Search Documents

Mineralogical and metallurgical scoping testwork were carried out to investigate the production of separate, marketable gold and platinum concentrates. The study utilized a flotation concentrate assaying approximately 5 wt% gold and 5 grams per tonne platinum. The gold-platinum mineralization was recovered from a placer deposit. Optical microscopy and scanning electron microscopy with energy dispersive x-ray analysis identified gold as zoned Au- Ag and Au-Ag-Cu alloys. Platinum primarily occurred as weakly zoned, variably magnetic Pt- Pd-Fe alloys. A combination of gravity and magnetic separations resulted in a gold concentrate grading 86.9 wt% Au (and 9.lwt% Ag) and a separate platinum concentrate grading 400 g/t Pt with recoveries of 94.5% and 96.7%, respectively. Magnetohydrostatic separation (MHS) using the Magstream 200 Separator indicated promising results.

Jan 1, 1994

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By Luis M. González, Guzmánm Guillermo D., Davis Juan C.

"The Teniente converter (CT) of the Ventanas Smelter and Refinery of Codelco-Chile has two tuyeres for dry concentrate injection directly into the melt.The diluted phase injection system can feed 15 to 20 kg of concentrate for 1 kg of air, which creates a very abrasive solid/gas phase. The tuyeres commonly used lasted for about 3.5 days due to the accelerated decay of the shell, and 1.5 hours were necessary for the replacement of new ones in the reactor.Tests were carried out with common shell tuyeres with a tungsten based welding cover, and a life span of 28 days was reached, increasing the Teniente converter operational continuity between 1.5 to 2 %."

Jan 1, 2009

By Cheng Pan, Xuewei Lv, Guibao Qiu, Chenguang Bai, Meilong Hu

"Physic-chemical properties of slag at high temperature play an important role in the pyrometallurgical process of production of ferronickel alloy. It determines the operation efficiency, metal recovery ratio, energy consumption and the distribution of elements like S and P between the slag and metals. In the present work, the effect of MgO content in the slag on melting features and viscosity of the slag was investigated. The MgO content in the SiO2-CaO-MgO-Al2O3 -FeO in the quinary slag system varied from 14.5% to 22.5%. The results shown that all slag samples begin to softening at the same temperature, the softening temperature, melting temperature, flowing temperature decrease with the increase of MgO content when the MgO content is in range of 14.5 and 20.5 pct mass, and when MgO content up to 22.5 percent, the temperatures increase sharply. Besides the inflection point temperature of viscosity-temperature curve increase with the increase of MgO when the MgO content is in range 16 and 22.5 pct mass.IntroductionNickel is very important to modern society, without it, we would not be able to share many things in our daily life, such as airplanes, computers and many stainless steel appliances in our homes and workplaces1.. It is the essential element of the stainless steel making, and about 65% of the nickel consumed in the world is used to make stainless steel2., so with the increase of stainless steel, the nickel production and demand has continued to increase3.Nickel is produced from two distinct ore types: nickel sulfide deposits and oxide nickel laterite deposits. The great majority of world’s known nickel resources are contained in laterite deposits3.. The laterite ores are normal classified into two groups: the high-iron laterite ore and high-magnesia laterite ore1. Typical composition of high-magnesia laterite ore is in the range 1-3%, and these ores are suitable for pyrometallurgical process to produce ferronickel4."

Jan 1, 2012

By Ana P. Paiva, Marc F. Comella, Sandra S. Reis, Joao N. Reis, M. Soledade Santos

"In this work, the influence of the malonamide structure, acidity of the aqueous phase and diluent on the equilibrium interfacial tension (IT) of N,N'-dimethyl-N,N'-diphenylmalonamide (DMDPHMA) and N,N'-dimethyl-N,N'-dicyclohexylmalonamide (DMDCHMA) in 1,2- dichloroethane (1,2-DCE), and DMDCHMA in toluene, with aqueous HCl, were investigated. IT isotherms were determined using the Du N ouy ring method. Densities of the organic phases were determined, and used to screen solute-diluent interactions. Formation of third phases was never observed; furthermore, ITs increase with the phase separation period, constant values being obtained for separation periods larger than 1000 seconds. Each malonamide interfacial efficiency at the oil/water interface is interpreted in terms of malonamide basicity, diluent polarity and malonamide - hydrochloric acid- diluent interfacial interactions.IntroductionFor several years now, N,N'-tetrasubstituted malonamide derivatives have been extensively investigated as liquid-liquid extraction agents since they were first proposed as the organic components of the DIAMEX process, with the aim of advantageously replacing tributylphosphate in PUREX [1]. Therefore, a significant part of research studies with malonamides appearing in the literature deal with the extraction of major and minor actinides in real or simulated spent nuclear fuels in nitric acid solutions [2]. Under typical experimental process conditions, the tendency shown by some N,N'-tetrasubstituted malonamide derivatives to aggregate in the organic phase, leading in a few cases to the formation of undesirable third phases, has been remarked and consequently thoroughly investigated [3, 4]. The increasing use of chloride streams as hydrometallurgical aqueous feeds is becoming a reality, and this fact is obviously deeply founded on an extensive research carried out to recover value-adding metals from these media. Following this trend, a number of N,N'-tetrasubstituted malonamides have already been screened for the recovery of iron(III) [5, 6] and platinum-group metals [7] from hydrochloric acid solutions. The results obtained are quite promising either in terms of total metal ion recoveries or selectivity patterns achieved. The formation of a third phase when iron(III) was extracted by the tested N,N'-tetrasubstituted malonamide derivatives has never been observed under the adopted experimental conditions, and the extraction data collected would need to be reinterpreted accordingly if any aggregation phenomena involving the considered extraction systems were to take place."

