Search Documents

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001

By B. Devulapalli

A mathematical model of the industrial hydrocyclone based on fluid dynamics is a better alternative to the currently existing empirical models. The swirling-flow velocities are determined by solving the Navier-Stokes equations with an appropriate turbulence model. The solution of the momentum-balance equations yields the flow field inside the hydrocyclone which determines the particle trajectories, and subsequently the classification curve. The essence of the model is that the physical dimensions of the hydrocyclone and the slurry characteristics can be incorporated, and the influence of these parameters reflects on the flow predictions. The predicted tangential and axial velocities in a 250-mm hydrocyclone are in good agreement with the laser-Doppler velocimetry measurements. Finally, the predicted classification curves show good agreement with experimental data measured on a KREBS Dl0B hydrocyclone.

Jan 1, 1993

By E. C. Speers

The Ray Mines Division has a long and illustrious history beginning in 1911, as one of the early underground block caving copper mining operations. The tonnage mined from the beginning of operations, increased from about 8, 000 TPD in the early years to the present daily tonnage of 22, 500 tons, mined by open pit methods. The Ray basic milling practice has been relatively unchanged since 1927 when the sulphide-flotation process was introduced at Ray. The leach-precipitation-flotation process introduced in 1956 has been the only major process change. The change from underground to open pit' mining was accompanied by a renewed drilling and exploration program which developed large tonnages of low grade copper ores both in the porphyry and the diabase. The ore bodies as outlined were of such a grade and size that it soon became apparent that economical operations could not be developed with the lower tonnage rate. Also that in order to develop these newly proven ores, it would be necessary to move the Ray crushing plant, the Ray. supporting shops, offices, a substantial part of the Ray townsite, and would also involve the rerouting of Mineral Creek, a typical Arizona stream which is dry most of the year but can flow as high, as 8, 000 second feet in the rainy season. This paper describes those changes in flow sheet made necessary both by the increased tonnage .and the requirement to move as much of the crushing facilities from the Ray area as practical in order to free the mine for the extension of its physical limits.

Jan 1, 1961

By J. Hunter

The Highland Uranium Project in Wyoming is an in-situ leach (ISL) facility owned and operated by Power Resources Inc. It is the largest uranium producer in the U.S. and the largest uranium producer by ISL in the western world. With its limited capital investment and low operating costs, the ISL technique has been demonstrated to be an effective and environmentally sensitive method for recovering minerals from these low grade and otherwise uneconomic orebodies.

Jan 1, 1996

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By E. Finch

Beneficiation tests were conducted on samples from three ore zones in the Los Monos, Navay orebody in Táchira State, Venezuela as part of an overall feasibility study. The scope of work included ore sample characterization, flowsheet development, and optimization of beneficiation variables on a bench scale followed by confirmation on a pilot plant scale. Phosphate in the ore samples occurred primarily as francolite and was associated with quartz, kaolinite, and feldspar. Liberation of the phosphate began at 589 microns (28 mesh) for the main ore zone sample and at 295 microns (48 mesh) for the lower-grade ore zone samples. Development tests on simulated mining composites demonstrated that the samples responded well to 589 micron (28 mesh) grinding, two stages of high intensity scrubbing, conditioning at high % solids with caustic and equal amounts of tall oil and fuel oil, and separate coarse and fine flotation circuits with one stage of roughing and two stages of cleaning (reflotation). Concentrates in the range of 31.5-34% P205 with recoveries from 64-70% were obtained from the mining composites. Product quality for all concentrates in the range of 31.5 % P205 was good; 1.40 CaO/P205 and 0.04-0.05 minor element ratios. Confirmation testing in a continuous pilot plant produced results similar to those achieved in the laboratory.

Jan 1, 1993

By A. S. Speirs

Over the last few years, the never-ending search for mineral wealth has taken the exploration efforts of Canadian mining companies further and further into the High Arctic and isolated locations where regularly scheduled transportation and communication facilities are nonexistent. Names such as Black Angel, Nanisivik, Asbestos Hill, New Quebec Raglan, Rabbit Lake, and Arvik are today frequently mentioned in mining publications. Twenty years ago, mining in these locations was unheard of, mainly due to logistic problems. However, improvements in the design and use of helicopters, STOL aircraft, and icebreakers in northern areas have helped to overcome these problems, making these locations more attractive to mining companies. Since 1969, when Redpath completed its first Arctic project at Texas Gulf's Scrathcona Sound property on the northern tip of Baffin Island, Redpath has been actively involved in contracting and engineering projects in three general areas: the High Arctic, Ungava and Greenland. A map showing some of these projects is shown in Figure 1. In these areas, permafrost conditions exist from a depth of 274 metres in Ungava to a depth of approximately 610 metres in the Little Cornwallis Island area, with rock temperatures ranging from -5°C to -13°C. Outside temperatures range from a low of -50°C in the winter to a high of 21°C in the summer. High winds in the winter result in wind chill factors lower than -73°C

