Search Documents

By Akira Ishikuro, Masamichi Shintaku, Futoshi Kusumoto, Takeshi Kudo

"The Bankei-Kitanosawa tunnel that is located in Sapporo, Hokkaido, Japan includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. The mucks containing hazardous materials were disposed into the waterproof branch tunnels created from the inside of the main tunnel. The full face early ring closure method was employed to ensure the stability of the tunnel in the low strength rock masses having no stand-up time. As a result, the waterproof tunnels branching off the main tunnel can manage water tightness so as to ensure safety and relief against environmental risks of the hazardous materials. It is also demonstrated that the full face early ring closure method enable construction of the tunnel with a small overburden in the low strength rock masses. INTRODUCTION The Bankei-Kitanosawa tunnel includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. In order to overcome the restrictions, the hazardous materials were designed to be disposed into large cross section waterproof tunnels which were newly designed and constructed in high strength and hazardous material free Andesite. The lining for the tunnels was composed of with shotcrete. In addition, full face early ring closure (Sato et al., 2013) was employed to stabilize the tunnel so as to enable safe tunnel excavation in low strength rock masses where a ground arch is deemed unachievable. This paper presents the safe disposal method of mucks which are likely to liquate out natural hazardous materials as well as the full face early ring closure method and its mechanical characteristics."

Jan 1, 2016

By John D. Morgan

The U.S. economy annually needs over 4 billion tons of new mineral supplies. The value of domestically produced energy and processed materials of mineral origin exceeds $175 billion annually, but domestic production of both raw and processed minerals is not keeping pace with demand.

Jan 1, 1974

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994

By K. W. Harris, K. A. Perry

Underground coal mines beneath Black Mountain in the Harlan County district of the Central Appalachian coalfields have an extensive history of bump events, which yields an elevated probability for significant injury or fatality to underground miners. According to Mark (2009), Harlan County has had the greatest concentration of deep-cover retreat mining in the United States. Combined with the extensive multiple seam mining history, room-and-pillar coal bumps have had a disproportionate impact on coal operations in this region. The Harlan seam, one of the principal, economically recoverable coalbeds exploited beneath Black Mountain, has a significant burst history that extends into modern times. A numerical investigation using the LaModel software of 17 bumps that occurred at the same mine in the Harlan seam was conducted and used to create a calibration methodology which serves as the quantitative basis for current and future numerical efforts in an adjacent mine exploiting the same reserve. In addition to this numerical study, a qualitative assessment of the geologic factors that are believed to contribute to the bump potential was completed. Combined with stability prediction using the numerical basis, these geologic factors will be used for recognition of high bump potential areas with the goal of reducing the potential for future bumps, helping to ensure the highest level of safety and productivity for underground personnel.

Jan 1, 2016

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By D. W. McGlashan

Zeta potential changes were determined as a function of pH, metal ion, and surfactant concentrations. Prom the analysis of data, flotation experiments were carried out to correlate float-ability with the differences in zeta potential. Cassiterite in water bears a negative zeta potential, The zeta potential of cassiterite is sensitive to pH changes; the electric double layer arises from the preferential adsorption of H+ and OH- ions and subsequent ionization of the hydroxylated surface. It is suspected that hydronium-ion concentration may cause reversal in the sign of the zeta potential. The ZPC was found to occur at pH 3.4. Metallic ions and the hydrated ions thereof affect the zeta potential of cassiterite in differing degrees of intensity. Without prior activation, sulfonated surfactants do not change the zeta potential of cassiterite. Sodium alkyl aryl sulfonate is especially active on lead-activated cassiterite and ferric-activated cassiteriten Microcalorimetric fiests confimed the activity of ions on cassiterite and showed the hydrated character of cassiterite smfaces. Close correlation between zeta potential and microflotation results was achieved.