Jan 1, 2011

By Aureo D. V. Machado

An experimental study to obtain zirconia powders (ZrOz) from carboxylate zirconium solutions followed by hydrogen peroxide stripping and precipitation, has been carried out. Zirconium carboxylate was prepared by solvent extraction from a chloride aqueous phase using magnesium carboxylate as organic phase. The variables examined in the precipitation reaction were: Temperature: 25 - 90 ?C ? H202= concentration: 0.3 - 5% wt/wt - pH: 1 ? 9 Organic/Aqueous ratio (1/1) and reaction time (30 minutes) were maintained at constant levels. The optimum results (98% precipitation) were achieved at 25 °C, 5 % wt/wt H202=, and pH = 5. The precipitates were composed of large amorphous aggregates (<I00 micrometers). After calcination for 1 hour at 1000 OC, monoclinic ZrO2 with a large variation in particle size (1 -100 micrometers) was obtained.

Jan 1, 1991

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By Daoxin Wu, Zhong Cao, Yan Shi, Yu Ding, Huanli Yang, Zhongliang Xiao

"2-substituted benzimidazole-zinc and 2-substituted benzimidazole-copper complexes were main components of organic solderability preservative (OSP) in PCB producing process and affect the thermal stability of OSP film. So these four complexes were prepared by 2-substitutedbenzimidazole reacting with zinc ion and copper ion, the complexes crystals were determined by IR, its thermal stabilities were studied by TG method. The results indicated that the thermal stability of 2-substituted benzimidazole-zinc is higher than the 2-substituted benzimidazole copper,and the thermal decomposition mechanism was presentedIntroductionImidazole compounds which is an important heterocyclic compound shows the important value and outstanding prospects[I-3l in field of biological engineering, medicine, and high-performance composites. It's said that imidazole compounds is an excellent new metal surface treatment[4] agent, because it has good reaction activity with metals and can form a chemical layer on the metal surface. The complexes of imidazole were main components of organic solderability preservative (OSP) in PCB producing process and affect the thermal stability of OSP film. The mechanism of imodazole combined with metal and film deposited has been reported, but the opinions about thermal stability of film have bifurcation, let alone the thermal decomposition mechanism of film at high temperature. The complexes were prepared by combining of 2- substituted-benzimidazole with zinc and copper iron, which were studied by IR and TG method, in order to get thermal stability of different complexes."

Jan 1, 2011

By Metehan Erdogan, Orhan Gökçe Göksu, Ishak Karakaya

"An experiment (mixture) design was created to optimize the process parameters of the electrochemical reduction of CaW04 to W in molten CaCl2-NaCl eutectic mixture. Temperature, applied voltage and the length of Kanthal wire winding of the CaW04 pellets were selected as the process parameters that were allowed to vary between the predetermined minimum and maximum values. The rates of the electrochemical reductions were interpreted from the variations of current and total charge vs. time graphs under different conditions. The analysis pointed out that 640°C and 2.81 V resulted in the fastest reduction. Itwas seen that the effect of Kanthal wire winding on the output current was less pronounced when compared to the other two parameters.IntroductionFFC Cambridge Process [1] has been applied to a number of metal oxides in laboratory experiments to produce metals. In nearly all of these studies, the electrolysis temperature was around 900°C, the electrolyte was pure CaCl2 or CaCl2 containing salt solutions and the anode was graphite. However, it was recently shown that the electrochemical reduction process of metal oxides in CaCl2 containing electrolytes at the mentioned high temperatures was not suitable for tungsten production [2], It was reported that as soon as WO3 contacts CaCl2, the following reaction occurs:"

