Search Documents

By Rafael Moure

On April 21, 1980 the Oil, Chemical and Atomic Workers Union (OCAW) submitted a petition urging the revision of the Mine Safety and Health Administration (MSHA) permissible exposure limit to radon daughters in underground mines. This petition asks for: 1. Annual worker exposure to be lowered from the current 4 WLM/year to 0.7 WLM/year; 2. Full economic protection for workers whose exposure exceeds the proposed 0.7 WLM/ year; and 3. The primary means of lowering workers' radiation exposures shall be environmental controls. I will present the scientific rationale for the lower standard requested in our petition to the Department of Labor. [1. Radiation Exposures to Uranium Miners] Two types of radiation exposures are present in the environment of uranium mines: A. [External Exposure] to gamma sources which until 1978 was considered as negligible compared with internal alpha radiation. R. E. Utting (1), in an investigation of three Canadian uranium mines, found levels of exposures adding to an annual dose equivalent of 3 rems (30 mSv)/year. He concluded that gamma dosages may be a major fraction of the maximum permissible dose for many individual miners. The U.S. experience has shown that there is significant gamma exposure in U.S. uranium mines and, therefore, it could contribute to the total radiation exposure to the lungs in combination with internal alpha radiation. Before ventilation improvements in uranium mines, the contribution of external radiation to total lung dosage was relatively small. After improvements in ventilation, the reduction in internal radiation exposure appears to be in 1980 as low as 1/10 of the 1950 dosages. However, ventilation improvements do not affect external gamma radiation. Gamma radiation remains at the same 1950's level, and it represents today a higher proportion of the total radiation burden to the miner's lungs. MSHA regulations (57.5-47) state that if gamma exposure is below 2.0 milliroentgens per hour, then workers are not required to wear gamma dosimeters and cummulative gamma radiation records need not be kept. Assuming an exposure of 1.9 milliroentgens per hour per 173 hours/month for 12 months,a miner would accumulate a dose from external radiation of 3.9 rems/ year. This dosage would, of course, go unrecorded. MSHA, therefore, should consider a downward revision of the external radiation permissible exposure limit of 2.0 milliroentgens/hour. MSHA should make clear that this exposure level, when added to the internal exposure, does not make for sound health physics -even though the measured current levels do not approach 2.0 milliroentgens/hour. B. [Internal Exposure] to alpha radiation is still the larger contributor to lung irradiation in uranium miners. The target organ is still the lung. The parameters to be considered in determining the biological radiation load appear in Table I for radon daughters present in the upper respiratory tract (URT). TABLE I RADIATION DOSE PARAMETERS IN THE URT OF URANIUM MINERS Parameter Uranium Underground Mining [1. Quantity of the Absorbed Radon daughters (Po-218, Nuclide Pb-214, Bi-214) deposit in bronchial and lung tissue. (Measured by air concentration, Working Levels) 2. Type of Radiation Emitted Alpha Particles 3. Energy of Radiation High-Linear Energy Transfer 4. Half-life of the Nuclide Ra 222, 3.8 days in the Organ Po-218 (RaA), T1/2 = 3.1 minutes Pb-214 (RaB), T1/2 = 26.8 minutes Bi-264 (RaC), Vi = 19.7 minutes 5. Selection Factor of the Direct inhalation with mine Organ dust to be deposited in the tipper Respiratory Tract 6. Mass and Form of the Organ Especially cancer sensitive, tracheobronchial region and bronchi* 7. Distribution of the Activity Dependent on deposited dust in the Organ distribution in the Upper Respiratory Tract 8. Chemical Nature of All compounds (RaA, RaB, RaC) Incorporated Substance biologically insoluble. (Only localized, irradiation) *See Reference (2)] The parameters of Table I depend, in turn, on the demography of the exposed population, especially: 1. Age 2. Sex 3. Health Status 4. Genetic Constitution 5. Lifestyle (Smoking, Diet) Some of these demographic characteristics of uran-

Jan 1, 1981

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By James P. Odendahl

Missouri is a state rich in mineral commodities. There is a variety of types of mining as well as minerals in the state. Different phases of mining are controlled by a variety of state and federal laws. What I hope to do today is to present briefly some of the interaction and interplay that has occurred in the recent years between the mineral industry and the Missouri regulatory agencies, as well as some of the interactions by federal agencies. First a little history which dates back to the late 1600's. For many years Missouri has been a leader in the production of lead and zinc. In fact, recent studies have indicated that Missouri produces better than three-fourths of the nation's present lead supply. Less well known but important resource is iron mining. Some of these operations were the source of confrontation during the Civil War. Major battles were fought in and around Ironton, Missouri where iron mining has occurred for many years. One of the largest pelletizing operations in the state is currently located within the city of Ironton. Joplin, Missouri, the home of Thomas Hart Benton, the famous Missouri painter, has a history of lead and zinc mining, going back to the later 1800's. Many of the paintings by Benton contain reference to the early days of mining in Missouri. There is a Benton mural in the City Hall at Carthage depicting the early days of lead mining in that area. Later, the center of lead mining moved to southeast Missouri near Bonne Terre and Flat River. The names of the towns in this area reflect the history of mining, examples - Leadington, Old Mines, Rivermines, etc. The history of lead mining in Missouri has been referred to in some detail in various publications(l).