Jan 1, 1980

By J. S. Gardner, J. J. Zaluski

I. INTRODUCTION West Virginia has a long history of coal production.1 The state at one time led the nation in total coal production, while at the same time coal from West Virginia constituted one quarter of total U.S. coal production.2 In more recent years, however, West Virginia’s level of coal production has been reduced in comparison to that of other states due to the high relative cost of producing coal in the state.3 Another blow to the producers of coal in West Virginia is the action known as Bragg v. Robertson.4 In 1998 various individual plaintiffs, as well as a conservation group known as the West Virginia Highlands Conservancy, filed a civil action under a provision of the Surface Mining Control and Reclamation Act of 1977, Pub. L. No. 95-87, §522, 91 Stat. 445 (codified at 30 U.S.C. §§1201-1328) ("SMCRA" or the "Act") that allows declaratory and injunctive relief against state and federal officials for non-compliance with the Act.5 The plaintiffs generally claimed that the Director of the West Virginia Department of Environmental Protection ("WVDEP") had exhibited a pattern of violating mandatory non-discretionary duties under SMCRA and the West Virginia state regulatory program.6 These non-discretionary duties involved many areas of regulation, including water quality standards, disturbance of wetlands, hydrologic reclamation plans, Approximate Original Contour ("AOC") requirements and AOC variances, post-mining land uses, contemporaneous reclamation, and as explained later, the "buffer zone rule."7 In addition to these claims against WVDEP, the plaintiffs also alleged that certain individual members of the Army Corps of Engineers (the "Corps") had failed to carry out statutory duties under the Clean Water Act (the "CWA") and the National Environmental Policy Act ("NEPA").8 Generally, the complaint stated that the Corps did not have statutory authority under the CWA to regulate valley fills created for the purpose of the disposal of waste material, i.e., the overburden associated with mountain top mining.9 Alternatively, the plaintiffs claimed that even if the Corps could regulate valley fills, the Corps violated NEPA by issuing nationwide permits without required analysis. Finally, the plaintiffs asserted that the issuance of a nationwide permit for surface mining valley fills is unlawful.10

Jan 1, 2001

By William J. Wasko

Maintenance of mining equipment has become so complex and important from a cost and product ion standpoint that the organization must be set up in an engineering fashion to be successful. Production costs are greatly affected by proper maintenance. Tonnages can only be met when operating time is at its maximum and breakdown time is at its minimum. Last, but equally important, large capital expenditures must be protected and improved The effectiveness of the maintenance program will, in many respects, be a direct, result of the effort put torch in developing the overall program. Once the need of maintenance is realized, the next step is to determine what the organization should be and what it should accomplish. Follow through is then most vital. Preventing machine breakdowns and reducing maintenance costs are the primary goals of all maintenance organizations. Good preventive maintenance, a system for inspecting equipment and a complete record of inspections will help attain these goals.

Jan 1, 1966

By J. L. Moreno, A. L. Williamson, R. D. Bartlett

Large open pit mines in desert climates, such as the Phelps Dodge Morenci copper mine in Arizona, can create groundwater cones-of-depression of considerable size and stability. The hydraulic containment provided by the groundwater depression prevents migration of process solutions into the surrounding regional aquifer. Copper leach operations that fall within the groundwater depression may not require costly lining if passive containment can be demonstrated. An approach is presented in this paper that was successfully used to demonstrate passive containment. The approach includes a combination of groundwater modeling and a water balance analysis of leaching operations failing within or immediately near the open pit.

Jan 1, 1999

By R. Hedin, M. Dunn

The Pennsylvania Department of Environmental Protection (US EPA 319 program) provided funding to aid a public-private effort in the installation of an environmentally-friendly system to treat abandoned mine drainage at Jennings Environmental Education Center (Pennsylvania Department of Conservation and Natural Resources). Through this cooperative effort among state and federal agencies, mining, excavation, and environmental companies, college and home school students, Girl Scouts, and volunteers, a successful multi-component passive system, readily accessible for upgrades and public education/research activities, was built. 90 people were directly involved in construction of this award-winning system and about 1000 people annually benefit from the educational opportunities.

Jan 1, 2002

By P. J. Miranda, C. G. Anderson, L. G. Twidwell

Titanium is a metal of increasing worldwide strategic importance. The Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech of the University of Montana is currently directing two titanium research initiatives. The first program, Titanium Extraction Mining and Process Engineering Initiative (TEMPER), is focused on producing low cost titanium through the identification and development of new mining, beneficiation and extraction technologies which will significantly reduce the cost of titanium production. This will directly benefit worldwide commercial applications. Secondly, CAMP is evaluating new technologies for fabrication of titanium utilizing the Free Form Titanium Fabrication (FFTF) initiative. These technologies may drastically reduce the cost and time to manufacture titanium components. Because of the high strength to weight ratio of titanium coupled with its superior corrosion characteristics, these programs will be of vital importance to expanding the commercial and strategic applications of titanium. An overview of these two new titanium initiatives will be presented in this paper.