Jan 1, 2012

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Noboru Masuko, Sachiko Ono

"The structure and composition of anodic films formed on aluminum in a borate solution have been investigated by using TEM and SIMS with respect to the effect of current density and electrolyte temperature. The film is composed of a boron-containing outer layer and a boron-free inner layer with disc-like crystals present at the interface. The thickness of the film formed at constant current density up to an identical voltage, decreases with increasing current density. The thickness increases remarkably with elevated temperature. The transport number of Al3+ estimated from the thickness ratio .of the cuter to the inner layers is 0.4 when the film is formed at the current density of 20 Am-2 at 60°C. It increases slightly with increasing current density and decreases significantly with increasing temperature. Content of boron in the outer layer increases 1.5 times when current density .increases 10 times. These changes in film structure and composition with electrolysis conditions must have a significant role in the determination of electric properties of anodic alumina films as a capacitor material.IntroductionThe growth of anodic alumina film in ·a neutral electrolyte proceeds at both film/electrolyte and film/substrate interfaces giving a duplex structure. The oxide layer formed at the former interface includes electrolyte anions while a-pure alumina layer is formed at the latter interface. The thickness ratios of each layer respectively represent transport numbers of Al3+ and 0 2 - (1). The film thickness and the incorporated anion content as well as transport numbers of both ions must affect the dielectric properties of the film as a capacitor material. However, the correlation between film structure and electrolytic conditions is not fully understood (2). For the further clarification of anodic film growth mechanism, more detailed characterization of anodic films in relation to electrolytic conditions is advantageous. In the present paper, therefore, the effect of current density and electrolyte temperature on the microstructure and composition of anodic barrier films formed in a neutral borate solution was studied. The films were characterized by direct observation using transmission electron microscopy (TEM) and depth profiles of constituent elements obtained by secondary ion mass spectroscopy (SIMS)."

Jan 1, 2000

By Yoshio Waseda

A laser flash method has been applied to obtain the thermal diffusivity values of Zr55Al10Ni5Cu30 alloy in the liquid, glassy, crystallized and supercooled liquid states. The electrical resistivity of this particular alloy was measured in the glassy, and crystallized states by a direct current four probe technique. A specific heat of Zr55Al10Ni5Cu30 alloy was also determined by a differential scanning calorimeter in the glassy state. On the other hand, thermal diffusivity values for two alloys of Zr60Al15Ni25 and Zr65Al7.5Cu27.5 were measured in the crystallized and liquid states. The thermal diffusivity values of three Zr-based alloys in the liquid state are summarized in the linear equations with positive temperature dependency and it is noted that the lower the thermal diffusivity values of Zr-based alloys at liquidus temperature, the lower the critical cooling rate to obtain metallic glass phase becomes. The thermal diffusivity values of Zr-based alloys were compared with those of Pd-based alloy case. These results suggest that thermal diffusivity of alloy liquids might be an indicator of the glass-forming ability of Zr-based and Pd-based alloys.

Jan 1, 2006

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By A. Ohno

"A new near net shape casting process, OHNO Continuous Casting (OCC), has been recently developed. In this process, molten metal is fed into a heated mold maintained at a temperature above the solidification temperature of the metal being cast. Solidification begins from the central core of the casting rather than the wall of the mold. With the heated mold, the formation of crystals on the mold wall is prevented and solidification occurs out of contact with the mold surface. This produces near net shaped products with smooth, mirror-like surfaces and unidirectional grain structures free from cavities, porosity and segregation. Any crystals formed at the beginning of solidification decrease in number as solidification progresses and eventually a single crystal product is obtained. This process is applicable to any metal alloys, converting them into new materials with superior properties and quality.IntroductionAs a result of growing technical demands for more advanced and diversified materials, the OHNO Continuous Casting (OCC) technology has found many new applications in industry. Considerable interest in the process has been shown in Japan and other countries because of its distinct ability to:produce a single crystal, (1)produce a remarkably clean cast surface without a witness mark,provide extremely good ductility,and reduce casting defects and segregation.This paper provides an overview of the principle of the OCC process and describes the remarkable characteristics of the material produced by this method."