Jan 1, 1969

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By Rick Bearce, Minsu Cha, Mike Mooney, Yuanli Wu, Lisa Mori

"Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. Chamber pressures can reach 3-5 bar yet the vast majority of testing is performed under atmospheric conditions. This paper illustrates how pressure influences foam stability and conditioned soil behavior, and how atmospheric test results must be viewed in the context of expected chamber pressures. Torsional shear strength, compressibility and abrasivity of foam conditioned sand were found to be ideal when the void ratio was above the ASTM-determined maximum void ratio, achieved by sufficiently expanding the soil grain structure with foam, herein when the foam injection ratio at pressure exceeded 45%. Otherwise, the engineering properties of foam conditioned sand were not ideal, i.e., appreciable torque and abrasivity, low compressibility. INTRODUCTION Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. The formation soil at the cutterhead must be transformed into a highly compressible, low shear strength and low permeability medium within the excavation chamber to allow effective EPB performance. This behavior must be maintained for a certain residency time while the soil is in the chamber and screw conveyor. The vast majority of published studies on conditioned soil behavior have been performed under atmospheric conditions (Quebaud et al., 1998; Bezuijen et al., 1999; Psomas and Houlsby, 2002; Vinai et al. 2008; Thewes et al., 2012; Peila, 2014); however, the desired soil behavior must occur under chamber pressures that can reach 5-7 bar. The influence of pressure on conditioned soil is significant and is dramatically different than behavior under atmospheric pressure (Williamson et al., 1999; Mori et al., 2015). This paper illustrates how pressure influences conditioned soil behavior and how atmospheric test results must be viewed in the context of expected chamber pressures. The influence of pressure on foam bubble size (including with time) is shown through digital image analysis. The influence of pressure on foam half-life is also investigated. The compressibility, shear strength, and abrasivity of conditioned soil under pressure is presented and explained in terms of density, soil and air compressibility and porosity."

Jan 1, 2016

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By J. P. Hedlund

Molycorp's gravity type panel-caving operation employs a system of short raises to transfer ore from the Grizzly Level to the Haulage Level. The raises have normally been developed using a conventional drill-and-blast method or a combination conventional/raiseboring method. A new method was needed that would be less labor intensive, provide a safer work environment for personnel, provide a stable raise that could be self-supporting and a method that would be cost competitive with the conventional system.

Jan 1, 1991

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Kadri Dagdelen, Steven Hoerger

For gold mines, orebody uncertainty is one of the leading causes of differences between planned and actual production. Geostatistical conditional simulations create multiple equally probable orebody block model realizations which are conditional to the current drilling information and demonstrate the sampled grade distributions and spatial statistics. These simulated block models are key inputs for a stochastic evaluation to show the likely range of grades and cash flows to be delivered by a mine plan. The stochastic evaluation outputs can be used to compare different mine plans in terms of expected values and risks to planned grades, production, costs, Net Present Value (NPV) and other plan metrics. For the McLaughlin gold mine, risk profiles are demonstrated to show how different mine, cut-off and stockpile strategies can reduce risk and improve expected value. The strategies considered were effective in improving expected NPV and reducing or eliminating tonnage uncertainty, but the strategies had little impact on reducing the uncertainty of NPV’s or mill grades. The stochastic evaluation process is also used to compare the risk impact of orebody uncertainty against the risk of not achieving planned mining tonnages or vertical advance rates. Risks for plans created with and without stochastic mine plan optimization are also compared.

Feb 1, 2025

By Oliver Gutsche

High-pressure roll mill comminution of heterogeneous multicomponent feeds was simulated with artificial limestone-quartzite mixtures using a piston-die press. The influence of heterogeneous interactions between components of the mixture on grinding path, energy utilization and energy split have been examined. Primary fractures are governed by differential fracture strength and attrition resistance of the components at heterogeneous contacts; subsequent secondary and tertiary fracture events are governed by coarse-fine interactions in the particle-bed. The weaker component is preferentially ground out of the feed size fraction and concentrates in the fines. Energy split among the components in the mixture is a function of their relative fracture strengths. It doubles for limestone and decreases by a factor of 5 for quartzite over the entire range of the mixing ratio.

