Search Documents

By R. K. Mehta

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated for a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1989

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

By Joseph Corvetti

This paper is of conceptual nature. The authors present their idea of creating an integrated and intelligent excavation design system. Research work has just been started and the results will be addressed during presentation of this paper. The authors are currently engaged in a pilot study and expect to build a feasibility prototype expert system (establishing the numerical-cognitive coupling in excavation design) by the end of this year.

Jan 1, 1996

By A. H. Hassan

Stibiotantalite is a relatively rare mineral not commonly found in the major tin districts of the world, and its separation characteristics have not been documented adequately in the literature.

Aug 1, 1979

By Pieter C. van Aswegen, J. A. Brierley, C. L. Brierley

The bacterial-oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery is marketed by BlOMlN Technologies S.A. The process was originally developed by GENMIN who is still providing testwork, design and commissioning assistance to BIOMIN. Since 1986 three BIOX® plants have been commissioned by GENMIN. A further two plants will be commissioned during 1993 and 1994. The commissioning and operational experiences from these plants are described in the paper.

Jan 1, 1993

By Yiyin Ma, Yuqi Chen

Based on two in-situ measurements and mathematical analysis, the micro-climate in a large central underground pump and power station has been discussed in this paper. It is found from the research that the "semi- infinite" body model in the general heat transfer can closely represent the heat exchange process in the air flow-surrounding rock-adiabatic intermittent heat source complex in the station. Finally, computer simulations were made to calculate the micro-climate in a similar pump and power station where power machines operate intermittently. The simulation results are quite satisfactory. It can provide useful information for decision- making in the air conditioning of such stations.

Jan 1, 1991

By Robert Snow, Yingxue Yu, Howard Hanson, Patrick Zhang

One of the major current efforts by the Florida phosphate industry to reduce deep aquifer water consumption is to use 100% recycle water for flotation. This measure alone could save billions of gallons of deep well water annually. However, this also results in higher suspended solids (slimes) in flotation water, causing poor process performance particularly for amine flotation. Polymers could play a major role in allowing the industry to use high-turbidity recycle water for amine flotation without compromising its impact on the Florida economy. The enhancement of rougher flotation by polymers may also have potential. Most importantly, dramatic efficiency improvement may be realized by floating silica first. Adding polymer to flotation feed and/or water is perhaps the most economically viable way of reversing the Crago "double float" process, in order to reduce operating costs and increase phosphate recovery. This paper presents both laboratory and pilot flotation data showing the effect of different polymers on collector dosage and flotation recovery. There appeared to be an optimal range of polymer concentration beyond which the benefits do not offset the drop in phosphate recovery. The effect of poly mer is slime-level dependent. Pilot testing data show that the "Reverse Crago" process (floating silica first followed by phosphate flotation) can outperform the Crago process.

Jan 1, 1999

By S. Hardcastle

Kidd Creek mine has recently completed upgrades of its primary ventilation systems enabling it to maintain a delivery of 1200 m3/s to continue mining ore zones extending to over 3000 m below surface. Following these upgrades the mine initiated a multi-stage review of their ventilation usage. The focus of these reviews, ranged from a brainstorming session of invited experts, through an evaluation of production plans to a detailed analysis of production data to determine if the ventilation system could be run more efficiently, thereby reducing the mine?s power consumption and associated operating costs. The initial review identified 1500 kW of installed fan power that could be eliminated from the primary ventilation system. The benefits of the subsequent analyses, so far, are not as measurable. The second and third analyses, respectively using long range production plan data and historic production data to determine ventilation requirements based upon diesel equipment, did not agree. Both were shown to have limitations, the future based analysis underestimating, and the historical analysis overestimating the requirements. Regardless of the failings of each method, important outcomes were achieved from the detailed analyses, namely, the ability for a mine to meet a forward analysis prediction of airflow depends on its ability to adjust the ventilation to meet the dynamic nature of the mining process. Also, to minimize total ventilation requirements, a mine must regularly redistribute its airflow; this not only reduces the total volume requirement but also increases the variability of the delivered flows which can provide further operational savings. Since the detailed analyses, the Kidd Creek mine has implemented a more frequent ventilation review and redistribution procedure; consequently, it now operates with an average delivery of 930 m3/s, which is 23% lower than in 2005 at the start of the review process.

Jan 1, 2009

By Joe Maloney, Steve Shadow

Mining conditions at Cyprus Amax's Twentymile Coal Company (TCC) require the use of regenerative conveyors. Regenerative conveyors were first used in the Southwest Mine District and then in the challenging East Mine District. This paper will discuss the development and refinement of the equipment used to brake the regenerative conveyors.

Jan 1, 1998

By T. M. Jones

This paper outlines the development of the theory of controlled district recirculation and indicates the advances in understanding and technology which have enabled a major change in established ventilation practice. An insight is presented into the possible future use of controlled district recirculation as acceptable practice in mine ventilation planning.