Jan 1, 1977

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By C. B. Henderson

The development of slurries of coal and water as a boiler fuel replacing No. 6 fuel oil has been actively pursued at the Atlantic Research Corporation since 1976. Funding for this effort has been provided by the U.S. Department of Energy, the Electric Power Research Institute, and by corporate funds. The name ARC-COALTM has been selected for these slurries. Stable coal-water slurries with bone-dry coal loadings between 62% and 77% have been prepared, evaluated rheologically, and successfully burned in an experimental furnace without the assistance of other fuels. The advantages and properties of these slurries, including combustion results, are reviewed. Also discussed is the pilot line used for processing barrel quantities of fuel and a pilot plant capable of processing 600 bbl/day, currently being designed.

Jan 1, 1982

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By R. Gehauf

Magnetic separation using rare earth rolls (RER) and rare earth drums (RED) have seem tremendous development and use in recent years. While the process of magnetic separation is understood, the principles affecting the separation, the specific application and the optimization of RERs and REDs are less well known. This paper offers practical insight into the basic operation, selection and optimization of RERs and REDs. It is a guide for the engineer who must design a test series and select the proper equipment for that application. It provides the engineers and line operators who control the daily operation of the equipment a basic understanding of the dynamics of operation and the principles that govern the optimization of RERs and REDs.

Jan 1, 2004

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By F. D. Wang

This paper presents an innovative mining method with the application of the water jet. The basic principle of this mining method is to mine a thin panel slice with a water jet system and to allow the roof to deflect elastically and subsequently to be supported by the coal floor without artificial roof support. Through the sequential mining of layers from top to bottom, the entire seam is extracted and the roof rests upon the mine floor. The advantages of this method are that the safety of underground operation can be greatly increased and the surface overburden disturbance will be markedly reduced. . An economic evaluation of such a system is presented for the total cost estimated per ton of coal mined at the face. This evaluation is then compared to that of a continuous mining section utilizing a room and pillar mining method.

Jan 1, 1991

By Lawrence Pelham

The demand or consumption of fluorspar has been somewhat taken for granted in recent years, except for the specific interest of those that produce, market, and/or consume the commodity. A tradition was established of thinking that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today than in the past. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The Bureau of Mines recently published an assessment of world fluorspar reserves and resources that created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The United States and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. The goals for the U.S. Government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. This paper reviews the recent past of fluorspar and helps set the stage for a more detailed assessment of this critical commodity.

Jan 1, 1986

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By Aydin Shaterpour Mamaghani, Cemal Balci, Nuh Bilgin, Mucahit Namli, Hanifi Copur

"It is expected that more than 10 Billion USD will be spent in Istanbul in coming years on tunnel boring especially with EPB-TBMs. However, the geology of Istanbul is very complex. Geologic formations changing from Paleozoic to Cenozoic ages cause tremendous problems due to frequently changed rock formations and andesite and diabase dykes. This paper summarizes a universal model to predict the performance of EPB-TBMs which is created upon the data base collected from several projects. The model first is based on predicting field specific energy and power consumed of TBMs using geo-mechanical properties of the excavated material and TBM diameter. Later net production rate is calculated using field specific energy and power consumed by TBM. A methodology to predict machine utilization factor permits to calculate daily advance rates. The validity of the model is tested using the data obtained from two recent metro tunnel projects. 1. INTRODUCTION It is expected that in a near future a total length of 400 km will be excavated in Istanbul in a complex geology. Selecting proper tunneling equipment, organizing an effective operational management with the right tunneling crew will be a major concern for an efficient scheduling of the future projects necessitating to create a model to estimate daily advance rates. Several TBM performance prediction models with few on the prediction of machine utilization time were realized in the past. However, there is quite limited number of research studies on predicting the performance of EPB TBMs. Specially predicting daily advance rates in complex geology, in mixed face, in fractured rocks, in transition zones etc. are in big concern (Namli et al. 2013, 2014). The first experiences in Istanbul with a gripper type TBM was a nightmare, roof collapses caused big delays in tunnel excavation (Bilgin 1993). A typical example to EPB-TBM was Kadikoy-Kozyatagi tunnel, changing TBM from opened mode to closed mode with few modifications on the cutterhead resulted a tremendous increase in the daily advance rates (Bilgin et al. 2009). The data collected from several tunnelling projects served a basis to create a model to predict daily advance rates of EPB TBMs. Within the frame of a research program the validity of the model was tested in Uskudar-Umraniye–Cekmekoy-Sancaktepe metro project and very recently in Mecidiyekoy-Mahmutbey project."

Jan 1, 2016

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017

By Sharon G. Roness

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their: coal. Sulfur was the major concern. Btu content and sodium limited the market for some plants. The PRB market has now extended to plants that are converting from other coals because of the Clean Air Act. These new customers are more sensitive to constituents that affect boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to improve cost controls. Kerr-McGee Coal's Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998