Jan 1, 1995

By H. Dho

Two aromatic-type chelating agents, 1,10 phenanthroline (phen) and 8-quinolinol (quin), were tested as specific depressants for magnetite in the cationic silica flotation of magnetic taconite concentrates. Micro and batch flotation tests, along with zeta potential and adsorption measurements were used. In the presence of a cationic collector, dodecylammonium chloride (DAC), the Fe/phen surface chelate electro-statically repelled DAC, and magnetite was depressed. The negatively charged Fe(quin)2(OH)2-on the magnetite surface attracted the cationic collector and made magnetite floatable.

Jan 1, 1995

By Venkata S. Vutukuri

Assuming a number of discrete leakage paths and treating the airflow through leaky duct line as a series-parallel combination of airflows along the duct and through leakage paths, exact solutions for auxiliary ventilation problems can be obtained. A computer program "SEGMENT'' has been written to solve problems using this method. However, most of the investigators have treated the duct lines with a uniformly distributed leakage and many have derived formulas assuming various boundary conditions and levels of simplification for the design of a simple auxiliary ventilation system An appraisal of accuracy of the various formulas has been conducted using the results from the program "SEGMENT' as benchmark and the formulas which give accurate results have been identified. The ranges of application for all the formulas have also been determined for 5 %error.

Jan 1, 1993

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By B. Petkof

Olivine has been an accepted industrial mineral for the last 50 years. Its initial acceptance was based on the recognition of its refractory properties by European research workers in the middle to late 1920's. Initial U.S. olivine production began in the early 1930's in North Carolina and continues there today. Olivine also is produced in the State of Washington and in other countries.

Jan 1, 1982

By M. M. Nash

Since the late 19th Century, scholars have been concerned about finding proper methods of managing business. The search seems to be taking us full-circle to the time and motion studies of Taylor (Horn, 1987). It wasn't until the late 1970's, however, that systematic investigations were made in the mining industry. One of the first was a study by Sanders, Patterson, and Peay (1976). That project explored the relationship of attitudes and safety. Peay, Atkin, and Goodman (1977, then reviewed the whole area of Organizational Development, including the so-called Rushton experiment.

Jan 1, 1988

By J. Loredo

In some rural regions of Peru, artisanal gold mining is currently an essential activity as it provides an important source of income. In the Huanca region (Ayacucho Department) gold deposits are not attractive for mining companies due to their reduced size, but they have enough interest for artisanal mining because of the ease and low cost of mining operations. Artisanal gold mining represents an important damage for the environment, because operations related to amalgamation processes using Hg result in special environmental problems besides the typical ones commonly associated to all mining activities. A preliminary sampling has been made in soils, materials from tailing ponds and surface water of the Acarí River, at the site of the Huanca village, according to networks specially designed for the particular conditions of the area. Studies accomplished revealed high mercury concentrations in soils and tailings. Chemical analyses of soils directly collected in the area of the active or abandoned ?quimbaletes? show mercury concentrations ranging from 15.3 mg?kg-1 to 44.2 mg.kg-1. Mercury concentrations in soils decrease as a function of distance from the before mentioned sources. Water quality of the Acarí River that flows through the area does not present important changes as a consequence of the mining and processing operations.

Jan 1, 2006

Since first introduced, the coal mine roof rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground-control problem: extended cuts. Extended cuts, i.e., cuts greater than 6 m (20 ft) in length, are commonly used with remote-control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof-falls. When extended cuts are attempted in weak roof material, the roof may collapse before it can be bolted Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended-cut experience were collected at 36 mines in seven of the United States. It was found that, when the CMRR was greater than 56, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken, and, when the CMRR was between 38 and 56, extended cuts were sometimes, but not always, feasible. The data also show that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 2000