were established in 1967 at 12 Working-Level-Months (WLM). The standard was reduced by a factor of three, to 4 WLM, in 1971. Currently, the standard is again being examined to determine if it should be changed. Since 1967, Union Carbide has calculated individual monthly exposures in company and contract-operated mines located on the Colorado Plateau. Although it has been possible, by extensive ventilation control measures and accurate routine sampling, to meet the current exposure standard, there are many miners whose exposures closely approach the 4 WLM standard for any given year. However, it was noted that for miners who work for any extended period of years the [average] exposure was much less than the standard. The primary purpose of this paper is to show that, in effect, any annual exposure standard to radon daughters results in a long-term exposure considerably below that standard. Further, most miners, due to their job assignments and/or employment habits, only receive a small fraction of the standard. HISTORY OF EXPOSURE STANDARDS Prior to 1967, radiation protection in uranium mines was fundamentally based on a radon daughter concentration guide. In 1960, the American Standards Association published mine and mill radiation protection standards (ASA-1960). The Colorado Department of Mines, in 1961, adoped a standard which followed the ASA Standard and provided that if concentrations exceeded 10 Working Levels (WL), the area was to be shut down until corrective action was taken; if between 3 and 10 WL, corrective action was to be initiated; between 1 and 3, additional samples were to be taken and individual exposures evaluated; and if below 1 WL, conditions were considered to be controlled. In 1967, the U.S. Department of Labor issued the first exposure standard which called originally for limiting annual exposures to 3.6 WLM but which was later changed to 12 WLM. The complicated regulatory developments leading to this standard have been described elsewhere (Beverly-1969, Rock & Walker-1970). Effective July 1, 1971, this exposure standard was lowered to 4 WLM per year, which is the current standard. Over the past year, there has been speculation about the potential risk to uranium miners working at the present standard. A recent NIOSH Study Group Report (NIOSH-1980) concluded: "There is also strong evidence that a substantial risk extends to and below 120 WLM of exposure." The 120 WLM corresponds to a miner working in uranium mines for 30 years, a rare occurrence, at an exposure rate of 4 WLM per year, an even rarer occurrence. On the other hand, the General Accounting Office, in a recent Report to the Congress (GAO-1981), was very critical of reports by NIOSH on general low-level radiation risks. The GAO recognized that”...important questions remain unanswered about the cancer risks of low-level ionizing radiation exposure;" and recommended that Congress enact legislation giving statutory authority to an interagency committee to coordinate Federal research on health effects of ionizing radiation exposure. The International Commission on Radiation Protection at its March, 1980 meeting recommended limiting the inhalation of radon daughters to 0.02 J per year, equivalent to 0.4 WL, which on an annual basis would be 4.8 WLM and noted it is common to reduce this figure by 20% for allowance in the case of uranium miners for external and/or dust exposure(Sowby-1980). This is essentially equal to the present standard of 4 WLM. As earlier uranium miner exposure studies are reevaluated, and as new studies are conducted, it is important that the relationship between regulatory standards and the resulting actual exposures be recognized. UNION CARBIDE URANIUM MINING EXPERIENCE Union Carbide started mining Colorado Plateau uranium-vanadium ores in the late 1920s for the contained vanadium values. In the early 1950s, the Atomic Energy Commission contracted Union Carbide to produce uranium at mills located in Uravan and Rifle, Colorado. The company now has over fifty years of mining experience in the area. Some mines are operated as company mines and others are operated by private mining companies under a contractual arrangement. Ventilation, sampling, and exposure calculations are carried out the same in contract mines as in company-operated mines. Data presented in this report do not differentiate between company or contract employees and include all employees who worked underground any portion of a year in Union Carbide mines from 1967 through 1980. At the peak of uranium mining activities in 1970, there were 577 miners employed at year end (285 company employees and 292 contract) and 52 mines in operation (8 company-operated and 44 contract mines). Contract mines varied from two-man operations up to 15 employees. Company mines were generally the larger operations and employed from 20 to 100 miners.

Jan 1, 1981

By Serkan Saydam, Ercument Yalcin

This paper presents the results of Caldagi Nickel-Cobalt Ore Deposit's, located in Turkey, reserve and ultimate pit limit design analysis. Reserve analysis of any deposit requires two steps. First one is to constitute of block model of the deposit and second step is to generate ultimate pit limit. The block model of the Caldagi ore deposit has been created by means of geostatistics. The reserves of nickel and cobalt in this block model are defined as resource, approximately 12 million tons of nickel and 1 million tons of cobalt with average grades of 0.9% Ni and 0.03% Co, respectively. Ultimate pit limit analysis has been performed by considering economic, technical and legal factors. In this paper, the ultimate pit limits are generated by Lerchs & Grossmann (L&G) algorithm. As a consequence of ultimate pit limit design, total amount of tonnage to be excavated is 1.4 billions of tons, 700 million of which contains ore and 747 million of which is the tonnage of waste.

Jan 1, 2002

By Angelus S. C. Owili-Eger

The protection of groundwater resources is a growing issue on both the legislative front and within the private sector. At present, the legislative push is to establish within the Environmental Protection Agency a comprehensive research, development, and demonstration program relating to groundwater contamination and resources. It is evident that certain aspects of such legislation will be directed at the mining industry. Consequently, the mining industry must position itself to address the issues and concerns from a backdrop of facts and knowledge by developing an integrated hydrogeochemical model of the mining environment.

Jan 1, 1989

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By Terry Mattioli, Buck Bradshaw, Terry Fagg, Larry G. Nisle

Deposition of calcium carbonate scale on activated carbon in the Pinson Mining mill carbon column circuit was causing erratic gold recovery rate, long acid wash time, high carbon attrition and long strip times. Continuous addition of a blended antiscalant into the mill thickener overflow at 8 ppm reduced the average carbon acid wash weight loss from approximately 10% to < 2%. Cleaner carbon improved the gold loading rate in the mill column. The loading on Column I was increased to 175-225 oz/ton carbon from 125-150 oz/ton for a two-day carbon advance cycle. The higher loading capability has given Pinson more flexibility and better control of gold flow through their carbon adsorption, stripping and electrowin­ning processes. Preventing calcium carbonate build-up on activated carbon with this antiscalant reduced acid wash batch time. This enabled Pinson to acid wash and regenerate every batch of stripped carbon for all the adsorption circuits. Shorter strip times have also resulted from the lowering of the calcium carbonate scale level in the loaded carbon. Carbon consumption has been reduced and is now averaging 0.046 lb/ton ore for the first six months of 1990 compared to 0.072 and 0.083 lb/ton respectively in 1989 and 1988.

Jan 1, 1990

By K. Hanumantha Rao, K. S. E. Forssberg

The limestone deposit of Gâsgruvan, Sweden contains around 89.2 per cent of calcite. Conventional and column flotation studies have been carried out using sodium oleate and modified fatty acid collectors in the presence of sodium silicate modifier. The effects of collector and silicate concentrations, and particle size on the flotation response of calcite have been investigated. The results have been discussed in comparision to the performance of conventional and column flotation cells. The feed size is found to be a significant factor to achieve a high grade calcite concentrate either by conventional or by column flotation. The loss of selectivity at fine particle sizes is examined using a modified DLVO theory.

Jan 1, 1995