Search Documents

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By Barton G. Stone

"Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole," (Baxter and Parks, 1939)."An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence, the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence."The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling."Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive." (McKinstry, et al., 1948).In an actual orebody, the accuracy of sampling depends not only on the number of samples but also on their proper distribution throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore, it is important to select the places in such a way that all parts of the orebody will be represented."

Jan 1, 2014

By R. L. Guerguerian

Critical fasteners are described as they apply to the specification, manufacture, and assembly on large grinding mill bolted joints. The importance of adequate design methods, related joint diagrams and pivot analyses, and special emphasis on the quality of manufacturing and the tightening procedures in the field, are discussed; all in an effort to ensure high availability plant operation.

Jan 1, 2001

By Jacques Bernazeaud

Rouez is a recent discovery of a major low-grade sulfide body (± 100 m, 0,6 % Cu, 0.3 % Pb, 1 ,5 % Zn, 21 g/t Ag, 1.5 g/t Au) in a populated farming area of Brittany, France, some 30 kilometres northwest of Le Mans. The discovery is the result of an airborne electro- magnetic (INPUT) survey. It is the first time that the INPUT method has been used in France. The survey Gas successful in spite of the numerous interferences normally found in populated areas. The lack of a good drainage system would not allow the discovery of Rouez using stream sediment geochemistry alone. Ground geophysical surveys confirmed the airborne work and gave sufficient information to make the first hole a discovery hole. The deposit is Proterozoic in age and sediment-hosted. The metamorphism is low grade.

Jan 1, 1983

By J. H. Field

The sulfur dioxide emitted in low concentrations in flue gases from the combustion of sulfur-containing coals and fuel oils is a significant factor in contamination of the atmosphere with sulfur dioxide. A review of methods for treating gases containing high concentrations of sulfur dioxide shows that they are seldom satisfactory for purifying flue gases. Processes developed specifically for treating flue gases using liquid absorbents are costly and may cause localized pollution, because the cooled flue gases can settle in the vicinity of the stack. Bench-scale research is being conducted to investigate the use of dry absorbents for sulfur dioxide removal at temperature levels of about 250°- 300° F. and 600°-650° F. Alkalized alumina has been found effective for treating simulated flue gas and Is regenerable by hydrogen, carbon monoxide, or producer gas. Other metallic oxides have been tested as absorbents also. Chemically impregnated activated carbons removed sulfur dioxide from the gas at 265° F. Vanadium pentoxide is effective as a catalyst for oxidizing of sulfur dioxide in the simulated flue gas at temperatures lower than have been used commercially for gases with higher concentrations of sulfur dioxide. Conversions of sulfur dioxide to trioxide wore studied as a function of temp- erature over a range of about 570° to 750° F.

Jan 1, 1959

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By H. EI-shall

In this paper, the results of bench scale testing of five different flotation processes to separate dolomite from phosphate are discussed. The effectiveness of each process interms of phosphate recovery and MgO content in the concentrate is used together with the reagent consumption as the basis of comparison. The water quality is found to play a major role in the performance of these processes. Effect of water hardness as well as other parameters are discussed.

Jan 1, 1995

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

The latest in mining technology and equipment will be show-cased this month at MINExpo International 2004. The event, billed as the world’s largest mining equipment exhibition, is set for Sept. 27-30at the Las Vegas Convention Center. MINExpo, sponsored by the National Mining Association (NMA), is held every four years in Las Vegas, NV. This year’s event is expected to attract more than 40,000 mining industry professionals and executives from around the world. And several key members of the U.S. Congress and other senior government officials are expected to attend. In addition, senior industry and government officials from Asia, Europe, Australia, Africa and South America will be on hand.