Jan 1, 1988

By L. M. Bianchi

"Oxide, nitride and other compound coatings often do not have adequate properties for newer applications when produced using very high deposition rates and simple evaporation techniques. Solar control, abrasion resistance, low reflectance and barrier effective engineered coatings require exacting properties. Such properties can be obtained by adapting the activated reactive evaporation (ARE) technology to Web production processes. Adaptions of the HAD and MAD processes will be described along with data on the high deposition rates obtained. These fast production capabilities were developed in order to make the processes economically competitive.IntroductionThe Physical Vapor Deposition technique (PVD) has been used to coat steel strip for over 20 years. (1) However, its use as a production process has been very limited because of the high cost of the PVD coating process and because, in some instances, the properties of the coating were not good enough to meet the customers requirements. Nevertheless, the PVD process has found wide application in the airplane engine and electronic component markets. These production processes have stimulated further development and advances in the technology.In 1971, Profession R. F. Bunshah developed the Activated Reactive Evaporation (ARE) process which was then used to produce hard coatings such as carbides, nitrides, oxides and other refractory compounds. (2) The process from a fundamental viewpoint -produces a coating on the substrate via the evaporation of metal in the presence of a low pressure (typically around 1 millitorr) of reactive gas, with a plasma created in the space between the metal source and the substrate.The plasma may be created by many means but its function is two-fold. First, it activates the reaction between the metal vapors and the reactive gas atoms/molecules resulting in the formation of a compound that deposits on the substrate. Second, because the plasma is in contact with the substrate, it results in a negative bias on the substrate and produces bombardment of the growing film with ions and energetic neutrals from the plasma. This bombardment causes many significant changes in the microstructure, properties and appearance of the coating.Recently another new technology Pulsed Magnetron Systems (PMS) has been introduced into PVD. This new technology has been pioneered in production scale equipment by Dr. S. Schiller (3) and associates. The use of a pulsed power supply on the magnetron prevents the problem of the anode being coated with a insulating layer which will then lead to micro and macro arcing producing defects in the coating."

Jan 1, 1998

By Thomas Brynjulfsen, Merete Tangstad, Eli Ringdalen

Manganese ore fines cannot be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace, they are typically agglomerated into sinter. In this work, the melting and reduction properties of Gabonese sinter and Gabonese ore have been investigated in pilot scale experiments. Two experiments were conducted, one with 100% sinter as manganese source and one with 50/50 sinter and ore. Lime was used to achieve a charge basicity of 0.72 in both experiments. The composition of slag samples from the excavation of the furnace was established using EPMA(WDS), and the composition of the tapped slag and metal was found using XRF. It was found that while the coke-bed size would determine the tapped slag composition, the melting behavior of the Mn source would determine the mixing with lime.

Jan 1, 2014

By In-Ho Chi

In copper metallization, resistivity of copper seed layer is very important since the thickness of seed layer is less than 200iun. Conventionally MOCVD has been used for this purpose however electroless copper plating is simple process and the resistivity of copper deposit is less than that of copper prepared by MOCVD. In this study eIectroless depositions of copper were conducted on different substrate to find optimum conditions of electroless copper plating for electronic applications. To find optimum conditions, the effects and selectivity of activation method on several substrates were investigated. The effects of copper bath composition on morphology were investigated. The effects of pH and stabilizer on deposition rate was investigated. The resistivity of copper with thickness was also measured.

Jan 1, 2001

By Shun Myung Shin, Dong Hyo Yang

Cobalt is recovered from square type of spent lithium ion batteries (LIBs) containing 5~20 % Co, 5~7 % Li, 5~10 % Ni, 15% organic chemicals, and 7% plastics together with Cu, Al, Fe, and Mn. The waste LIB was prepared by physical treatment. After screening, the crushed LIBs were separated to +8 mesh, -8/+16 mesh, and -16 mesh powder. Among these, -16 mesh powder was selected for leaching. The leaching test was investigated at 2 M H2SO4, 6 vol.% H2O2, reaction temperature 60 ?, agitation speed 300 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of cobalt was more than 99 % and its concentration was 24.9 g/L. For removing of impurities such as copper, iron, and aluminum in the leaching solution before cobalt solvent extraction, the impurities were eliminated by pH control with alkali solution. For selective extraction of cobalt, the aqueous phase removed impurities was equilibrated with different volumes of 0.4 M Cyanex 272 saponified of 50 %. Extraction efficiency of cobalt was about 80 % at first step. Separation coefficient (ßCo/Li) of cobalt and lithium extractions was 206.5. Over 9.0 % of pure cobalt sulfate solution was obtained after stripping with H2SO4 solution.

Jan 1, 2008

By Zhijing Zhang

Sodium borosilicate is the basic composition of coating materials, Vycor and Pyrex glasses. In the present study, viscosities of Na2O-Si02-B2O3 ternary melts were measured under various compositions and temperatures. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on present experimental results, the previous structure based viscosity model was modified. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. The fitting ranges of the model cover the composition of XB2O3 from 0.1 to 0.6 combined with xSio2 / xNa2O = 0.5, 1,2 and 5 respectively.

Jan 1, 1998

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at I 300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt% iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003