Jan 1, 2005

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By Y. V. Swamy, B. Bhoi, H. S. Ray

Low-grade manganese ores with low Mn/Fe ratios can he enriched through selective carbon reduction of iron oxide to magnetite followed by magnetic separation o f the magnetite. Thermogravimetric analysis (TGA) was used to assess the preferential isothermal reduction of pure M1702 and Fe2O3 using solid carbon. This was followed by reduction of a synthetic analogue of composition comparable to an actual low-grade ore (i.e., Sandur manganese ore, Sandur, India). The carbothermic reduction of the manganese ore converts the hematite and goethite minerals to magnetite (Fe3O4), with the magnetite then going into the magnetic, fraction. The resultant nonmagnetic ,fraction becomes depleted of iron with an enhanced manganese content. These results show that it is possible to reduce the iron from 22% to 5.85%, thus increasing the Mn/Fe ratio from 1.52 to 6.2 with a manganese recovery of about 50%. The recovery was, further improved by grinding the magnetic fraction to -75 µm.

Jan 1, 1999

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004

By W. J. Douglas

Before discussing minicomputer software for the mineral industry, it is helpful to explain some of the computer program terminology. Most of the terms are the same as those applied to large computers. A computer system consists of a machine (hardware) with electronic and mechanical components and instructions (software) that define its operational logic and sequence. This logic is described by sets of commands grouped into programs. Each program has specific objectives related to the computer's operation and to production information from computer data that are input and processed. Software, therefore, is a general term applied to any type of computer program. Instructions to the computer are communicated through languages that convert logical and arithmetic statements into machine operations. The languages may consist of statements resembling mathematical or logical phrases understandable by humans, or they may be coded statements with no apparent resemblance to spoken language but readily understandable by the computer. Computers also translate higher level languages such as FORTRAN or COBOL into machine languages using other programs called Compilers. Programs written in these higher level languages are generally called source code. However, programs written in computer assembly language may also be called source code. The compiled version of the program after it has been translated by the compiler software is called object code. Programs used to "instruct computers how to be computers" are generally called systems software. They relate more to computer operation than to producing externally usable results. Programs producing information for many users-engineers, accountants, managers-are termed applications software. For the most part, applications software is the principal concern of the mineral industry. Programs are developed to fit user requirements as interpreted by programmers. Programs vary in quality, precision, efficiency, accuracy, and complexity, depending on programmer skills and abilities and programming decisions forcing design tradeoffs. A well written program should have speed, efficient use of available hardware resources, accuracy, and an inherently logical structure that aids documentation and subsequent modifications. Programs developed to fit specific requirements are termed customized software. A program organized and prepared for general commercial use is called a package, or a software package, and includes documentation for program use. A form of customized software that takes an existing program or package as its starting point and modifies it is called a customized package. A minicomputer program can be stored on computer cards, standard magnetic tape, magnetic cassette tape, floppy disk, or hard disk. The software purchaser or lessee may select one or more of these media when specifying a program in a software contract. Supporting documentation may include a listing of the program instructions linkages, hardware and storage resource requiremnents, flow charts, and programmer and user manuals. The purchaser must carefully make and clearly understand specifications for media and format of program delivery. This assures that delivered software is compatible with the intended hardware. Mineral Industry Attitudes Toward Computer Software The mining industry has traditionally been conservative concerning computer applications. Furthermore, large computer costs have made these systems accessible only to large companies, for the most part. But in the past few years, mining software systems developed at schools such as Pennsylvania State University and Virginia Polytechnic Institute have gained wider acceptance in the mineral industry. More mining engineers now have academic training in computer application, and computer use is now more acceptable to the mining industry. Mining managers in decisionmaking positions are faced with a new generation of computer technology resulting from the rapid evolution of minicomputers. Not too long ago, manufacturers such as Digital Equipment Corp., Data General, and Hewlett-Packard were considered newcomers. They are now established companies. In addition, Apple, Radio Shack, Commodore, and others have emerged in the growing microcomputer industry. So the mine manager or mining executive now has more options. Mining Software is Limited Along with the rapid evolution in hardware development, much general purpose software is now being developed for minicomputers. The 1981 Apple Software Directory can be obtained for about $14; Radio Shack published the Application Software Source Book in three volumes for $1.95 each. Brochures describing software can be obtained for other minicomputer manufacturers by contacting local sales representatives. Hewlett-Packard software can be obtained and exchanged through HP user's groups. Manufacturers' programming staffs are generally concerned with developing applications software. In some instances, manufacturers will recommend software developed by their hardware users. Until now, however, software development for mining applications has been minimal. This should not be surprising, since software development traditionally lags hardware development by several years. A review of A Directory of Computer Software Applications/Mini-Computers and Micro-Computers, August 1977-1980, published by the US Department of Congress, National Technical Information Service, contains many entries and subject areas. General applications include some references to tunneling machines, but there are virtually no entries specifically relating to

Jan 11, 1981

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903 +/- hectares (22,000 +/- acres) on Black Mountain, which contains the state’s highest point, as unsuitable for mining. A fast track legislative process was triggered which could have "taken"100 million tons of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed.

Jan 1, 2000

By M. Hancer, J. D. Miller

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCl. Precipitationof the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999