Jan 1, 1987

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

In 1991, US mine production of barite decreased 3.4%. Barite consumption, sold or used by grinding plants, decreased by 11.7%. Imports also decreased by 15.4% over 1990. World mine production increased I%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, increased 3.3% according to the Bureau. The declared value c.i.f. US port of all imported crude barite during 1991 increased from $40.61/t ($36.84/st) in 1990 to $42.35/t ($38.42/st), the Bureau stated. Nevada was the leading producer of barite with 78% of the total, followed by Georgia and Missouri. It is estimated that 75% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 93% was used in drilling fluids. The remaining 7% was in the non-oilfield sector, including barium chemicals and fillers in paper, plastics and glass. Tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1990. The average number of rotary rigs operating was 860. That was 14.9% less than the 1990 average of 1010 in the US. Crude barite imports were 138 kt (152,000 st) less than 1990 or 15.4%. Imports accounted for 70% of the (ap¬parent) barite consumed in the US. During 1991, China continued to be the leading exporter of crude barite ore to the US with 85.1 %. India followed with 14.8%. About 97.5% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 56.7 to 46.2 kt (62,500 to 51,000 st) 1991. Mexico was a major exporter to the US, accounting for 75.3% of the total ground barite imports. Canada shipped 23.7%, while other countries accounted for less than 1 %, primarily for the nonoilfield market. During 1991, the number of grinding plants supplying the drilling fluids market along the Gulf Coast was reduced from 12 to 10. Baroid Drilling Fluids completed its mining program at the Rossi Mine near Dunphy, NV.

Jan 1, 1992

By Claude Bazin, Robert Grant, Mike Cooper

An analysis of the Pb recovery as a function of particle size was carried out for the CuPb rougher bank of a complex sulphide mineral processing plant. Results indicate that higher recovery may be achieved by optimizing the flotation feed size distribution. Simulation of the actual grinding circuit has provided guidelines to modify circuit operating conditions in order to improve product size distribution. Plant tests ar

Jan 1, 1991

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

By Patrick G. Hill

This paper discusses safety protocols for Kiewit Construction’s Level (3) project. The Level (3) project will cover a majority of the United States, and literally thousands of site operations will be conducted over a wide geographic area under challenging conditions; rivers, roads and other features, both from the surface and often for great and from boring pits. Developing a progressive safety plan for fast-track linear projects using micro-trenching and directional boring techniques requires significant investigation, planning and evaluation. Safety protocols for inner duct installation, to be accomplished with extensive use of directional boring is an essential part of the safety plan for network construction. In light of the shear volume of work and the geographical extent of this project, in many different types of terrain, this paper will identify approaches to safety applicable to fast-track linear projects, whether surface or underground-based. Establishing a safety culture into all aspects of this operation will improve productivity and cut unnecessary expenses. This new approach involves continual improvement and evaluation of hazard analyses, inspection procedures and training.

Jan 1, 1999

By Nathan Brandner, Denise Levitan

For many decades, a potash operation in Saskatchewan, Canada, has maintained storage impoundments for mine tailings and process-related mine water. The mine water is a concentrated aqueous solution, with most of the total dissolved solids (TDS) consisting of sodium and chloride. Although the facility has a system of slurry walls and collection/ diversion ditches, the mines monitor the surface water and groundwater around the tailings storage facilities (TSFs) for releases. Groundwater on the western side of the facility has been measured as having concentrations of TDS, magnesium, sodium, chloride and sulfate above provincial drinking water quality objectives. In addition, electromagnetic surveys have shown high electrical conductivity in that area. For these reasons, studies were undertaken to investigate the extent of the high TDS concentrations in groundwater and whether the elevated concentrations were related to the TSF. Chloride and TDS concentrations in groundwater monitoring wells were used to interpret the transport of high-TDS mine water moving along three interpreted zones of elevated TDS west from the facility (Fig. 1). The zones of elevated TDS concentrations corresponded to the areas of high conductivity identified by the geophysical surveys. These results suggested that mine water could be emanating from the TSF and potentially require remediation. However, the interpreted orientation of the high-TDS groundwater and apparent flow paths were perpendicular to the direction of groundwater flow in the area. The fundamental conflicts in these interpretations led to a reexamination of the conceptual site model for the distribution of potential mine water releases. Although the data examination and visualization made it clear that TDS concentration alone was not a reliable indicator of mine water release, there was still concern about elevated chloride concentrations. To further evaluate high TDS and chloride concentrations, several background area wells were installed northwest of the facility, beyond where mine water impacts could occur (Fig, 2). The background wells had highly variable chemical compositions. One of the wells had an elevated TDS concentration with magnesium and sulfate as the dominant ions with chloride concentrations above drinking water objectives, similar to the high-TDS wells west of the facility. The results of the background groundwater investigation (major ion chemistry) were supported by the scientific literature on prairie sloughs throughout the North American Great Plains. These sloughs are small, shallow and sometimes seasonal wetlands found throughout the region. Seasonal cycling in precipitation/ runoff and evapotranspiration result in accumulation and mobilization of salts, especially sulfate-bearing phases such as gypsum. The long-term dynamics of these features, which are common on the property west of the facility, likely control the TDS concentrations and compositions in shallow groundwater rather than mine water migration from the site. The conclusions from this investigation led to a better understanding of the lateral distribution of potential TSF-related impacts versus background groundwater chemistry. Presentation of the data, including the visualizations of different water compositions, to the provincial regulatory agency representative allowed the facility to propose an optimized annual groundwater monitoring plan with reduced sampling frequency and annual sample count. This study underscores the importance of critical evaluation and comparison of various data types, including background levels, from a particular site and the iterative approach to developing and supporting robust conceptual site models for optimizing project outcomes.

Jul 1, 2025