Search Documents

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

By G. Kosick, G. Dobby

CEET, an acronym for Comminution Economic Evaluation Tool, was jointly developed by MinnovEX Technologies Inc. and 13 major mining companies for the purpose of designing and predicting the performance of grinding circuits. It fundamentally differs from other methods by using as its’ data set a geostatistically significant population of hardness data distributed across the mine block model. Historically the characterization of an orebody for the purpose of either designing a grinding circuit or predicting the performance of an existing circuit has been done with a relatively limited number of discrete samples. In addition to power selection, shell sizing, and costing for multiple circuit options, CEET also outputs tons per hour, P80, and operating cost on every mining block for subsequent integration back into the block model. This paper will provide an overview of what CEET is and how it works.

Jan 1, 2001

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975

By A. Cecala, J. Noll, J. Organiscak

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (minimum efficiency reporting value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50% of the DPM, a MERV 16 filter collected 96-98% of the DPM and two HEPA (high efficiency particulate air) grade filters captured over 99% of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90% effective in removing DPM, except under certain operating conditions when the efficiency was as low as 41%. A possible reason for the low efficiencies is an open window in the cab, but more studies need performed to obtain a better understanding of the cause and solution of the problem.

Jan 1, 2011

By William J. Shampine

The Floridan aquifer, which underlies all of Florida, yields water with a sulfate content of less than 50 parts per million in the north-western part and throughout most of the center of the State. In the southern part of Florida and along the most of the east coast, the sulfate concentration generally exceeds 100 parts per million and is as much as 1,700 parts per million. The sulfate concentration tends to be higher in the deeper zones of the aquifer. This map shows the sulfate concentration in the upper part of the aquifer. Sulfate is found in almost all natural water. Sulfate in rainwater is dissolved from impurities and gases in the atmosphere. Rankama and Sahama (1955, p. 314) report that the average sulfate content of rainwater is two parts per million; however, concentrations have been as high as 283 parts per million. Much of the sulfate in rainwater comes from hydrogen sulfide gas which is generated in shallow water on the continental shelves. The combustion of bituminous coal used for heating and industrial purposes seems to be an important local source of sulfate.

Jan 1, 1966

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the U.S. mining workforce who are potentially exposed to RCS [1,2] as various ore bodies are drilled, blasted, hauled by truck, crushed, screened/sized and transported to their destinations. To examine a method for assessing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on 80 miners across seven unique mining sites. The data were then collated and partitioned using a thresholding scheme to determine exposures that were in excess of 10 times the mean exposure for that worker. Focusing on these short-duration, high-magnitude exposures can provide insight into implementing controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20 percent or more by reducing exposures that occur during just 10 minutes of work per eight-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By Aram Grigoryan

This paper addresses historical aspects and construction sequencing of the subway complex under Columbus Circle in Manhattan; the structural elements of the rehabilitation and new construction; and the challenges associated with design and construction. PB is providing engineering services to New York City Transit (NYCT) for the rehabilitation of the 59th Street/Columbus Circle Station Complex that services over 150,000 customers daily. The project involves structural repairs, modifications and new construction requiring underpinning and temporary supports, custom framing details, and construction staging procedures to meet stringent limitations within the operating transit station and around the Columbus Circle street intersections.

Jan 1, 2008

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM)/Hatch Mott MacDonald (HMM) joint venture has been engaged by the New York City Economic Development Corporation (NYCEDC) to provide engineering ser-vices in connection with the replacement of two existing siphons which cross New York Harbor between Staten Island and Brooklyn. The project involves the construction of a 72-inch diameter pipeline within a 12-foot diameter tunnel beneath the New York Harbor. The tunnel will be constructed using either slurry or an earth pressure balanced (EPB) tunnel boring machine (TBM). This paper presents the results of an extensive geotechnical field and laboratory testing program including advanced frozen soil tests (uniaxial compressive strength tests, triaxial tests, and uniaxial creep tests), in-situ vane shear and pressure meter testing, and a marine geophysical survey (seismic reflection technique) to ascertain the complex subsurface conditions along the tunnel alignment and shaft locations. The paper will also discuss the design and construction aspects and the challenges associated with each component of this project.

Jan 1, 2008

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By R. A. Limons

Natural ores, sinters, and pellets were subjected to a carbon monoxide reduction-disintegration test under laboratory conditions including a simulated blast furnace gas and a 1000°F temperature. The most significant findings were that: 1. Self-fluxed pellets broke down to a greater extent than either the acid pellets or the acid or self -fluxed sinter. 2. When pre-reduced, both the acid and self-fluxed pellets had very good resistance to breakdown.

Jan 1, 1964

By Daniel E. Walsh

A pilot scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2"), crushed ore from Ester Dome, Alaska. 9.04 tonnes (9.94 tons) of crushed ore were sampled and processed through a Pan-American jig -Wifley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/tonne (22.4 oz/ton). The feed grade to the plant was calculated at 1.71 g/tonne (0.050z/ton). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/tonne (0.042), 1.30 g/tonne (0.038), and 5.47 g/tonne (0.16 oz/ton) respectively. Significant, coarse, free milling gold values were shown to remain in the jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1991

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Gary Tomaino, Specialty Minerals Inc., is the chair of the SME industrial minerals technical committees. Technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals as well as sorbents, filter and process aids. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •William Langer, U.S. Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2003