Jan 1, 2004

By P. Sangurmath, C. Gundewar, M. Riyazulla, V. Vasudev, N. Shadaksharswami

Dharwar craton in the southern Indian shield, comprises the Neoarchaean foreland in the west and a relatively younger accretionary complex composed of granitoids and intervening gold-bearing volcano-sedimentary belts. The Hutti schist belt hosting a major gold producing mine is situated in the northern part of the eastern Dharwar craton. It is a horse-shoe shaped structure comprising predominantly of pillowed metabasalt of tholeiitic composition with minor amounts of clastic sediments and felsic volcanic rocks. The belt is intruded on all sides by circular to tabular bodies of granites and granodiorite. Important gold deposits are located at Hutti, Hira-Buddini and Uti villages. Felsic volcanics in the Hutti belt occur as tabular bodies of quartz porphyry and breccia. Two of the gold-bearing reefs in the Hutti mine, Viz., Middle and Strike reefs are intimately associated with tabular sub-vertical sheets of mylonitic quartz-feldspar porphyry intruding pillowed metrabasalt. In Uti mine area, the felsic volcanics occurs as a tabular body. At Hira-Buddini, the felsic volcanic occur as a irregularly shaped sheet in pillowed metabasalt. Mineralogical and geochemical studies suggest that the felsic volcanic rock in Hutti mine area is a rhyolite and at Uti and Hira-Buddhini it is of dacite composition. Scheelite occurs as veins, veinlets, stringers and blebs along fracture planes of felsic volcanics in the Hutti mine area, whereas at Uti and Hira-Buddini it is insignificant. On the basis of spatial association of metabasalt and felsic volcanics and on geochemical grounds, we interpret that the felsic volcanics might have originated by the partial melting of basalt. REE patterns of the granite, granodiorite and metabasalt of Hutti are similar to each other indicating that they could be co-magmatic. However, REE in the Hutti felsic rocks is significantly higher than in Uti and particularly Hira-Buddini mine areas. The two felsic volcanic samples drawn away from the mineralized zone from all the three mine areas were analyzed for tungsten. In Hutti one sample assayed 0.15% and another 0.062%. At Uti, in one sample it assayed 0.056% and another less than 1 ppm, whereas at Hira-Buddini, it is less than 1 ppm in both the samples. The spatially associated basalt analyzed 23 to 235 ppm tungsten, whereas granites and granodiorites have very low (<1 ppm) tungsten. Therefore, the source of tungsten in the felsic volcanics of Hutti area could be traced to metabasalt. The absence of significant amount of tungsten in the felsic volcanic of Hira-Buddini could be attributed to the lack of REE enrichment compared to REE in Hutti and Uti felsic volcanics.

Jan 1, 2007

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By Per-Martin Sandgren

LKAB&apos;s ores have specific mineralogical properties that make them especially suitable for the production of super-grade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. Until 1978 the approximate assay was 71.2 % Fe and 0.45 % SiO2. Since then the assays have been improved by process modifications to approximately 71.5 % Fe and 0.20 % SiO2. Scope exists for still further improvement. In recent years the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.6 % Fe and 0.30 % SiO2. Other special products are under discussion. The Malmberget ores are also suitable for the production of high-purity direct reduction pellets with a SiO2 content below 1 %.

Jan 1, 1981

By F. Dieu, C. Laughton

CERN, the European Laboratory for Particle Physics, is, at present, constructing an underground tunnel and cavern network to house a Large Electron Positron (LEP) colliding beam machine. This paper describes the techniques adopted to permit the excavation and temporary support of the access shafts through a series of glacial moraines, at depths of up to 80 m, to reach the bed-rock. Owing to the presence of superficial and deep water-tables, the variable nature of the moraine deposits and, above all, the tight work schedule, a combination of diaphragm walling and ground freezing was employed.

Jan 1, 1987

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

Through-the-Earth (TTE) communication systems were developed to provide post-accident communication in underground mines. Unlike primary tracking systems, they do not require any major infrastructure installations underground. Instead, they use the Earth’s overburden as the medium or channel for the transmission of electromagnetic waves between surface and underground. Under ideal conditions, TTE communication systems should be able to provide full-duplex, two-way voice, text and data communication. However, this will depend on the design and optimization of the different types of TTE communication systems (that is, antenna and electrodes), and understanding of the rock properties and their influence on the transmission of signals. This can help simulate and model the transmission efficiencies and predict the possible range and data rates. Being able to optimize the performances of these systems can enhance rescue missions, improving the chances of saving trapped miners, and ultimately reduce fatality rates across the mining industry.

Feb 1, 2025